/**
@page ADC_RegularConversion_Polling ADC Regular Conversion Polling example.
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file ADC/ADC_RegularConversion_Polling/readme.txt
* @author MCD Application Team
* @brief Description of the ADC Regular Conversion Polling example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to use the ADC in Polling mode to convert data through the HAL API.
This example describes how to use the ADC3 and Polling to convert data from
ADC3 channel8.
When an end of conversion occurs the converted data of ADC3 DR register is
affected to the uhADCxConvertedValue variable .
The user can use the debugger's watch to evaluate uhADCxConvertedValue.
In this example, the system clock is 144MHz, APB2 = 72MHz and ADC clock = APB2/2.
Since ADC3 clock is 36 MHz and sampling time is set to 3 cycles, the conversion
time to 12bit data is 12 cycles so the total conversion time is (12+3)/36= 0.41us(2.4Msps).
User can vary the ADC3 channel7(for STM324xG-EVAL) voltage using the Eval Board potentiometer.
STM32 Eval boards LEDs can be used to monitor the transfer status:
- LED3 is ON when there are an error in initialization.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Keywords
Analog, ADC, Analog to Digital Converter, Regular Conversion, Polling, Single Conversion
@par Directory contents
- ADC/ADC_RegularConversion_Polling/Inc/stm32f4xx_hal_conf.h HAL configuration file
- ADC/ADC_RegularConversion_Polling/Inc/stm32f4xx_it.h Interrupt handlers header file
- ADC/ADC_RegularConversion_Polling/Inc/main.h Main program header file
- ADC/ADC_RegularConversion_Polling/Src/stm32f4xx_it.c Interrupt handlers
- ADC/ADC_RegularConversion_Polling/Src/main.c Main program
- ADC/ADC_RegularConversion_Polling/Src/stm32f4xx_hal_msp.c HAL MSP module
- ADC/ADC_RegularConversion_Polling/Src/system_stm32f4xx.c STM32F4xx system clock configuration file
@par Hardware and Software environment
- This example runs on STM32F407xx/417xx devices.
- This example has been tested with STM324xG-EVAL RevC evaluation board and can be
easily tailored to any other supported device and development board.
- STM324xG-EVAL RevC Set-up
- Use the Potentiometer (RV1) of the Eval board (connected to PF.09).
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
83778d5c95