/**
@page RCC_ClockConfig RCC Clock Config example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file RCC/RCC_ClockConfig/readme.txt
* @author MCD Application Team
* @brief Description of the RCC Clock Config example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
This example describes how to use the RCC HAL API to configure the system clock (SYSCLK)
and modify the clock settings in Run mode.
In this example, after startup SYSCLK is configured to the max frequency using the PLL with
HSE as clock source, the EVAL board Key button (connected to EXTI Line15) will be
used to change the PLL source: from HSE to HSI, and vice versa.
Each time the Key button is pressed; EXTI Line15 interrupt is generated and in the ISR
the PLL oscillator source is checked using __HAL_RCC_GET_PLL_OSCSOURCE() macro:
1- If the HSE oscillator is selected as PLL source, the following steps will be followed to switch
the PLL source to HSI oscillator:
a- Switch the system clock source to HSE to allow modification of the PLL configuration
b- Enable HSI Oscillator, select it as PLL source and finally activate the PLL
c- Select the PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
d- Disable the HSE oscillator (optional, if the HSE is no more needed by the application)
2- If the HSI oscillator is selected as PLL source, the following steps will be followed to switch
the PLL source to HSE oscillator:
a- Switch the system clock source to HSI to allow modification of the PLL configuration
b- Enable HSE Oscillator, select it as PLL source and finally activate the PLL
c- Select the PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
d- Disable the HSI oscillator (optional, if the HSI is no more needed by the application)
In this example the SYSCLK divided by 2 is outputted on the MCO2 pin(PC9).
@note The selected clock to output onto MCO must not exceed 100 MHz (the maximum I/O speed).
@note The SysTick 1 msec interrupt is required for the HAL process (Timeout management); by default
the configuration is done using the HAL_Init() API, and when the system clock configuration
is updated the SysTick configuration will be adjusted by the HAL_RCC_ClockConfig() API.
Three LEDs are toggled with a timing defined by the HAL_Delay() API.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
RCC, System, Clock Configuration, HSE bypass mode, HSI, System clock, Oscillator, PLL
@par Directory contents
- RCC/RCC_ClockConfig/Inc/stm32f4xx_hal_conf.h HAL configuration file
- RCC/RCC_ClockConfig/Inc/stm32f4xx_it.h Interrupt handlers header file
- RCC/RCC_ClockConfig/Inc/main.h Main program header file
- RCC/RCC_ClockConfig/Src/stm32f4xx_it.c Interrupt handlers
- RCC/RCC_ClockConfig/Src/main.c Main program
- RCC/RCC_ClockConfig/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
@par Hardware and Software environment
- This example runs on STM32F407xx/417xx devices.
- This example has been tested with STMicroelectronics STM324xG-EVAL RevC
evaluation boards and can be easily tailored to any other supported device
and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
83778d5c95