/**
@page IWDG_Reset Independent Watchdog Reset Example
@verbatim
********************* COPYRIGHT(c) 2016 STMicroelectronics *******************
* @file IWDG/IWDG_Reset/readme.txt
* @author MCD Application Team
* @brief Description of the IWDG Reset.
******************************************************************************
* @attention
*
* Copyright (c) 2016 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
@endverbatim
@par Example Description
How to handle the IWDG reload counter and simulate a software fault that generates
an MCU IWDG reset after a preset laps of time.
At the beginning of the main program the HAL_Init() function is called to reset
all the peripherals, initialize the Flash interface and the systick.
Then the SystemClock_Config() function is used to configure the system
clock (SYSCLK) to run at 48 MHz.
The IWDG timeout is set to 1 second.
First, the TIM14 timer is configured to measure the LSI frequency as the
LSI is internally connected to TIM14 CH1, in order to adjust the IWDG clock.
The LSI frequency value could be monitored on debugger in "uwLsiFreq" variable.
The LSI measurement using the TIM14 is described below:
- Configure the TIM14 to remap internally the TIM14 CH1 Input Capture to the LSI
clock output.
- Enable the TIM14 Input Capture interrupt: after one cycle of LSI clock, the
period value is stored in a variable and compared to the HCLK clock to get
its real value.
Then, the IWDG reload counter is configured as below to obtain 1 second according
to the measured LSI frequency after setting the prescaler value:
IWDG counter clock Frequency = LSI Frequency / Prescaler value
The IWDG reload counter is refreshed each 990 ms in the main program infinite
loop to prevent a IWDG reset.
LED3 is also toggling each 990 ms indicating that the program is running.
An EXTI Line is connected to a GPIO pin, configured to generate an interrupt
when putting or removing a jumper between PA.12 (Arduino D2) and GND.
The EXTI Line is used to simulate a software failure: once the EXTI Line event
occurs, by putting or removing a jumper between PA.12 (Arduino D2) and GND,
the corresponding interrupt is served.
In the ISR, a write to invalid address generates a Hardfault exception
containing an infinite loop and preventing to return to main program (the IWDG
reload counter is not refreshed).
As a result, when the IWDG counter reaches 0, the IWDG reset occurs.
If the IWDG reset is generated, after the system resumes from reset, LED3 turns on for 4 seconds.
If the EXTI Line event does not occur, the IWDG counter is indefinitely refreshed in the main
program infinite loop, and there is no IWDG reset.
If the user button is pressed while LED3 is turned on, another Hardfault exception is triggered.
In this case, since the IWDG has not been reprogrammed yet, the software ends up
stuck in the hardfault. All LEDs are turned off in this situation.
LED3 will turn off if any error occurs.
@note Care must be taken when using HAL_Delay(), this function provides accurate
delay (in milliseconds) based on variable incremented in SysTick ISR. This
implies that if HAL_Delay() is called from a peripheral ISR process, then
the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- IWDG/IWDG_Reset/Inc/stm32f0xx_hal_conf.h HAL configuration file
- IWDG/IWDG_Reset/Inc/stm32f0xx_it.h Interrupt handlers header file
- IWDG/IWDG_Reset/Inc/main.h Header for main.c module
- IWDG/IWDG_Reset/Src/stm32f0xx_it.c Interrupt handlers
- IWDG/IWDG_Reset/Src/main.c Main program
- IWDG/IWDG_Reset/Src/stm32f0xx_hal_msp.c HAL MSP file
- IWDG/IWDG_Reset/Src/system_stm32f0xx.c STM32F0xx system source file
@par Hardware and Software environment
- This example runs on STM32F0xx devices.
- This example has been tested with STM32F042K6-Nucleo(revC) board and can be
easily tailored to any other supported device and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
*/
a58188598c