133 lines
5.7 KiB
Plaintext
133 lines
5.7 KiB
Plaintext
/**
|
|
@page Demo Demo STM32F091RC-Nucleo RevC
|
|
|
|
@verbatim
|
|
******************************************************************************
|
|
* @file readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of STM32F091RC-Nucleo RevC Demo
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Demo Description
|
|
|
|
Demonstration firmware based on STM32Cube. This example helps you to discover
|
|
STM32 Cortex-M devices that are plugged onto your STM32 Nucleo board.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system clock
|
|
(SYSCLK) to run at 48 MHz.
|
|
|
|
|
|
Below you find the sequence to discover the demonstration :
|
|
|
|
- Check the availability of adafruit 1.8" TFT shield on top of STM32 Nucleo
|
|
board. This is done by reading the state of IO PB.00 pin (mapped to JoyStick
|
|
available on adafruit 1.8" TFT shield). If the state of PB.00 is high then
|
|
the adafruit 1.8" TFT shield is available.
|
|
|
|
- Adafruit 1.8" TFT shield is not available:
|
|
LED2 is toggling with a first frequency equal to ~1Hz.
|
|
Pressing User button lets LED2 toggling with a second frequency equal to ~5Hz.
|
|
Pressing User button again, changes LED2 toggling frequency to ~10Hz.
|
|
This is done in an infinite loop.
|
|
|
|
- Adafruit 1.8" TFT shield is available:
|
|
LED2 is turned ON, because it's sharing the same pin with the SPI CLK signal
|
|
used to communicate with the Adafruit 1.8" TFT shield.
|
|
A menu will be displayed on TFT. Follow instructions below:
|
|
|
|
- Joystick DOWN to continue menu display
|
|
- Choose the desired display mode: Press Joystick DOWN for automatic mode
|
|
or Joystick UP for manual mode.
|
|
|
|
- Manual Mode selected:
|
|
Images available on SD Card, are displayed by pressing Joystick RIGHT
|
|
to display next image or Joystick LEFT to display previous one.
|
|
Pressing long (~1s) Joystick SEL, switches display mode to automatic one.
|
|
|
|
- Automatic Mode selected:
|
|
Images available on SD Card are displayed sequentially in a forever loop.
|
|
|
|
|
|
It is worth noting that the application manages some errors occurred during the
|
|
access to uSD card to parse bmp images:
|
|
|
|
- If SD Card is not FAT formatted, a message will be displayed on TFT.
|
|
In this case, format the SD card and put into its root directory the .bmp
|
|
files available within the FW package under Utilities\Media\Images folder.
|
|
|
|
- If the content of the SD card is other than a bitmap file, a message will
|
|
be displayed on TFT mentioning that it is not supported.
|
|
In this case, put into the SD card's root directory the .bmp
|
|
files available within the FW package under Utilities\Media\Images folder which are respecting
|
|
the following criteria:
|
|
o Dimensions: 128x160
|
|
o Width: 128 pixels
|
|
o Height: 160 pixels
|
|
o Bit depth: 16
|
|
o Item type: BMP file
|
|
o The name of the bmp image file must not exceed 11 characters (including
|
|
.bmp extension).
|
|
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate
|
|
delay (in milliseconds) based on variable incremented in SysTick ISR.
|
|
This implies that if HAL_Delay() is called from a peripheral ISR process,
|
|
then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to
|
|
1 millisecond to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- Demonstrations/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- Demonstrations/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- Demonstrations/Inc/main.h Header for main.c module
|
|
- Demonstrations/Inc/fatfs_storage.h Header for fatfs_storage.c module
|
|
- Demonstrations/Inc/ffconf.h FAT file system module configuration file
|
|
- Demonstrations/Src/stm32f0xx_it.c Interrupt handlers
|
|
- Demonstrations/Src/main.c Main program
|
|
- Demonstrations/Src/fatfs_storage.c Storage (FatFs) driver
|
|
- Demonstrations/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F091xC devices.
|
|
|
|
- This example has been tested with STM32F091RC-Nucleo RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- A SDSC microSD card (capacity up to 4GB), must contain the .bmp files at root
|
|
available under the FW package Utilities\Media\Images folder.
|
|
|
|
- Adafruit 1.8" TFT shield must be connected on CN5,CN6, CN8 and CN9 Arduino connectors,
|
|
for more details please refer to UM1726.
|
|
|
|
For more details about the adafruit 1.8" TFT shield, please visit:
|
|
http://www.adafruit.com/blog/2012/04/26/new-product-adafruit-1-8-18-bit-color-tft-shield-wmicrosd-and-joystick/
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|