162 lines
6.3 KiB
Plaintext
162 lines
6.3 KiB
Plaintext
/**
|
|
@page PWR_CurrentConsumption PWR Current Consumption example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file PWR/PWR_CurrentConsumption/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWR Current Consumption example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to configure the system to measure the current consumption in different
|
|
low-power modes.
|
|
|
|
The Low Power modes are:
|
|
- Sleep Mode
|
|
- STOP mode with RTC
|
|
- STANDBY mode without RTC and BKPSRAM
|
|
- STANDBY mode with RTC
|
|
- STANDBY mode with RTC and BKPSRAM.
|
|
|
|
To run this example, user has to follow the following steps:
|
|
1. Select the Low power modes to be measured by uncommenting the corresponding
|
|
line inside the stm32f4xx_lp_modes.h file.
|
|
@code
|
|
/*#define SLEEP_MODE*/
|
|
/*#define STOP_MODE*/
|
|
/*#define STANDBY_MODE*/
|
|
#define STANDBY_RTC_MODE
|
|
/*#define STANDBY_RTC_BKPSRAM_MODE*/
|
|
@endcode
|
|
|
|
2. Use an external amperemeter to measure the IDD current.
|
|
|
|
3. This example can not be used in DEBUG mode,this is due to the fact that the
|
|
Cortex-M4 core is no longer clocked during low power mode so debugging
|
|
features are disabled
|
|
|
|
Here below a detailed description of the example code:
|
|
|
|
@verbatim
|
|
|
|
1. After reset, the program waits for Key button connected to the PA.00 to be
|
|
pressed - LED blue (LED6) is blinking - to enter the selected low power mode.
|
|
- When the RTC is not used in the low power mode configuration, press
|
|
again the Key button to exit the low power mode.
|
|
|
|
- When the RTC is used, the wakeup from low power mode is automatically
|
|
generated by the RTC (after 20s).
|
|
|
|
2. After exit from Low power mode the LED6 is turned On.
|
|
- When returninng from Standby mode, LED green (LED4) is ON.
|
|
3. The sequence will be repeated from step 1
|
|
|
|
2. Low power modes description:
|
|
|
|
- Sleep Mode
|
|
============
|
|
- System Running at PLL (84MHz)
|
|
- Flash 5 wait state
|
|
- Instruction and Data caches ON
|
|
- Prefetch OFF
|
|
- Code running from Internal FLASH
|
|
- All peripherals disabled.
|
|
- Wakeup using EXTI Line (USER Button PA.00)
|
|
|
|
- STOP Mode
|
|
===========
|
|
- RTC Clocked by LSI
|
|
- Regulator in LP mode
|
|
- HSI, HSE OFF and LSI if not used as RTC Clock source
|
|
- No IWDG
|
|
- FLASH in deep power down mode
|
|
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
|
|
|
|
- STANDBY Mode
|
|
==============
|
|
- Backup SRAM and RTC OFF
|
|
- IWDG and LSI OFF
|
|
- Wakeup using WakeUp Pin (PA.00)
|
|
|
|
- STANDBY Mode with RTC clocked by LSI
|
|
==========================================
|
|
- RTC Clocked by LSI
|
|
- IWDG OFF and LSI OFF if not used as RTC Clock source
|
|
- Backup SRAM OFF
|
|
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
|
|
|
|
- STANDBY Mode with RTC clocked by LSI and BKPSRAM
|
|
======================================================
|
|
- RTC Clocked by LSI
|
|
- Backup SRAM ON
|
|
- IWDG OFF
|
|
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
|
|
|
|
@endverbatim
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Power, STOP, Sleep, Standby, Current Consumption, Low Power, LSI, Backup SRAM, Voltage range
|
|
|
|
@par Directory contents
|
|
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- PWR/PWR_CurrentConsumption/Inc/main.h Main program header file
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_lp_modes.h STM32F4xx Low Power Modes header file
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_it.c Interrupt handlers
|
|
- PWR/PWR_CurrentConsumption/Src/main.c Main program
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_hal_msp.c HAL MSP module
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_lp_modes.c STM32F4xx Low Power Modes source file
|
|
- PWR/PWR_CurrentConsumption/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F401xCx devices.
|
|
- This example has been tested with STMicroelectronics STM32F401-Discovery RevB
|
|
boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32F401-Discovery Set-up
|
|
- Use LED4, LED3, LED 5, LED6 connected respectively to PD.12, PD13, PD.14 & PD15 pins.
|
|
* LED5 (RED) will be ON if initialization fails.
|
|
* LED6 (BLUE) will toggle waiting for user to launch test, then be turn OFF
|
|
* LED6 (BLUE) will toggle while executing RTC wakeup callback in any mode.
|
|
* LED4 (GREEN) will be ON while returning from STANDBY mode (PWR flag check callback)
|
|
- Use USER Button connected to PA.00 pin.
|
|
- Connect an amperemeter to jumper JP2 to measure the IDD current
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|