126 lines
6.7 KiB
Plaintext
126 lines
6.7 KiB
Plaintext
/**
|
|
@page EEPROM_Emulation application to show an eeprom emulation
|
|
|
|
@verbatim
|
|
******************* (C) COPYRIGHT 2017 STMicroelectronics ********************
|
|
* @file EEPROM/EEPROM_Emulation/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the EEPROM_Emulation application.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Application Description
|
|
|
|
This application describes the software solution for substituting standalone EEPROM
|
|
by emulating the EEPROM mechanism using the on-chip Flash of STM32F4xx devices.
|
|
|
|
Please refer to AN3969 for further details regarding this application.
|
|
|
|
The application requires two Flash memory sectors of identical size allocated to non-volatile data:
|
|
one that is initially erased, and offers byte-by-byte programmability; the other that is ready
|
|
to take over when the former sector needs to be garbage-collected. A header field that occupies
|
|
the first half word (16-bit) of each sector indicates the sector status. Each of these sectors is
|
|
considered as a page.
|
|
The sectors used are Sector 2 and Sector 3 with a size of 16KB each one.
|
|
|
|
STM32F401xEx-Nucleo's LED can be used to monitor the application status:
|
|
- LED2 is On when the application runs successfully.
|
|
- LED2 is toggle in case of error.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
EEPROM, Emulation, Flash, Program, Erase, Sectors, OPCODE
|
|
|
|
@par Directory contents
|
|
|
|
- EEPROM/EEPROM_Emulation/Inc/stm32f4xx_hal_conf.h HAL Configuration file
|
|
- EEPROM/EEPROM_Emulation/Inc/main.h Header for main.c module
|
|
- EEPROM/EEPROM_Emulation/Inc/eeprom.h Header for eeprom.c module
|
|
- EEPROM/EEPROM_Emulation/Inc/stm32f4xx_it.h Header for stm32f4xx_it.c
|
|
- EEPROM/EEPROM_Emulation/Src/main.c Main program
|
|
- EEPROM/EEPROM_Emulation/Src/eeprom.c EEPROM program
|
|
- EEPROM/EEPROM_Emulation/Src/stm32f4xx_it.c Interrupt handlers
|
|
- EEPROM/EEPROM_Emulation/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This application runs on STM32F401xEx devices.
|
|
|
|
- This application has been tested with STMicroelectronics STM32F4xx-Nucleo RevB
|
|
boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
Table 1. EEPROM application implementation on STM32F4xx-Nucleo
|
|
/*** Platform ***|************* Implementation **************************|***** Configuration *****\
|
|
****************************************************************************************************
|
|
| Firmware | The EEPROM program is located at 0x08000000. The Flash| |
|
|
| | routines (program/erase) are executed from the Flash | |
|
|
| | memory. | |
|
|
| | The size of this program is about 6 Kbytes and | |
|
|
| | programmed on: | Sector 0 |
|
|
| | ------------------------------------------------------|-------------------------|
|
|
| | | |
|
|
| | The flash zone used for the EEPROM emulation is | Sector 2 and Sector 3 |
|
|
| | located at 0x08008000 | each one has a size of |
|
|
| | | 16KB |
|
|
\**************************************************************************************************/
|
|
|
|
@note
|
|
Before using the application, ensure that dedicated sectors for EEPROM (FLASH_SECTOR_2 and FLASH_SECTOR_3)
|
|
are erased to avoid a match with a valid page OPCODE.
|
|
|
|
Following picture illustrates the situation in program memory:
|
|
|
|
Top Flash Memory address /-------------------------------------------\ 0x08100000
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| Sector 4 - Sector 11 |
|
|
| |
|
|
|-------------------------------------------| 0x08010000
|
|
Sector 3 (16KB) | |
|
|
| |
|
|
| Flash used for EEPROM emulation mechanism | 0x0800C000
|
|
Sector 2 (16KB) | |
|
|
| |
|
|
|-------------------------------------------| 0x08008000
|
|
Sector 1 (16KB) | |
|
|
| |
|
|
|-------------------------------------------| 0x08004000
|
|
| |
|
|
Sector 0 (32KB) | flash used for implement the EEPROM |
|
|
| emulation mechanism(6KB) |
|
|
\-------------------------------------------/ 0x08000000
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the application
|
|
|
|
|
|
*/
|