/**
@page I2C_TwoBoards_ComPolling I2C Two Boards Communication Polling Example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file I2C/I2C_TwoBoards_ComPolling/readme.txt
* @author MCD Application Team
* @brief Description of the I2C Two Boards Communication Polling example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to handle I2C data buffer transmission/reception between two boards,
in polling mode.
_________________________ _________________________
| __________________| |_________________ |
| | I2C1 | | I2C1 | |
| | | | | |
| | CN5.D15 SCL(PB8)|______________________|(PB8)SCL CN5.D15 | |
| | | | | |
| | | | | |
| | | | | |
| | CN5.D14 SDA(PB9)|______________________|(PB9)SDA CN5.D14 | |
| | | | | |
| |__________________| |_________________| |
| __ | | __ |
| |__| | | |__| |
| USER GND|______________________|GND USER |
| | | |
|__STM32F469I_DISCOVERY___| |__STM32F469I_DISCOVERY___|
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 180 MHz.
The I2C peripheral configuration is ensured by the HAL_I2C_Init() function.
This later is calling the HAL_I2C_MspInit()function which core is implementing
the configuration of the needed I2C resources according to the used hardware (CLOCK,
GPIO). You may update this function to change I2C configuration.
The I2C communication is then initiated.
The project is split in two parts: the Master Board and the Slave Board
- Master Board
The HAL_I2C_Master_Receive() and the HAL_I2C_Master_Transmit() functions
allow respectively the reception and the transmission of a predefined data buffer
in Master mode.
- Slave Board
The HAL_I2C_Slave_Receive() and the HAL_I2C_Slave_Transmit() functions
allow respectively the reception and the transmission of a predefined data buffer
in Slave mode.
The user can choose between Master and Slave through "#define MASTER_BOARD"
in the "main.c" file:
- Uncomment "#define MASTER_BOARD" to select Master board.
- Comment "#define MASTER_BOARD" to select Slave board.
For this example the aTxBuffer is predefined and the aRxBuffer size is same as aTxBuffer.
In a first step after the user press the User push-button on the Master Board,
I2C Master starts the communication by sending aTxBuffer through HAL_I2C_Master_Transmit()
to I2C Slave which receives aRxBuffer through HAL_I2C_Slave_Receive().
The second step starts when the user press the User push-button on the Master Board,
the I2C Slave sends aTxBuffer through HAL_I2C_Slave_Transmit()
to the I2C Master which receives aRxBuffer through HAL_I2C_Master_Receive().
The end of this two steps are monitored through the HAL_I2C_GetState() function
result.
Finally, aTxBuffer and aRxBuffer are compared through Buffercmp() in order to
check buffers correctness.
STM32469I-DISCOVERY's LEDs can be used to monitor the transfer status:
- LED1 is ON when the transmission process is complete.
- LED1 is OFF when the reception process is complete.
- LED3 is ON when there is an error in transmission/reception process.
@note I2Cx instance used and associated resources can be updated in "main.h"
file depending hardware configuration used.
@note Timeout is set to 10 Seconds which means that if no communication occurs
during 10 Seconds, a Timeout Error will be generated.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@note The connection of the LCD reset pin to a dedicated GPIO PH7 instead of the STM32F469 NRST pin may cause residual display on LCD with applications/examples that do not require display.
The LCD clear can be ensured by hardware through the boards power off/power on or by software calling the BSP_LCD_Reset() function.
@par Keywords
Connectivity, Communication, I2C, Polling, Master, Slave, Transmission, Reception, Fast mode plus
@par Directory contents
- I2C/I2C_TwoBoards_ComPolling/Inc/stm32f4xx_hal_conf.h HAL configuration file
- I2C/I2C_TwoBoards_ComPolling/Inc/stm32f4xx_it.h Interrupt handlers header file
- I2C/I2C_TwoBoards_ComPolling/Inc/main.h Header for main.c module
- I2C/I2C_TwoBoards_ComPolling/Src/stm32f4xx_it.c Interrupt handlers
- I2C/I2C_TwoBoards_ComPolling/Src/main.c Main program
- I2C/I2C_TwoBoards_ComPolling/Src/system_stm32f4xx.c STM32F4xx system source file
- I2C/I2C_TwoBoards_ComPolling/Src/stm32f4xx_hal_msp.c HAL MSP file
@par Hardware and Software environment
- This example runs on STM32F469xx devices.
- This example has been tested with STM32469I-DISCOVERY board and can be
easily tailored to any other supported device and development board.
-STM32469I-DISCOVERY Set-up
- Connect Master board PB8 connected to CN5.D15 to Slave Board PB8 connected to CN5.D15
- Connect Master board PB9 connected to CN5.D14 to Slave Board PB9 connected to CN5.D14
- Connect Master board GND to Slave Board GND
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
o Uncomment "#define MASTER_BOARD" and load the project in Master Board
o Comment "#define MASTER_BOARD" and load the project in Slave Board
- Run the example
*/
83778d5c95