103 lines
2.7 KiB
Go
103 lines
2.7 KiB
Go
//go:build example
|
|
// +build example
|
|
|
|
//
|
|
// Do not build by default.
|
|
|
|
package main
|
|
|
|
import (
|
|
"fmt"
|
|
"time"
|
|
|
|
"gobot.io/x/gobot/v2"
|
|
"gobot.io/x/gobot/v2/platforms/nanopi"
|
|
"gobot.io/x/gobot/v2/system"
|
|
)
|
|
|
|
const (
|
|
inPinNum = "22" // 7, 8, 10, 11, 12, 13, 15, 16, 18, 22
|
|
outPinNum = "23"
|
|
outPinInvertedNum = "24"
|
|
debounceTime = 2 * time.Second
|
|
)
|
|
|
|
var (
|
|
outPin gobot.DigitalPinner
|
|
outPinInverted gobot.DigitalPinner
|
|
)
|
|
|
|
// Wiring
|
|
// PWR NanoPi: 1, 17 (+3.3V, VCC); 2, 4 (+5V, VDD); 6, 9, 14, 20 (GND)
|
|
// GPIO NanoPi: header pin 22 is input, pin 23 is normal output, pin 24 is inverted output
|
|
// Button: the input pin is wired with a button to GND, the internal pull up resistor is used
|
|
// LED's: the output pins are wired to the cathode of a LED, the anode is wired with a resistor (70-130Ohm for 20mA) to VCC
|
|
// Expected behavior: always one LED is on, the other in opposite state, if button is pressed for >2 seconds the state changes
|
|
func main() {
|
|
board := nanopi.NewNeoAdaptor()
|
|
|
|
work := func() {
|
|
inPin, err := board.DigitalPin(inPinNum)
|
|
if err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
if err := inPin.ApplyOptions(system.WithPinDirectionInput(), system.WithPinPullUp(),
|
|
system.WithPinDebounce(debounceTime), system.WithPinEventOnBothEdges(buttonEventHandler)); err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
|
|
// note: WithPinOpenDrain() is optional, if using WithPinOpenSource() the LED's will not light up
|
|
outPin, err = board.DigitalPin(outPinNum)
|
|
if err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
if err := outPin.ApplyOptions(system.WithPinDirectionOutput(1), system.WithPinOpenDrain()); err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
|
|
outPinInverted, err = board.DigitalPin(outPinInvertedNum)
|
|
if err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
if err := outPinInverted.ApplyOptions(system.WithPinActiveLow(), system.WithPinDirectionOutput(1),
|
|
system.WithPinOpenDrain()); err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
|
|
fmt.Printf("\nPlease press and hold the button for at least %s\n", debounceTime)
|
|
}
|
|
|
|
robot := gobot.NewRobot("pinEdgeBot",
|
|
[]gobot.Connection{board},
|
|
[]gobot.Device{},
|
|
work,
|
|
)
|
|
|
|
robot.Start()
|
|
}
|
|
|
|
func buttonEventHandler(offset int, t time.Duration, et string, sn uint32, lsn uint32) {
|
|
fmt.Printf("%s: %s detected on line %d with total sequence %d and line sequence %d\n", t, et, offset, sn, lsn)
|
|
level := 1
|
|
|
|
if et == "falling edge" {
|
|
level = 0
|
|
}
|
|
|
|
if outPin != nil {
|
|
err := outPin.Write(level)
|
|
fmt.Printf("pin %s is now %d\n", outPinNum, level)
|
|
if err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
}
|
|
|
|
if outPinInverted != nil {
|
|
err := outPinInverted.Write(level)
|
|
fmt.Printf("pin %s is now not %d\n", outPinInvertedNum, level)
|
|
if err != nil {
|
|
fmt.Println(err)
|
|
}
|
|
}
|
|
}
|