109 lines
4.5 KiB
Plaintext
109 lines
4.5 KiB
Plaintext
/**
|
|
@page WWDG_Example Window Watchdog example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file WWDG/WWDG_Example/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the Window Watchdog example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example guides you through the different configuration steps by means of the
|
|
HAL API to perform periodic WWDG counter update and simulate a software fault that
|
|
generates an MCU WWDG reset when a predefined time period has elapsed.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 180 MHz.
|
|
|
|
The WWDG peripheral configuration is ensured by the HAL_WWDG_Init() function.
|
|
This later is calling the HAL_WWDG_MspInit()function which core is implementing
|
|
the configuration of the needed WWDG resources according to the used hardware (CLOCK,
|
|
GPIO, DMA and NVIC). You may update this function to change WWDG configuration.
|
|
|
|
The WWDG timeout is set, through counter value, to 46 ms.
|
|
The refresh window is set in order to make user wait 35 ms after a wadchdog refresh,
|
|
before writing again counter. Hence the WWDG counter is refreshed each (35 + 1) ms in the
|
|
main program infinite loop to prevent a WWDG reset.
|
|
|
|
LED2 is also toggled each 39ms indicating that the program is running.
|
|
|
|
An EXTI Line is connected to a GPIO pin, and configured to generate an interrupt
|
|
on the rising edge of the signal.
|
|
|
|
The EXTI Line is used to simulate a software failure: once the EXTI Line event
|
|
occurs by pressing the User push-button (PC.13), the corresponding interrupt is served.
|
|
|
|
In the ISR, a write to invalid address generates a Hardfault exception containing
|
|
an infinite loop and preventing to return to main program (the WWDG counter is
|
|
not refreshed).
|
|
|
|
As a result, when the WWDG counter falls to 63, the WWDG reset occurs.
|
|
|
|
If the WWDG reset is generated, after the system resumes from reset, LED1 is turned ON.
|
|
|
|
If the EXTI Line event does not occur, the WWDG counter is indefinitely refreshed
|
|
in the main program infinite loop, and there is no WWDG reset.
|
|
|
|
LED3 is turned ON and remains ON if any error occurs.
|
|
|
|
@note This example must be tested in standalone mode (not in debug).
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in SysTick ISR. This
|
|
implies that if HAL_Delay() is called from a peripheral ISR process, then
|
|
the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
System, WWDG, Downcounter, MCU Reset, Timeout, Software fault
|
|
|
|
@par Directory contents
|
|
|
|
- WWDG/WWDG_Example/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- WWDG/WWDG_Example/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- WWDG/WWDG_Example/Inc/main.h Header for main.c module
|
|
- WWDG/WWDG_Example/Src/stm32f4xx_it.c Interrupt handlers
|
|
- WWDG/WWDG_Example/Src/main.c Main program
|
|
- WWDG/WWDG_Example/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- WWDG/WWDG_Example/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F446xx devices.
|
|
|
|
- This example has been tested with NUCLEO-446ZE Rev.B board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
|
|
*/
|