94 lines
4.4 KiB
Plaintext
94 lines
4.4 KiB
Plaintext
/**
|
|
@page RCC_ClockConfig RCC Clock Config example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
|
* @file RCC/RCC_ClockConfig/Readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the RCC Clock Config example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2017 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of the system clock (SYSCLK) and modification of the clock settings in Run mode, using the RCC HAL API.
|
|
|
|
In this example, after startup SYSCLK is configured to the max frequency using the PLL with
|
|
HSE as clock source, the EVAL board Key button (connected to EXTI Line15) will be
|
|
used to change the PLL source: from HSE to HSI, and vice versa.
|
|
Each time the Key button is pressed; EXTI Line15 interrupt is generated and in the ISR
|
|
the PLL oscillator source is checked using __HAL_RCC_GET_PLL_OSCSOURCE() macro:
|
|
|
|
1- If the HSE oscillator is selected as PLL source, the following steps will be followed to switch
|
|
the PLL source to HSI oscillator:
|
|
a- Switch the system clock source to HSE to allow modification of the PLL configuration
|
|
b- Enable HSI Oscillator, select it as PLL source and finally activate the PLL
|
|
c- Select the PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
|
|
d- Disable the HSE oscillator (optional, if the HSE is no more needed by the application)
|
|
|
|
2- If the HSI oscillator is selected as PLL source, the following steps will be followed to switch
|
|
the PLL source to HSE oscillator:
|
|
a- Switch the system clock source to HSI to allow modification of the PLL configuration
|
|
b- Enable HSE Oscillator, select it as PLL source and finally activate the PLL
|
|
c- Select the PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers
|
|
d- Disable the HSI oscillator (optional, if the HSI is no more needed by the application)
|
|
|
|
In this example the SYSCLK divided by 2 is outputted on the MCO2 pin(PC9).
|
|
|
|
@note The selected clock to output onto MCO must not exceed 100 MHz (the maximum I/O speed).
|
|
@note The SysTick 1 msec interrupt is required for the HAL process (Timeout management); by default
|
|
the configuration is done using the HAL_Init() API, and when the system clock configuration
|
|
is updated the SysTick configuration will be adjusted by the HAL_RCC_ClockConfig() API.
|
|
|
|
Three LEDs are toggled with a timing defined by the HAL_Delay() API.
|
|
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- RCC/RCC_ClockConfig/Inc/stm32f2xx_hal_conf.h HAL configuration file
|
|
- RCC/RCC_ClockConfig/Inc/stm32f2xx_it.h Interrupt handlers header file
|
|
- RCC/RCC_ClockConfig/Inc/main.h Main program header file
|
|
- RCC/RCC_ClockConfig/Src/stm32f2xx_it.c Interrupt handlers
|
|
- RCC/RCC_ClockConfig/Src/main.c Main program
|
|
- RCC/RCC_ClockConfig/Src/system_stm32f2xx.c STM32F2xx system clock configuration file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F207xx/217xx device.
|
|
|
|
- This example has been tested with STMicroelectronics STM322xG-EVAL
|
|
evaluation boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|