/**
@page I2C_TwoBoards_AdvComIT I2C Two Boards Advanced Communication IT example
@verbatim
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
* @file I2C/I2C_TwoBoards_AdvComIT/Readme.txt
* @author MCD Application Team
* @brief Description of the I2C Two Boards Advanced Communication with
* Interrupt example.
******************************************************************************
* @attention
*
* Copyright (c) 2017 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to handle I2C data buffer transmission/reception between two boards,
using an interrupt.
_________________________ _________________________
| ______________| |______________ |
| | I2C1 | | I2C1| |
| | | | | |
| | SCL(PB6)|______________________|(PB6)SCL | |
| | | | | |
| | | | | |
| | | | | |
| | SDA(PB9)|______________________|(PB9)SDA | |
| | | | | |
| |______________| |______________| |
| __ | | __ |
| |__| | | |__| |
| KEY | | KEY |
| GND|______________________|GND |
|_STM32F2 ________________| |_________________STM32F2_|
This example guides you through the different configuration steps by mean of HAL API
to ensure I2C Data buffer transmission and reception using Interrupt.
The communication is done with 2 Boards through I2C and using the following I2C features:
- 7-bit addressing mode
- Fast speed mode (400KHz)
- Interrupting capability
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 120 MHz.
The I2C peripheral configuration is ensured by the HAL_I2C_Init() function.
This later is calling the HAL_I2C_MspInit()function which implements
the configuration of the needed I2C resources according to the used hardware (CLOCK,
GPIO and NVIC). You may update this function to change I2C configuration.
The I2C communication is then initiated.
The project is split in two parts the Master Board and the Slave Board
- Master Board
The HAL_I2C_Master_Receive_IT() and the HAL_I2C_Master_Transmit_IT() functions
allow respectively the reception and the transmission of a predefined data buffer
in Master mode using interrupt.
- Slave Board
The HAL_I2C_Slave_Receive_IT() and the HAL_I2C_Slave_Transmit_IT() functions
allow respectively the reception and the transmission of a predefined data buffer
in Slave mode using interrupt.
The user can choose between Master and Slave through "#define MASTER_BOARD"
in the "main.c" file:
- Uncomment "#define MASTER_BOARD" to select Master board.
- Comment "#define MASTER_BOARD" to select Slave board.
For this example two buffers are used
- aTxBuffer buffer is used to save the data to be transmitted
- aRxBuffer buffer is used to save the received data
Note that the two buffers have the same size
In Master board side:
- Wait user button to be pressed (used for only synchronization at startup)
- Requests write operation by sending specific command "MASTER_REQ_WRITE" to Slave
- Sends the number of data to be written
- Transmits aTxBuffer buffer to slave
- Requests read operation by sending specific command "MASTER_REQ_READ" to Slave
- Sends the number of data to be read
- Receives data from Slave in aRxBuffer
- Checks the correctness of data and Toggle LED1 when data is received correctly
otherwise it turns ON LED2 and communication is stopped (using infinite loop)
In Slave board side:
- Receives request from Master
- Receives the request operation from Master and depending on the operation type (write or read):
- If Master requests write operation:
- Receives number of data to be written by Master
- Receives data from master in aRxBuffer
- Checks the correctness of data and Toggle LED1 when data is received correctly
otherwise it turns ON LED2 and communication is stopped (using infinite loop)
- If Master requests read operation:
- Receives number of data to be written to Master
- Transmits aTxBuffer buffer to master
These operations are repeated periodically and the start of communication is triggered
by pushing the user button of the Master board.
@note In Master side, only Acknowledge failure error is handled. When this error
occurs Master restart the current operation until Slave acknowledges it's
address.
@note I2Cx instance used and associated resources can be updated in "main.h"
file depending hardware configuration used.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- I2C/I2C_TwoBoards_AdvComIT/Inc/stm32f2xx_hal_conf.h HAL configuration file
- I2C/I2C_TwoBoards_AdvComIT/Inc/stm32f2xx_it.h I2C interrupt handlers header file
- I2C/I2C_TwoBoards_AdvComIT/Inc/main.h Header for main.c module
- I2C/I2C_TwoBoards_AdvComIT/Src/stm32f2xx_it.c I2C interrupt handlers
- I2C/I2C_TwoBoards_AdvComIT/Src/main.c Main program
- I2C/I2C_TwoBoards_AdvComIT/Src/system_stm32f2xx.c STM32F2xx system source file
- I2C/I2C_TwoBoards_AdvComIT/Src/stm32f2xx_hal_msp.c HAL MSP file
@par Hardware and Software environment
- This example runs on STM32F217xx devices.
- This example has been tested with STM322xG-EVAL RevC board and can be
easily tailored to any other supported device and development board.
- STM322xG-EVAL Set-up
- Connect Master board PB6 to Slave Board PB6 (pin 13 connector CN4)
- Connect Master board PB9 to Slave Board PB9 (pin 8 connector CN4)
- Connect Master board GND to Slave Board GND
- Check that a pull-up resistor is connected on one I2C SDA pin
- Check that a pull-up resistor is connected on one I2C SCL pin
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
o Uncomment "#define MASTER_BOARD" and load the project in Master Board
o Comment "#define MASTER_BOARD" and load the project in Slave Board
- Run the example
*/
63e02baff3