/**
@page PWR_CurrentConsumption PWR Current Consumption example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file PWR/PWR_CurrentConsumption/readme.txt
* @author MCD Application Team
* @brief Description of the PWR Current Consumption example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to configure the system to measure the current consumption in different
low-power modes.
The Low Power modes are:
- Sleep Mode
- STOP mode with RTC
- STANDBY mode without RTC and BKPSRAM
- STANDBY mode with RTC
- STANDBY mode with RTC and BKPSRAM.
To run this example, user has to follow the following steps:
1. Select the Low power modes to be measured by uncommenting the corresponding
line inside the stm32f4xx_lp_modes.h file.
@code
/*#define SLEEP_MODE*/
/*#define STOP_MODE*/
/*#define STANDBY_MODE*/
#define STANDBY_RTC_MODE
/*#define STANDBY_RTC_BKPSRAM_MODE*/
@endcode
2. Use an external amperemeter to measure the IDD current.
3. This example can not be used in DEBUG mode,this is due to the fact that the
Cortex-M4 core is no longer clocked during low power mode so debugging
features are disabled
Here below a detailed description of the example code:
@verbatim
1. After reset, the program waits for Key button connected to the PA.00 to be
pressed - LED blue (LED6) is blinking - to enter the selected low power mode.
- When the RTC is not used in the low power mode configuration, press
again the Key button to exit the low power mode.
- When the RTC is used, the wakeup from low power mode is automatically
generated by the RTC (after 20s).
2. After exit from Low power mode the LED6 is turned On.
- When returninng from Standby mode, LED green (LED4) is ON.
3. The sequence will be repeated from step 1
2. Low power modes description:
- Sleep Mode
============
- System Running at PLL (100 MHz)
- Flash 5 wait state
- Instruction and Data caches ON
- Prefetch OFF
- Code running from Internal FLASH
- All peripherals disabled.
- Wakeup using EXTI Line (USER Button PA.00)
- STOP Mode
===========
- RTC Clocked by LSI
- Regulator in LP mode
- HSI, HSE OFF and LSI if not used as RTC Clock source
- No IWDG
- FLASH in deep power down mode
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
- STANDBY Mode
==============
- Backup SRAM and RTC OFF
- IWDG and LSI OFF
- Wakeup using WakeUp Pin (PA.00)
- STANDBY Mode with RTC clocked by LSI
==========================================
- RTC Clocked by LSI
- IWDG OFF and LSI OFF if not used as RTC Clock source
- Backup SRAM OFF
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
- STANDBY Mode with RTC clocked by LSI and BKPSRAM
======================================================
- RTC Clocked by LSI
- Backup SRAM ON
- IWDG OFF
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
@endverbatim
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Power, STOP, Sleep, Standby, Current Consumption, Low Power, LSI, Backup SRAM, Voltage range
@par Directory contents
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_hal_conf.h HAL configuration file
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_it.h Interrupt handlers header file
- PWR/PWR_CurrentConsumption/Inc/main.h Main program header file
- PWR/PWR_CurrentConsumption/Inc/stm32f4xx_lp_modes.h STM32F4xx Low Power Modes header file
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_it.c Interrupt handlers
- PWR/PWR_CurrentConsumption/Src/main.c Main program
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_hal_msp.c HAL MSP module
- PWR/PWR_CurrentConsumption/Src/stm32f4xx_lp_modes.c STM32F4xx Low Power Modes source file
- PWR/PWR_CurrentConsumption/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
@par Hardware and Software environment
- This example runs on STM32F411xE devices.
- This example has been tested with STMicroelectronics STM32F411E-Discovery
boards and can be easily tailored to any other supported device
and development board.
- STM32F411E-Discovery Set-up
- Use LED4, LED3, LED 5, LED6 connected respectively to PD.12, PD13, PD.14 & PD15 pins.
* LED5 (RED) will be ON if initialization fails.
* LED6 (BLUE) will toggle waiting for user to launch test, then be turn OFF
* LED6 (BLUE) will toggle while executing RTC wakeup callback in any mode.
* LED4 (GREEN) will be ON while returning from STANDBY mode (PWR flag check callback)
- Use USER Button connected to PA.00 pin.
- Connect an amperemeter to jumper JP2 to measure the IDD current
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
3d6be4bd40