This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.
/**
@page HID_Standalone USB Device Human Interface (HID) application
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file USB_Device/HID_Standalone/readme.txt
* @author MCD Application Team
* @brief Description of the USB HID application.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Application Description
This application shows how to use the USB device application based on the Human Interface (HID) on the STM32F4xx devices.
This is a typical application on how to use the STM32F446ZE USB OTG Device peripheral where the STM32 MCU is
enumerated as a HID device using the native PC Host HID driver to which the NUCLEO-F446ZE
board is connected, in order to emulate the mouse using user button mounted on nucleo board.
At the beginning of the main program the HAL_Init() function is called to reset all the peripherals,
initialize the Flash interface and the systick. The user is provided with the SystemClock_Config()
function to configure the system clock (SYSCLK) to run at 180 MHz. The Full Speed (FS) USB module uses
internally a 48-MHz clock which is coming from the PLL SAI.
The 48 MHz clock for the USB FS can be derived from one of the two following sources:
– PLL clock (clocked by the HSE): If the USB uses the PLL as clock source, the PLL clock must be programmed
to output 48 MHz frequency (USBCLK = PLLVCO/PLLQ).
– PLLSAI clock (clocked by the HSE): If the USB uses the PLLSAI as clock source, the PLLSAI clock must be programmed
to output 48 MHz frequency (USBCLK = PLLSAIVCO/PLLSAIP).
This application supports remote wakeup (which is the ability of a USB device to bring a suspended bus back
to the active condition), and the Key button is used as the remote wakeup source.
By default, in Windows powered PC the Power Management feature of USB mouse devices is turned off.
This setting is different from classic PS/2 computer functionality. Therefore, to enable the Wake from
standby option, user must manually turn on the Power Management feature for the USB mouse.
To manually enable the wake from standby option for the USB mouse, proceed as follows:
- Start "Device Manager",
- Select "Mice and other pointing devices",
- Select the "HID-compliant mouse" device
- Make sure that PID &VID are equal to 0x5710 & 0x0483 respectively by selecting "Details" tab
and setting Property to "Hardware Ids"
- Right click and select "Properties",
- Select "Power Management" tab,
- Finally click to select "Allow this device to wake the computer" check box.
The function GetPointerData() is responsible to move the mouse cursor automatically,
which can be easily customized (square, circle...). In this application the cursor
is moving forward and backward in an infinite loop.
LED1, LED2 and LED3 are blinking continuously.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
For more details about the STM32Cube USB Device library, please refer to UM1734
"STM32Cube USB Device library".
@par Keywords
Connectivity, USB_Device, USB, HID, Full Speed, High Speed, Joystick, Mouse, Keyboard, enumerate
@par Directory contents
- USB_Device/HID_Standalone/Src/main.c Main program
- USB_Device/HID_Standalone/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
- USB_Device/HID_Standalone/Src/stm32f4xx_it.c Interrupt handlers
- USB_Device/HID_Standalone/Src/usbd_conf.c General low level driver configuration
- USB_Device/HID_Standalone/Src/usbd_desc.c USB device HID descriptor
- USB_Device/HID_Standalone/Inc/main.h Main program header file
- USB_Device/HID_Standalone/Inc/stm32f4xx_it.h Interrupt handlers header file
- USB_Device/HID_Standalone/Inc/stm32f4xx_hal_conf.h HAL configuration file
- USB_Device/HID_Standalone/Inc/usbd_conf.h USB device driver Configuration file
- USB_Device/HID_Standalone/Inc/usbd_desc.h USB device HID descriptor header file
@par Hardware and Software environment
- This application runs on STM32F446xx devices.
- This application has been tested with STMicroelectronics NUCLEO-F446ZE Rev.B boards
and can be easily tailored to any other supported device and development board.
- NUCLEO-F446ZE Set-up
- Connect the NUCLEO-F446ZE board to the PC through 'USB micro A-Male
to A-Male' cable to the connector:
- CN13: to use USB Full Speed (FS)
- Make sure that the jumper JP4 is closed
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the application
*/
3d6be4bd40