81 lines
3.3 KiB
Plaintext
81 lines
3.3 KiB
Plaintext
/**
|
|
@page ADC_RegularConversion_Polling conversion using Polling
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file ADC/ADC_RegularConversion_Polling/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the ADC RegularConversion Polling example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to use the ADC in Polling mode to convert data through the HAL API.
|
|
|
|
When the end of conversion occurs, the converted data of ADC1 DR register is
|
|
affected to the uhADCxConvertedValue variable.
|
|
|
|
Note that the test carries out only one conversion. To trigger another conversion, the user
|
|
needs to reset then restart the example execution.
|
|
|
|
|
|
Use an external power supply, adjust supply voltage and connect it to pin PC0 (Arduino connector CN9 pin 3).
|
|
This allows to modify ADC_CHANNEL_10 voltage.
|
|
|
|
The converted value is monitored through debugger: uhADCxConvertedValue variable.
|
|
|
|
STM32 board LED can be used to monitor the conversion:
|
|
- LED3 is ON when there is an error occurs.
|
|
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Analog, ADC, Analog to Digital Converter, Regular Conversion, Polling, Single Conversion
|
|
|
|
@par Directory contents
|
|
|
|
- ADC/ADC_RegularConversion_Polling/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- ADC/ADC_RegularConversion_Polling/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- ADC/ADC_RegularConversion_Polling/Inc/main.h Header for main.c module
|
|
- ADC/ADC_RegularConversion_Polling/Src/stm32f4xx_it.c Interrupt handlers
|
|
- ADC/ADC_RegularConversion_Polling/Src/main.c Main program
|
|
- ADC/ADC_RegularConversion_Polling/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- ADC/ADC_RegularConversion_Polling/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F413xx/STM32F423xx devices.
|
|
|
|
- This example has been tested with STM32F413ZH-Nucleo board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|