97 lines
4.3 KiB
Plaintext
97 lines
4.3 KiB
Plaintext
/**
|
|
@page FLASH_WriteProtection FLASH write protection
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file FLASH/FLASH_WriteProtection/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the FLASH write protection example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to configure and use the FLASH HAL API to enable and disable the write
|
|
protection of the internal Flash memory.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system clock (SYSCLK)
|
|
to run at 48 MHz.
|
|
|
|
- If WRITE_PROTECTION_ENABLE is selected, the write protection will be enabled
|
|
for the defined sectors: FLASH_PAGE_TO_BE_PROTECTED.
|
|
To load the new option byte values, a system Reset is necessary, for this, the
|
|
function HAL_FLASH_OB_Launch() is used.
|
|
|
|
- If WRITE_PROTECTION_DISABLE is selected, the write protection will be enabled
|
|
for the defined sectors: FLASH_PAGE_TO_BE_PROTECTED.
|
|
To load the new option byte values, a system Reset is necessary, for this, the
|
|
function HAL_FLASH_OB_Launch() is used.
|
|
|
|
- Then an erase operation is done by filling the erase init structure giving the
|
|
starting erase page and the number of pages to erase. At this stage, all these
|
|
pages will be erased one by one separately.
|
|
|
|
@note: if problem occurs on a page, erase will be stopped and faulty page will
|
|
be returned to user (through variable 'PageError').
|
|
|
|
Once this operation is finished, word programming operation will be performed
|
|
in the Flash memory. The written data is then read back and checked.
|
|
|
|
STM32072B-EVAL board's LED can be used to monitor the transfer status:
|
|
- LED1 is ON when there are no errors detected after programming
|
|
=> should be the case when WRITE_PROTECTION_DISABLE flag is enabled
|
|
(or when both switches are disabled)
|
|
The following LEDs can be used to monitor the transfer status:
|
|
- LED2 is ON when there are errors detected after programming
|
|
=> should be the case when WRITE_PROTECTION_ENABLE flag is enabled
|
|
- LED3 is ON when there is an issue during erase, OB erase, program or OB program procedure
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in SysTick ISR. This
|
|
implies that if HAL_Delay() is called from a peripheral ISR process, then
|
|
the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- FLASH/FLASH_WriteProtection/Inc/stm32f0xx_hal_conf.h HAL Configuration file
|
|
- FLASH/FLASH_WriteProtection/Inc/stm32f0xx_it.h Header for stm32f0xx_it.c
|
|
- FLASH/FLASH_WriteProtection/Inc/main.h Header for main.c module
|
|
- FLASH/FLASH_WriteProtection/Src/stm32f0xx_it.c Interrupt handlers
|
|
- FLASH/FLASH_WriteProtection/Src/main.c Main program
|
|
- FLASH/FLASH_WriteProtection/Src/system_stm32f0xx.c STM32F0xx system clock configuration file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F072B devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32072B-EVAL RevB board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following:
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
|
|
*/
|