93 lines
3.4 KiB
Plaintext
93 lines
3.4 KiB
Plaintext
/**
|
|
@page BSP Example on how to use the BSP drivers
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file BSP/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the BSP example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example provides a description of how to use the different BSP drivers.
|
|
|
|
At the beginning of the main program the HAL_Init() function is called to reset
|
|
all the peripherals, initialize the Flash interface and the systick.
|
|
Then the SystemClock_Config() function is used to configure the system
|
|
clock (SYSCLK) to run at 48 MHz.
|
|
|
|
This example shows how to use the different functionalities of components
|
|
available on the board by switching between all tests using Tamper push-button button.
|
|
|
|
** Push the User button to start first Test.
|
|
Blue Led (LD4) will blink between each test. Press Tamper push-button to start another test:
|
|
|
|
** JOYSTICK **
|
|
Use the joystick button to move a pointer inside a rectangle
|
|
(up/down/right/left) and change the pointer color(select).
|
|
|
|
** LCD **
|
|
This example shows how to use the different LCD features to display string
|
|
with different fonts, to display different shapes and to draw a bitmap.
|
|
|
|
** SD **
|
|
This example shows how to erase, write and read the SD card and also
|
|
how to detect the presence of the card.
|
|
|
|
** EEPROM **
|
|
This example show how to read and write data in EEPROM I2C M24LR64 connected on STM32091C-EVAL
|
|
* The I2C RF EEPROM memory (M24LR64) is available through the connector CN2
|
|
|
|
** TSENSOR **
|
|
This example show how to read a Temperature using the temperature sensor.
|
|
|
|
** LCD LOG **
|
|
This example show how to use the LCD log features.
|
|
|
|
@par Directory contents
|
|
|
|
- BSP/Src/main.c Main program
|
|
- BSP/Src/system_stm32f0xx.c STM32F0xx system clock configuration file
|
|
- BSP/Src/stm32f0xx_it.c Interrupt handlers
|
|
- BSP/Src/joystick.c joystick feature
|
|
- BSP/Src/lcd.c LCD drawing features
|
|
- BSP/Src/log.c LCD Log firmware functions
|
|
- BSP/Src/sd.c SD features
|
|
- BSP/Src/eeprom.c EEPROM Read/Write features
|
|
- BSP/Src/temperature_sensor.c Temperature Sensor features
|
|
- BSP/Inc/main.h Main program header file
|
|
- BSP/Inc/stm32f0xx_conf.h HAL Configuration file
|
|
- BSP/Inc/stm32f0xx_it.h Interrupt handlers header file
|
|
- BSP/Inc/lcd_log_conf.h lcd_log configuration template file
|
|
- BSP/Inc/stlogo.h Image used for BSP example
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F0xx devices.
|
|
|
|
- This example has been tested with STMicroelectronics STM32091C-EVAL
|
|
evaluation boards and can be easily tailored to any other supported device
|
|
and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|