98 lines
4.2 KiB
Plaintext
98 lines
4.2 KiB
Plaintext
/**
|
|
@page RTC_LSI RTC prescaler adjustment with LSI Measurements example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file RTC/RTC_LSI/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the RTC prescaler adjustment with LSI Measurements example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Use of the LSI clock source autocalibration to get a precise RTC clock.
|
|
In the associated software, the system clock is set to 72 MHz.
|
|
As an application example, it demonstrates how to configure the TIM5 timer
|
|
internally connected to LSI clock output, in order to adjust the RTC prescaler.
|
|
|
|
The Low Speed Internal (LSI) clock is used as RTC clock source.
|
|
After reset, the RTC prescaler is set with the default LSI frequency (40 kHz).
|
|
The RTC WakeUp is configured to generate an interrupt each 1s.
|
|
|
|
A key value is written in backup data register 1 to indicate if the wakeup timer has
|
|
already been enabled. If so the wakeup timer is disabled prior configuring the RTC
|
|
automatic wakeup.
|
|
|
|
LED1 is toggled inside the RTC WakeUp interrupt each 1s.
|
|
|
|
The inaccuracy of the LSI clock causes the RTC WakeUp Interrupt to be inaccurate.
|
|
The RTC CK_SPRE signal can be monitored by LED1 which is toggled into the RTC
|
|
Wakeup interrupt service routine.
|
|
|
|
The program waits until Key push-button is pressed to begin the auto calibration
|
|
procedure:
|
|
- Configure the TIM5 to remap internally the TIM5 TIM_CHANNEL_4
|
|
Input Capture to the LSI clock output.
|
|
- Enable the TIM5 Input Capture interrupt: after one cycle of LSI clock, the
|
|
period value is stored in a variable and compared to the HCLK clock to get
|
|
its real value.
|
|
- The RTC prescaler is adjusted with this LSI frequency value so that the RTC
|
|
CK_SPRE value become more accurate.
|
|
- When calibration is done the variable uwLsiFreq is visualized into the debugger
|
|
to indicate the end of this operation.
|
|
- The LSI value is updated and displayed on the debugger in uwLsiFreq variable.
|
|
|
|
- LED3 is On: This indicates that the system generates an error.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in SysTick ISR. This
|
|
implies that if HAL_Delay() is called from a peripheral ISR process, then
|
|
the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- RTC/RTC_LSI/Inc/stm32f1xx_conf.h Library Configuration file
|
|
- RTC/RTC_LSI/Inc/main.h header file for main.c
|
|
- RTC/RTC_LSI/Inc/stm32f1xx_it.h Header for stm32f1xx_it.c
|
|
- RTC/RTC_LSI/Src/system_stm32f1xx.c STM32F1xx system clock configuration file
|
|
- RTC/RTC_LSI/Src/stm32f1xx_it.c Interrupt handlers
|
|
- RTC/RTC_LSI/Src/main.c Main program
|
|
- RTC/RTC_LSI/Src/stm32f1xx_hal_msp.c HAL MSP module
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F107xC devices.
|
|
|
|
- This example has been tested with STM3210C-EVAL RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM3210C-EVAL RevC Set-up
|
|
- Use LED1 connected to PD.07 pin (pin 15 in CN8 connector).
|
|
- Use the Key push-button connected to pin PB.09 (EXTI_Line9-5)
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|