74 lines
2.9 KiB
Plaintext
74 lines
2.9 KiB
Plaintext
/**
|
|
@page ADC_TriggerMode ADC1 conversion using Trigger Mode
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file ADC/ADC_TriggerMode/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the ADC Trigger Mode example.
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* Copyright (c) 2016 STMicroelectronics.
|
|
* All rights reserved.
|
|
*
|
|
* This software is licensed under terms that can be found in the LICENSE file
|
|
* in the root directory of this software component.
|
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
How to use ADC1 and TIM2 to continuously convert data from an ADC channel.
|
|
Each time an external trigger is generated by TIM2 a new conversion is started
|
|
by the ADC.
|
|
|
|
Each time an external trigger is generated by TIM2 a new conversion is started by ADC1.
|
|
|
|
At the end of conversion, an interrupt is generated and the converted data of
|
|
ADC1 DR register is affected to the uhADCxConvertedValue variable in the ADC
|
|
conversion complete call back function (HAL_ADC_ConvCpltCallback).
|
|
The converted values can be monitored by adding "uhADCxConvertedValue" to the debugger.
|
|
|
|
The timer is used to trigger an ADC measure at 20 KHz.
|
|
|
|
Configuration of the timer to trig an ADC measure at 20 Khz:
|
|
From the reference manual, Reset and Clock control part, Timer 2 is clocked on PCLK1.
|
|
The function SystemClock_Config() configures the clock divider as follows:
|
|
1) The system clock is 48 MHz.
|
|
2) AHB Prescaler = 1 => AHB clock is 48 MHz.
|
|
So, in TIM_Config function, we set the following period: htim.Init.Period = 2400;
|
|
|
|
The voltage on pin PC.00 (ADC_CHANNEL_10)can vary using the board potentiometer RV3.
|
|
|
|
Remark: LED3 is ON when there is an error in initialization.
|
|
|
|
@par Directory contents
|
|
|
|
- ADC/ADC_TriggerMode/Inc/stm32f0xx_hal_conf.h HAL configuration file
|
|
- ADC/ADC_TriggerMode/Inc/stm32f0xx_it.h DMA interrupt handlers header file
|
|
- ADC/ADC_TriggerMode/Inc/main.h Header for main.c module
|
|
- ADC/ADC_TriggerMode/Src/stm32f0xx_it.c DMA interrupt handlers
|
|
- ADC/ADC_TriggerMode/Src/main.c Main program
|
|
- ADC/ADC_TriggerMode/Src/stm32f0xx_hal_msp.c HAL MSP file
|
|
- ADC/ADC_TriggerMode/Src/system_stm32f0xx.c STM32F0xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F0xx devices.
|
|
|
|
- This example has been tested with STM32091C-EVAL board and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
*/
|