/**
@page CRC_Example Cyclic Redundancy Check Example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file CRC/CRC_Example/readme.txt
* @author MCD Application Team
* @brief Description of Cyclic Redundancy Check Example.
******************************************************************************
*
* Copyright (c) 2017 STMicroelectronics. All rights reserved.
*
* This software component is licensed by ST under BSD 3-Clause license,
* the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
@endverbatim
@par Example Description
This example guides you through the different configuration steps by means of the
HAL API. The CRC (Cyclic Redundancy Check) calculation unit computes the CRC code
of a given buffer of 32-bit data words, using a fixed generator polynomial (0x4C11DB7).
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 100 MHz.
The CRC peripheral configuration is ensured by HAL_CRC_Init() function.
The latter is calling HAL_CRC_MspInit() function which core is implementing
the configuration of the needed CRC resources according to the used hardware (CLOCK).
You can update HAL_CRC_Init() input parameters to change the CRC configuration.
The calculated CRC code is stored in uwCRCValue variable
and compared with the expected one stored in uwExpectedCRCValue variable.
STM32 Eval board LEDs are used to monitor the example status:
- LED1 (GREEN) is ON when a correct CRC value is calculated
- LED3 (RED) is ON when an incorrect CRC value is calculated or when there is an initialization error.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Security, CRC, CRC Polynomial, IEC 60870-5, hardware CRC
@par Directory contents
- CRC/CRC_Example/Inc/stm32f4xx_hal_conf.h HAL configuration file
- CRC/CRC_Example/Inc/stm32f4xx_it.h Interrupt handlers header file
- CRC/CRC_Example/Inc/main.h Header for main.c module
- CRC/CRC_Example/Src/stm32f4xx_it.c Interrupt handlers
- CRC/CRC_Example/Src/main.c Main program
- CRC/CRC_Example/Src/stm32f4xx_hal_msp.c HAL MSP module
- CRC/CRC_Example/Src/system_stm32f4xx.c STM32F4xx system source file
@par Hardware and Software environment
- This example runs on STM32F412xG devices.
- This example has been tested with an STMicroelectronics STM32412G-DISCOVERY
board and can be easily tailored to any other supported device
and development board.
@par How to use it ?
In order to make the program work, you must do the following:
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
d599a824df