106 lines
3.7 KiB
Plaintext
106 lines
3.7 KiB
Plaintext
/**
|
|
@page TIM_OnePulse TIM One Pulse example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file TIM/TIM_OnePulse/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the TIM One Pulse example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to use the TIM peripheral to generate a single pulse when
|
|
a rising edge of an external signal is received on the timer Input pin.
|
|
|
|
|
|
Clock setup for TIM5
|
|
================================
|
|
|
|
TIM5CLK = SystemCoreClock = 180 MHz.
|
|
|
|
Prescaler = (TIM5CLK /TIM5 counter clock) - 1
|
|
|
|
The prescaler value is computed in order to have TIM5 counter clock
|
|
set at 18000000 Hz.
|
|
|
|
The Autoreload value is 65535 (TIM5->ARR), so the maximum frequency value to
|
|
trigger the TIM5 input is 18000000/65535 [Hz].
|
|
|
|
Configuration of TIM5 in One Pulse Mode
|
|
===================================================
|
|
|
|
- The external signal is connected to TIM5_CH2 pin (PA.01),
|
|
and a rising edge on this input is used to trigger the Timer.
|
|
- The One Pulse signal is output on TIM5_CH1 (PA.00).
|
|
|
|
The delay value is fixed to:
|
|
- Delay = CCR1/TIM5 counter clock
|
|
= 16383 / 18000000 [sec]
|
|
|
|
The pulse value is fixed to :
|
|
- Pulse value = (TIM_Period - TIM_Pulse)/TIM5 counter clock
|
|
= (65535 - 16383) / 18000000 [sec]
|
|
|
|
The one pulse waveform can be displayed using an oscilloscope and it looks
|
|
like this.
|
|
|
|
____
|
|
| |
|
|
CH2 _________________________| |__________________________________________
|
|
|
|
___________________________
|
|
| |
|
|
CH1 ______________________________________| |_____
|
|
<---Delay----><------Pulse--------------->
|
|
|
|
|
|
@par Keywords
|
|
|
|
Timers, Output, signals, One Pulse, PWM, Oscilloscope, External signal, Autoreload, Waveform
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_OnePulse/Inc/stm32f4xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_OnePulse/Inc/stm32f4xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_OnePulse/Inc/main.h Header for main.c module
|
|
- TIM/TIM_OnePulse/Src/stm32f4xx_it.c Interrupt handlers
|
|
- TIM/TIM_OnePulse/Src/main.c Main program
|
|
- TIM/TIM_OnePulse/Src/stm32f4xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_OnePulse/Src/system_stm32f4xx.c STM32F4xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F446xx devices.
|
|
- In this example, the clock is set to 180 MHz.
|
|
|
|
- This example has been tested with STM32446E-EVAL board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM32446E-EVAL Set-up
|
|
- Connect the external signal to the TIM5_CH2 pin (PA.01) ()
|
|
- Connect the TIM5_CH1 pin(PA.00) () to an oscilloscope to monitor the waveform.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files: Project->Rebuild all
|
|
- Load project image: Project->Download and Debug
|
|
- Run program: Debug->Go(F5)
|
|
|
|
|
|
*/
|