82 lines
3.2 KiB
Plaintext
82 lines
3.2 KiB
Plaintext
/**
|
|
@page DAC_SignalsGeneration DAC Signals generation example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file DAC/DAC_SignalsGeneration/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the DAC Signals generation example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example provides a short description of how to use the DAC peripheral to
|
|
generate several signals using DMA controller.
|
|
|
|
When the user presses the KEY push-button, DMA transfers the two selected
|
|
waveforms to the DAC.
|
|
For each press on KEY button, a signal has been selected and can be monitored on
|
|
the DAC channel one:
|
|
- Triangle waveform (Channel 1).
|
|
- Escalator waveform (Channel 1).
|
|
|
|
STM32 Eval boards LEDs can be used to monitor the transfer status:
|
|
- LED3 is ON when there are an error in initialization.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Keywords
|
|
|
|
Analog, DAC, Signals generation, DMA, Triangle, Escalator, Waveform, Amplitude
|
|
|
|
@par Directory contents
|
|
|
|
- DAC/DAC_SignalsGeneration/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- DAC/DAC_SignalsGeneration/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- DAC/DAC_SignalsGeneration/Inc/main.h Main program header file
|
|
- DAC/DAC_SignalsGeneration/Src/stm32f4xx_it.c Interrupt handlers
|
|
- DAC/DAC_SignalsGeneration/Src/main.c Main program
|
|
- DAC/DAC_SignalsGeneration/Src/stm32f4xx_hal_msp.c HAL MSP module
|
|
- DAC/DAC_SignalsGeneration/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F40xxx/STM32F41xxx devices.
|
|
|
|
- This example has been tested with STM324xG-EVAL evaluation board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM324xG-EVAL RevC Set-up
|
|
- Use KEY push-button connected to PC13.
|
|
- Connect PA4 (DAC Channel1) pin to an oscilloscope.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|