/**
@page PWR_CurrentConsumption PWR Current Consumption example
@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file PWR/PWR_CurrentConsumption/readme.txt
* @author MCD Application Team
* @brief Description of the PWR Current Consumption example.
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to configure the system to measure the current consumption in different
low-power modes.
The Low Power modes are:
- SLEEP mode
- STOP mode without RTC wake-up
- STOP mode with RTC wake-up
- STANDBY mode without RTC wake-up
- STANDBY mode with RTC wake-up
To run this example, user has to follow the following steps:
1. Select the low power modes to be measured by uncommenting the corresponding
line inside the stm32f0xx_lp_modes.h file.
@code
/* #define SLEEP_MODE */
/*#define STOP_MODE*/
#define STOP_RTC_MODE
/* #define STANDBY_MODE */
/* #define STANDBY_RTC_MODE */
@endcode
2. Use an external amperemeter to measure the IDD current.
3. This example can not be used in DEBUG mode, this is due to the fact that the
Cortex-M0 core is no longer clocked during low power mode so debugging
features are disabled.
4. Initial condition, wire GND to PA0 (connector CN7 : PIN28), for specific standby mode test case.
Here below a detailed description of the example code:
@verbatim
1. After reset, the program waits for User push-button connected to PC.13 pin
to be pressed - LED2 is blinking - to enter the selected low power mode.
- When the RTC is not used in the low power mode configuration, press
again the User push-button to exit the low power mode or, in standby mode wire VDD
to PA.00
- When the RTC is used, the wakeup from low power mode is automatically
generated by the RTC (after 20s).
2. After exit from low power mode, the LED2 is blinking.
In the case of exit from stand-by mode, LED2 is first ON for two seconds before
starting blinking.
3. The sequence can be repeated from step 1 in following the same steps (pressing
the USER button to enter the desired low power mode)
In case of error, LED2 is slowly blinking (1 sec. period).
Low power modes description:
- Sleep Mode
============
- System Running at PLL (48 MHz)
- Flash 1 wait state
- Instruction and Data caches ON
- Prefetch OFF
- Code running from Internal FLASH
- All peripherals disabled.
- Wakeup using EXTI Line (User push-button PC.13)
- STOP Mode
===========
- RTC Clocked by LSI
- Regulator in LP mode
- HSI, HSE OFF and LSI if not used as RTC Clock source
- No IWDG
- Wakeup using EXTI Line (User push-button PC.13)
- STOP Mode with RTC clocked by LSI
==========================================
- RTC Clocked by LSI
- Regulator in LP mode
- HSI, HSE OFF and LSI if not used as RTC Clock source
- No IWDG
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
- STANDBY Mode
==============
- RTC OFF
- IWDG and LSI OFF
- Wakeup using wakeup pin (wire Vdd to PA.00)
- STANDBY Mode with RTC clocked by LSI
==========================================
- RTC Clocked by LSI
- IWDG OFF and LSI OFF if not used as RTC Clock source
- Automatic Wakeup using RTC clocked by LSI (after ~20s)
@endverbatim
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_hal_conf.h HAL Configuration file
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_it.h Interrupt handlers header file
- PWR/PWR_CurrentConsumption/Inc/main.h Header for main.c module
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_lp_modes.h STM32F0xx Low Power Modes header file
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_it.c Interrupt handlers
- PWR/PWR_CurrentConsumption/Src/main.c Main program
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_hal_msp.c HAL MSP module
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_lp_modes.c STM32F0xx Low Power Modes source file
- PWR/PWR_CurrentConsumption/Src/system_stm32f0xx.c stm32f0xx system source file
@par Hardware and Software environment
- This example runs on STM32F091xC devices
- This example has been tested with STM32F091RC-Nucleo RevC board embedding
a STM32F091RCT6 device and can be
easily tailored to any other supported device and development board.
- STM32F091RC-Nucleo RevC Set-up
- Wire GND to PA0 (CN7, PIN28)
- Use LED2 connected to PA.05 pin.
* LED2 toggles while waiting for the USER push-button to be pressed to enter the low power mode.
- Connect an amperemeter to JP6 to measure the IDD current
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
a58188598c