100 lines
4.4 KiB
Plaintext
100 lines
4.4 KiB
Plaintext
/**
|
||
@page FatFs_USBDisk FatFs with USB disk drive application
|
||
|
||
@verbatim
|
||
******************** (C) COPYRIGHT 2017 STMicroelectronics *******************
|
||
* @file FatFs/FatFs_USBDisk/readme.txt
|
||
* @author MCD Application Team
|
||
* @brief Description of the FatFs with USB disk drive application
|
||
******************************************************************************
|
||
* @attention
|
||
*
|
||
* Copyright (c) 2017 STMicroelectronics.
|
||
* All rights reserved.
|
||
*
|
||
* This software is licensed under terms that can be found in the LICENSE file
|
||
* in the root directory of this software component.
|
||
* If no LICENSE file comes with this software, it is provided AS-IS.
|
||
*
|
||
******************************************************************************
|
||
@endverbatim
|
||
|
||
@par Application Description
|
||
|
||
How to use STM32Cube firmware with FatFs middleware component as a generic FAT
|
||
file system module and STM32 USB On-The-Go (OTG) host library, in both Full
|
||
Speed (FS) and High Speed (HS) modes. This example develops an application
|
||
exploiting FatFs features, with USB disk drive configuration.
|
||
|
||
At the beginning of the main program the HAL_Init() function is called to reset
|
||
all the peripherals, initialize the Flash interface and the systick.
|
||
The user is provided with the SystemClock_Config() function to configure the system
|
||
clock (SYSCLK) to run at 120 MHz. The Full Speed (FS) USB module uses internally
|
||
a 48-MHz clock.
|
||
|
||
The application is based on writing a text file to a drive, and it's performed
|
||
using FatFs APIs to access the FAT volume as described in the following steps:
|
||
|
||
- Link the USB Host disk I/O driver;
|
||
- Register the file system object (mount) to the FatFs module for the USB drive;
|
||
- Create and Open new text file object with write access;
|
||
- Write data to the text file;
|
||
- Close the open text file;
|
||
- Unlink the USB Host disk I/O driver.
|
||
|
||
Notice that the application manages possible errors that might occur during the
|
||
access to FAT volume, when using FatFs APIs. In addition, user can check if the
|
||
written text file is available on the USB disk.
|
||
|
||
It is possible to fine tune needed FatFs features by modifying defines values
|
||
in FatFs configuration file <20>ffconf.h<> available under the project includes
|
||
directory, in a way to fit the application requirements.
|
||
|
||
NUCLEO-207ZG Rev.B board's LEDs can be used to monitor the application status:
|
||
- LED1 is ON when the application runs successfully.
|
||
- LED3 is ON when any error occurs.
|
||
|
||
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
||
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
||
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
||
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
||
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
||
|
||
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
|
||
to have correct HAL operation.
|
||
|
||
For more details about FatFs implementation on STM32Cube, please refer to UM1721 "Developing Applications
|
||
on STM32Cube with FatFs".
|
||
|
||
@par Directory contents
|
||
|
||
- FatFs/FatFs_USBDisk/Inc/stm32f2xx_hal_conf.h HAL configuration file
|
||
- FatFs/FatFs_USBDisk/Inc/stm32f2xx_it.h Interrupt handlers header file
|
||
- FatFs/FatFs_USBDisk/Inc/main.h Main program header file
|
||
- FatFs/FatFs_USBDisk/Inc/ffconf.h FAT file system module configuration file
|
||
- FatFs/FatFs_USBDisk/Src/stm32f2xx_it.c Interrupt handlers
|
||
- FatFs/FatFs_USBDisk/Src/main.c Main program
|
||
- FatFs/FatFs_USBDisk/Src/system_stm32f2xx.c STM32F2xx system clock configuration file
|
||
|
||
@par Hardware and Software environment
|
||
|
||
- This application runs on STM32F207xx devices.
|
||
|
||
- This application has been tested with STMicroelectronics NUCLEO-207ZG Rev.B board
|
||
and can be easily tailored to any other supported device and board.
|
||
|
||
- NUCLEO-207ZG Set-up
|
||
- Plug the USB key into the NUCLEO-207ZG Rev.B board through 'USB micro A-Male
|
||
to A-Female' cable.
|
||
|
||
- Make sure that the jumper JP4 is closed
|
||
|
||
@par How to use it ?
|
||
|
||
In order to make the program work, you must do the following :
|
||
- Open your preferred toolchain
|
||
- Rebuild all files and load your image into target memory
|
||
- Run the application
|
||
|
||
|
||
*/ |