115 lines
4.8 KiB
Plaintext
115 lines
4.8 KiB
Plaintext
/**
|
|
@page IWDG_Reset Independent Watchdog Reset Example
|
|
|
|
@verbatim
|
|
********************* COPYRIGHT(c) 2016 STMicroelectronics *******************
|
|
* @file IWDG/IWDG_Reset/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the IWDG Reset.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to handle the IWDG reload counter and simulate a software fault that generates
|
|
an MCU IWDG reset after a preset laps of time.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 72 MHz.
|
|
|
|
The IWDG timeout is set to 1 second.
|
|
|
|
First, the TIM16 timer is configured to measure the LSI frequency as the
|
|
LSI is internally connected to TIM16 CH1, in order to adjust the IWDG clock.
|
|
The LSI frequency value could be monitored on debugger in "uwLsiFreq" variable.
|
|
|
|
The LSI measurement using the TIM16 is described below:
|
|
- Configure the TIM16 to remap internally the TIM16 CH1 Input Capture to the LSI
|
|
clock output.
|
|
- Enable the TIM16 Input Capture interrupt: after one cycle of LSI clock, the
|
|
period value is stored in a variable and compared to the HCLK clock to get
|
|
its real value.
|
|
|
|
Then, the IWDG reload counter is configured as below to obtain 1 second according
|
|
to the measured LSI frequency after setting the prescaler value:
|
|
|
|
IWDG counter clock Frequency = LSI Frequency / Prescaler value
|
|
|
|
The IWDG reload counter is refreshed each 990 ms in the main program infinite
|
|
loop to prevent a IWDG reset.
|
|
|
|
LED4 is also toggling each 990 ms indicating that the program is running.
|
|
|
|
An EXTI Line is connected to a GPIO pin, configured to generate an interrupt
|
|
when the User push-button (PA.00) is pressed.
|
|
|
|
The EXTI Line is used to simulate a software failure: once the EXTI Line event
|
|
occurs by pressing the User push-button (PA.00), the corresponding interrupt is served.
|
|
|
|
In the ISR, a write to invalid address generates a Hardfault exception
|
|
containing an infinite loop and preventing to return to main program (the IWDG
|
|
reload counter is not refreshed).
|
|
As a result, when the IWDG counter reaches 0, the IWDG reset occurs.
|
|
|
|
If the IWDG reset is generated, after the system resumes from reset, LED3 turns on for 4 seconds.
|
|
If the EXTI Line event does not occur, the IWDG counter is indefinitely refreshed in the main
|
|
program infinite loop, and there is no IWDG reset.
|
|
|
|
If the user button is pressed while LED3 is turned on, another Hardfault exception is triggered.
|
|
In this case, since the IWDG has not been reprogrammed yet, the software ends up
|
|
stuck in the hardfault. All LEDs are turned off in this situation.
|
|
|
|
LED5 will turn on if any error occurs.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in SysTick ISR. This
|
|
implies that if HAL_Delay() is called from a peripheral ISR process, then
|
|
the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- IWDG/IWDG_Reset/Inc/stm32f3xx_hal_conf.h HAL configuration file
|
|
- IWDG/IWDG_Reset/Inc/stm32f3xx_it.h Interrupt handlers header file
|
|
- IWDG/IWDG_Reset/Inc/main.h Header for main.c module
|
|
- IWDG/IWDG_Reset/Src/stm32f3xx_it.c Interrupt handlers
|
|
- IWDG/IWDG_Reset/Src/main.c Main program
|
|
- IWDG/IWDG_Reset/Src/stm32f3xx_hal_msp.c HAL MSP file
|
|
- IWDG/IWDG_Reset/Src/system_stm32f3xx.c STM32F3xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F303xC devices.
|
|
|
|
- This example has been tested with STM32F3-Discovery RevB board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
|
|
*/
|
|
|