/**
@page I2C_WakeUpFromStop I2C Two Boards Communication IT Example on Stop Mode
@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file I2C/I2C_WakeUpFromStop/readme.txt
* @author MCD Application Team
* @brief Description of the Wake Up from Stop mode example
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to handle I2C data buffer transmission/reception between two boards,
using an interrupt when the device is in Stop mode.
_________________________ _________________________
| ______________| |______________ |
| | I2C1 | | I2C1| |
| | | | | |
| | SCL(PB6)|______________________|(PB6)SCL | |
| | | | | |
| | | | | |
| | | | | |
| | SDA(PB7)|______________________|(PB7)SDA | |
| | | | | |
| |______________| |______________| |
| __ | | __ |
| |__| | | |__| |
| USER GND|______________________|GND USER |
| | | |
|_STM32091C_EVAL__________| |_STM32091C_EVAL__________|
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 48 MHz. When The system is wakeup from stop mode,
system clock is 8 Mhz. The I2C peripheral is directly clocked by HSI.
The I2C peripheral configuration is ensured by the HAL_I2C_Init() function.
This later is calling the HAL_I2C_MspInit()function which core is implementing
the configuration of the needed I2C resources according to the used hardware (CLOCK,
GPIO and NVIC). You may update this function to change I2C configuration.
The I2C communication is then initiated.
The project is split in two parts the Master Board and the Slave Board
- Master Board
The HAL_I2C_Master_Receive_IT() and the HAL_I2C_Master_Transmit_IT() functions
allow respectively the reception and the transmission of a predefined data buffer
in Master mode using interrupt.
- Slave Board
The HAL_I2C_Slave_Receive_IT() and the HAL_I2C_Slave_Transmit_IT() functions
allow respectively the reception and the transmission of a predefined data buffer
in Slave mode using interrupt.
The user can choose between Master and Slave through "#define MASTER_BOARD"
in the "main.c" file:
- Uncomment "#define MASTER_BOARD" to select Master board.
- Comment "#define MASTER_BOARD" to select Slave board.
For this example the aTxBuffer is predefined and the aRxBuffer size is same as aTxBuffer.
In a first step after the user presses the Tamper push-button on the Master Board, I2C Master
starts the communication by sending aTxBuffer through HAL_I2C_Master_Transmit_IT() to
I2C Slave which wakes up from stop mode and receives aRxBuffer through HAL_I2C_Slave_Receive_IT().
The second step starts when the user presses the Tamper push-button on the Master Board,
the I2C Slave after wake up from stop mode at address match, sends aTxBuffer through HAL_I2C_Slave_Transmit_IT()
to the I2C Master which receives aRxBuffer through HAL_I2C_Master_Receive_IT().
The end of this two steps are monitored through the HAL_I2C_GetState() function
result.
Finally, aTxBuffer and aRxBuffer are compared through Buffercmp() in order to
check buffers correctness.
STM32091C-EVAL's LEDs can be used to monitor the transfer status on the Slave Board :
- LED1 is ON when the Transmission process is complete.
- LED1 is OFF when the Reception process is complete.
- LED3 is ON when there is an error in transmission/reception process.
- LED4 is ON when Slave enters stop mode.
- LED4 is OFF when Slave wakes up from stop.
@note I2Cx instance used and associated resources can be updated in "main.h"
file depending hardware configuration used.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- I2C/I2C_WakeUpFromStop/Inc/stm32f0xx_hal_conf.h HAL configuration file
- I2C/I2C_WakeUpFromStop/Inc/stm32f0xx_it.h I2C interrupt handlers header file
- I2C/I2C_WakeUpFromStop/Inc/main.h Header for main.c module
- I2C/I2C_WakeUpFromStop/Src/stm32f0xx_it.c I2C interrupt handlers
- I2C/I2C_WakeUpFromStop/Src/main.c Main program
- I2C/I2C_WakeUpFromStop/Src/system_stm32f0xx.c STM32F0xx system source file
- I2C/I2C_WakeUpFromStop/Src/stm32f0xx_hal_msp.c HAL MSP file
@par Hardware and Software environment
- This example runs on STM32F0xx devices.
- This example has been tested with STM32091C-EVAL board and can be
easily tailored to any other supported device and development board.
-STM32091C-EVAL Set-up
- Connect Master board PB6 to Slave Board PB6
- Connect Master board PB7 to Slave Board PB7
- Connect Master board GND to Slave Board GND
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
o Uncomment "#define MASTER_BOARD" and load the project in Master Board
o Comment "#define MASTER_BOARD" and load the project in Slave Board
- Run the example
*/
a58188598c