97 lines
3.7 KiB
Plaintext
97 lines
3.7 KiB
Plaintext
/**
|
|
@page TIM_PWMOutput TIM PWM Output example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file TIM/TIM_PWMOutput/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWM signals generation using TIM1
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
Configuration of the TIM peripheral in PWM (pulse width modulation) mode.
|
|
|
|
SystemCoreClock is set to 48 MHz for STM32F0xx Devices.
|
|
|
|
In this example TIM1 input clock (TIM1CLK) is set to APB1 clock (PCLK1),
|
|
since APB1 prescaler is equal to 1.
|
|
TIM1CLK = PCLK1
|
|
PCLK1 = HCLK
|
|
=> TIM1CLK = HCLK = SystemCoreClock
|
|
|
|
To get TIM1 counter clock at 16 MHz, the prescaler is computed as follows:
|
|
Prescaler = (TIM1CLK / TIM1 counter clock) - 1
|
|
Prescaler = ((SystemCoreClock) /16 MHz) - 1
|
|
|
|
To get TIM1 output clock at 24 KHz, the period (ARR)) is computed as follows:
|
|
ARR = (TIM1 counter clock / TIM1 output clock) - 1
|
|
= 665
|
|
|
|
TIM1 Channel1 duty cycle = (TIM1_CCR1/ TIM1_ARR + 1)* 100 = 50%
|
|
TIM1 Channel2 duty cycle = (TIM1_CCR2/ TIM1_ARR + 1)* 100 = 37.5%
|
|
TIM1 Channel3 duty cycle = (TIM1_CCR3/ TIM1_ARR + 1)* 100 = 25%
|
|
TIM1 Channel4 duty cycle = (TIM1_CCR4/ TIM1_ARR + 1)* 100 = 12.5%
|
|
|
|
|
|
The PWM waveforms can be displayed using an oscilloscope.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
|
|
@par Directory contents
|
|
|
|
- TIM/TIM_PWMOutput/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- TIM/TIM_PWMOutput/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- TIM/TIM_PWMOutput/Inc/main.h Header for main.c module
|
|
- TIM/TIM_PWMOutput/Src/stm32f0xx_it.c Interrupt handlers
|
|
- TIM/TIM_PWMOutput/Src/main.c Main program
|
|
- TIM/TIM_PWMOutput/Src/stm32f0xx_hal_msp.c HAL MSP file
|
|
- TIM/TIM_PWMOutput/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F0xx devices.
|
|
- In this example, the clock is set to 48 MHz.
|
|
|
|
- This example has been tested with STMicroelectronics STM32072B-EVAL RevB
|
|
board and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
- STM32072B-EVAL RevB Set-up
|
|
Connect the following pins to an oscilloscope to monitor the different waveforms:
|
|
- TIM1_CH1 : PA.08 (pin 8 in CN7 connector)
|
|
- TIM1_CH2 : PA.09 (pin 7 in CN7 connector)
|
|
- TIM1_CH3 : PA.10 (pin 9 in CN7 connector)
|
|
- TIM1_CH4 : PA.11 (pin 12 in CN7 connector)
|
|
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|