136 lines
6.6 KiB
Plaintext
136 lines
6.6 KiB
Plaintext
/**
|
|
@page I2C_TwoBoards_ComIT I2C Two Boards Communication IT Example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file I2C/I2C_TwoBoards_ComIT/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the I2C Two Boards Communication IT example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to handle I2C data buffer transmission/reception between two boards,
|
|
using an interrupt.
|
|
|
|
Board: STM32F072RB-Nucleo RevC (embeds a STM32F072RBT6 device)
|
|
SCL Pin: PB6 (CN10, pin17)
|
|
SDA Pin: PB7 (CN7, pin21)
|
|
|
|
_________________________ _________________________
|
|
| ______________| |______________ |
|
|
| |I2C1 | | I2C1| |
|
|
| | | | | |
|
|
| | SCL |_____________________| SCL | |
|
|
| | | | | |
|
|
| | | | | |
|
|
| | | | | |
|
|
| | SDA |_____________________| SDA | |
|
|
| | | | | |
|
|
| |______________| |______________| |
|
|
| | | |
|
|
| GND|_____________________|GND |
|
|
|_STM32_Board 1___________| |_STM32_Board 2___________|
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 48 MHz.
|
|
|
|
The I2C peripheral configuration is ensured by the HAL_I2C_Init() function.
|
|
This later is calling the HAL_I2C_MspInit()function which core is implementing
|
|
the configuration of the needed I2C resources according to the used hardware (CLOCK,
|
|
GPIO and NVIC). You may update this function to change I2C configuration.
|
|
|
|
The I2C communication is then initiated.
|
|
The project is split in two parts: the Master Board and the Slave Board
|
|
- Master Board
|
|
The HAL_I2C_Master_Receive_IT() and the HAL_I2C_Master_Transmit_IT() functions
|
|
allow respectively the reception and the transmission of a predefined data buffer
|
|
in Master mode using interrupt.
|
|
- Slave Board
|
|
The HAL_I2C_Slave_Receive_IT() and the HAL_I2C_Slave_Transmit_IT() functions
|
|
allow respectively the reception and the transmission of a predefined data buffer
|
|
in Slave mode using interrupt.
|
|
The user can choose between Master and Slave through "#define MASTER_BOARD"
|
|
in the "main.c" file:
|
|
- Uncomment "#define MASTER_BOARD" to select Master board.
|
|
- Comment "#define MASTER_BOARD" to select Slave board.
|
|
|
|
For this example the aTxBuffer is predefined and the aRxBuffer size is same as aTxBuffer.
|
|
|
|
In a first step after the user press the User push-button on the Master Board,
|
|
I2C Master starts the communication by sending aTxBuffer through HAL_I2C_Master_Transmit_IT()
|
|
to I2C Slave which receives aRxBuffer through HAL_I2C_Slave_Receive_IT().
|
|
The second step starts when the user press the User push-button on the Master Board,
|
|
the I2C Slave sends aTxBuffer through HAL_I2C_Slave_Transmit_IT()
|
|
to the I2C Master which receives aRxBuffer through HAL_I2C_Master_Receive_IT().
|
|
The end of this two steps are monitored through the HAL_I2C_GetState() function
|
|
result.
|
|
Finally, aTxBuffer and aRxBuffer are compared through Buffercmp() in order to
|
|
check buffers correctness.
|
|
|
|
STM32F072RB-Nucleo RevC's LED can be used to monitor the transfer status:
|
|
- LED2 is ON when the transmission process is complete.
|
|
- LED2 is OFF when the reception process is complete.
|
|
- LED2 is slowly blinking (1 sec. period) in case of error in initialization or
|
|
transmission/reception process
|
|
|
|
@note I2Cx instance used and associated resources can be updated in "main.h"
|
|
file depending hardware configuration used.
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@par Directory contents
|
|
|
|
- I2C/I2C_TwoBoards_ComIT/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- I2C/I2C_TwoBoards_ComIT/Inc/stm32f0xx_it.h I2C interrupt handlers header file
|
|
- I2C/I2C_TwoBoards_ComIT/Inc/main.h Header for main.c module
|
|
- I2C/I2C_TwoBoards_ComIT/Src/stm32f0xx_it.c I2C interrupt handlers
|
|
- I2C/I2C_TwoBoards_ComIT/Src/main.c Main program
|
|
- I2C/I2C_TwoBoards_ComIT/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
- I2C/I2C_TwoBoards_ComIT/Src/stm32f0xx_hal_msp.c HAL MSP file
|
|
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F072RB devices.
|
|
|
|
- This example has been tested with STM32F072RB-Nucleo RevC board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM32F072RB-Nucleo RevC Set-up
|
|
- Connect I2C_SCL line of Master board (PB6, CN10, pin17) to I2C_SCL line of Slave Board (PB6, CN10, pin17).
|
|
- Connect I2C_SDA line of Master board (PB7, CN7, pin21) to I2C_SDA line of Slave Board (PB7, CN7, pin21).
|
|
- Connect GND of Master board to GND of Slave Board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
o Uncomment "#define MASTER_BOARD" and load the project in Master Board
|
|
o Comment "#define MASTER_BOARD" and load the project in Slave Board
|
|
- Run the example
|
|
|
|
|
|
*/
|