121 lines
5.4 KiB
C
121 lines
5.4 KiB
C
/****************************************************************************
|
|
* boards/renesas/m16c/skp16c26/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_RENESAS_M16C_SKP16C26_INCLUDE_BOARD_H
|
|
#define __BOARDS_RENESAS_M16C_SKP16C26_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* User configuration checks ************************************************/
|
|
|
|
/* According to SKP16C26 documentation, "SIO/UART1 pins are used for
|
|
* communication between the SKP16C26 board kernel and KD30 Debugger through
|
|
* the ICD. Do not connect these pins to any other circuit, as UART1 cannot
|
|
* be used in the user program.
|
|
* For details, please see ICD (RTA-FoUSB-MON) User Manual on Target M16C
|
|
* ROM Monitor Resources or related ICD application notes."
|
|
*
|
|
* However, the schematic appears to show that SIO/UART2 is actual
|
|
* connection.
|
|
* To be safe, we will error out on either selection:
|
|
*/
|
|
|
|
#if defined(CONFIG_M16C_UART1) || defined(CONFIG_M16C_UART2)
|
|
# error "UART1/2 should not be used on SKP16C26"
|
|
#endif
|
|
|
|
/* Hardware defintitions ****************************************************/
|
|
|
|
/* Xin Freq */
|
|
|
|
#define M16C_XIN_FREQ 20000000 /* 20MHz */
|
|
|
|
/* Interrupt Priority Levels ************************************************/
|
|
|
|
/* IPL settings */
|
|
|
|
#define M16C_DEFAULT_IPL 0 /* Default M16C Interrupt priority level */
|
|
#undef M16C_INTERRUPT_IPL /* Default interrupt IPL to enabled nested interrupts */
|
|
|
|
/* Define any of the following to specify interrupt priorities. A default
|
|
* value of 5 will be used for any unspecified values
|
|
*/
|
|
|
|
#undef M16C_INT3_PRIO /* INT3 interrupt priority */
|
|
#undef M16C_INT5_PRIO /* INT5 interrupt priority */
|
|
#undef M16C_INT4_PRIO /* INT4 interrupt priority */
|
|
#undef M16C_BCN_PRIO /* Bus collision detection interrupt priority */
|
|
#undef M16C_DM0_PRIO /* DMA0 interrupt priority */
|
|
#undef M16C_DM1_PRIO /* DMA1 interrupt priority */
|
|
#undef M16C_KUP_PRIO /* Key input interrupt priority */
|
|
#undef M16C_AD_PRIO /* A-D conversion interrupt priority */
|
|
#undef M16C_S2T_PRIO /* UART2 transmit interrupt priority */
|
|
#undef M16C_S2R_PRIO /* UART2 receive interrupt priority */
|
|
#undef M16C_S0T_PRIO /* UART0 transmit interrupt priority */
|
|
#undef M16C_S0R_PRIO /* UART0 receive interrupt priority */
|
|
#undef M16C_S1T_PRIO /* UART1 transmit interrupt priority */
|
|
#undef M16C_S1R_PRIO /* UART1 receive interrupt priority */
|
|
#define M16C_TA0_PRIO 5 /* Timer A0 interrupt priority */
|
|
#undef M16C_TA1_PRIO /* Timer A1 interrupt priority */
|
|
#undef M16C_TA2_PRIO /* Timer A2 interrupt priority */
|
|
#undef M16C_TA3_PRIO /* Timer A3 interrupt priority */
|
|
#undef M16C_TA4_PRIO /* Timer A4 interrupt priority */
|
|
#undef M16C_TB0_PRIO /* Timer B0 interrupt priority */
|
|
#undef M16C_TB1_PRIO /* Timer B1 interrupt priority */
|
|
#undef M16C_TB2_PRIO /* Timer B2 interrupt priority */
|
|
#undef M16C_INT0_PRIO /* INT0 interrupt priority */
|
|
#undef M16C_INT1_PRIO /* INT1 interrupt priority */
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* GREEN YELLOW RED */
|
|
#define LED_STARTED 0 /* OFF OFF OFF */
|
|
#define LED_HEAPALLOCATE 1 /* ON OFF OFF */
|
|
#define LED_IRQSENABLED 2 /* OFF ON OFF */
|
|
#define LED_STACKCREATED 3 /* ON ON OFF */
|
|
#define LED_INIRQ 4 /* ON OFF ON */
|
|
#define LED_SIGNAL 5 /* OFF ON ON */
|
|
#define LED_ASSERTION 6 /* ON ON ON */
|
|
#define LED_PANIC 7 /* NC** NC** ON* */
|
|
|
|
/* *=FLASHING **=if INIRQ, SIGNAL, or ASSERTION will be flashing */
|
|
|
|
/* BUTTON definitions *******************************************************/
|
|
|
|
#define SW1_PRESSED 0x01 /* Bit 0: 1=SW1 pressed */
|
|
#define SW2_PRESSED 0x02 /* Bit 1: 1=SW2 pressed */
|
|
#define SW3_PRESSED 0x04 /* Bit 2: 1=SW3 pressed */
|
|
|
|
/****************************************************************************
|
|
* Inline Functions
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
#endif
|
|
|
|
#endif /* __BOARDS_RENESAS_M16C_SKP16C26_INCLUDE_BOARD_H */
|