/**
@page PWR_Standby PWR_STANDBY_RTC example
@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file PWR/PWR_STANDBY_RTC/readme.txt
* @author MCD Application Team
* @brief Description of the PWR STANDBY RTC example.
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to enter the Standby mode and wake up from this mode by using an external
reset or the RTC wakeup timer through the STM32F0xx RTC and RCC HAL,
and LL API (LL API use for maximizing performance).
It allows to measure the current consumption in STANDBY mode with RTC enabled.
In the associated software, the system clock is set to 48 MHz and the SysTick is
programmed to generate an interrupt each 1 ms.
The Low Speed Internal (LSI) clock is used as RTC clock source by default.
EXTI_Line20 is internally connected to the RTC Wakeup event.
The system automatically enters STANDBY mode 5 sec. after start-up. The RTC wake-up
is configured to generate an interrupt on rising edge about 26 sec. afterwards.
Current consumption in STANDBY mode with RTC feature enabled can be measured during that time.
More than half a minute is chosen to ensure current convergence to its lowest operating point.
Note: Due to LSI frequency variations, wake-up time is not guarantee. Adjustments need to be
done after getting the real measurement of LSI oscillator (or if available, LSE oscillator can
be used as well)
After wake-up from STANDBY mode, program execution restarts in the same way as after
a RESET.
LED2 is used to monitor the system state as follows:
- LED2 toggling: system in RUN mode
- LED2 off : system in STANDBY mode
These steps are repeated in an infinite loop.
@note To measure the current consumption in STANDBY mode, remove JP6 jumper
and connect an amperemeter to JP6 to measure IDD current.
@note This example can not be used in DEBUG mode due to the fact
that the Cortex-M0 core is no longer clocked during low power mode
so debugging features are disabled.
@note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select
the RTC clock source; in this case the Backup domain will be reset in
order to modify the RTC Clock source, as consequence RTC registers (including
the backup registers) and RCC_CSR register are set to their reset values.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application needs to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- PWR/PWR_STANDBY_RTC/Inc/stm32f0xx_conf.h HAL Configuration file
- PWR/PWR_STANDBY_RTC/Inc/stm32f0xx_it.h Header for stm32f0xx_it.c
- PWR/PWR_STANDBY_RTC/Inc/main.h Header file for main.c
- PWR/PWR_STANDBY_RTC/Src/system_stm32f0xx.c STM32F0xx system clock configuration file
- PWR/PWR_STANDBY_RTC/Src/stm32f0xx_it.c Interrupt handlers
- PWR/PWR_STANDBY_RTC/Src/main.c Main program
- PWR/PWR_STANDBY_RTC/Src/stm32f0xx_hal_msp.c HAL MSP module
@par Hardware and Software environment
- This example runs on STM32F0xx devices
- This example has been tested with STMicroelectronics STM32F072RB-Nucleo RevC
board and can be easily tailored to any other supported device
and development board.
- STM32F072RB-Nucleo RevC Set-up :
- LED2 connected to PA.05 pin
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Once the image is loaded, power off the NUCLEO board in unplugging
the power cable then power on the board again
- Run the example
*/
a58188598c