/**
@page FSMC_SRAM FSMC SRAM basic functionalities use example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file FSMC/FSMC_SRAM/readme.txt
* @author MCD Application Team
* @brief Description of the FSMC SRAM basic functionalities use example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
This example describes how to configure the FSMC controller to access the SRAM
memory.
This example guides you through the different configuration steps by mean of HAL API
to configure the FMC controller to access the IS61WV102416BLL-10MLI SRAM mounted
on STM324xG-EVAL evaluation board.
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 168 MHz.
The goal of this example is to explain the different steps to configure the FMC
and make the SRAM device ready for access, without using the MSP layer.
In this example, the SRAM device is configured and initialized explicitly
following all initialization sequence steps. After initializing the device, user
can perform read/write operations on it. A data buffer is written to the SRAM
memory, then read back and checked to verify its correctness.
The user can chose his own configuration by commenting/uncommenting the defines for
undesired/desired configurations , for example, to enable Continuous clock feature,
uncomment the define for the configuration "FMC_CONTINUOUS_CLOCK_SYNC_ASYNC" in "main.h".
If the data is read correctly from SRAM, the LED1 is ON, otherwise the LED2 is ON.
LED3 is ON when there is an error in initialization.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Memory, FSMC, SRAM, Read, Write, Initialization, Access
@par Directory contents
- FSMC/FSMC_SRAM/Inc/stm32f4xx_hal_conf.h HAL Configuration file
- FSMC/FSMC_SRAM/Inc/main.h Main program header file
- FSMC/FSMC_SRAM/Inc/stm32f4xx_it.h Interrupt handlers header file
- FSMC/FSMC_SRAM/Src/main.c Main program
- FSMC/FSMC_SRAM/Src/stm32f4xx_hal_msp.c HAL MSP module
- FSMC/FSMC_SRAM/Src/stm32f4xx_it.c Interrupt handlers
- FSMC/FSMC_SRAM/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
@par Hardware and Software environment
- This example runs on STM32F407xx/417xx devices.
- This example has been tested with STMicroelectronics STM324xG-EVAL RevC
evaluation boards and can be easily tailored to any other supported device
and development board.
- STM324xG-EVAL RevC Set-up
- Please ensure that the jumper JP10 is not fitted in the position 2-3.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
83778d5c95