191 lines
6.0 KiB
Plaintext
191 lines
6.0 KiB
Plaintext
README
|
|
======
|
|
|
|
This directory contains the port of NuttX to the Adafruit KB2040.
|
|
See https://www.adafruit.com/product/5302 for information about Adafruit KB2040.
|
|
|
|
NuttX supports the following RP2040 capabilities:
|
|
- UART (console port)
|
|
- GPIO 0 (UART0 TX) and GPIO 1 (UART0 RX) are used for the console.
|
|
- I2C
|
|
- SPI (master only)
|
|
- DMAC
|
|
- PWM
|
|
- ADC
|
|
- Watchdog
|
|
- USB device
|
|
- MSC, CDC/ACM serial and these composite device are supported.
|
|
- CDC/ACM serial device can be used for the console.
|
|
- PIO (RP2040 Programmable I/O)
|
|
- Flash ROM Boot
|
|
- SRAM Boot
|
|
- If Pico SDK is available, nuttx.uf2 file which can be used in
|
|
BOOTSEL mode will be created.
|
|
- Persistent flash filesystem in unused flash ROM
|
|
|
|
NuttX also provide support for these external devices:
|
|
|
|
- BMP180 sensor at I2C0 (don't forget to define I2C0 GPIOs at "I2C0 GPIO pin assign" in Board Selection menu)
|
|
- INA219 sensor / module (don't forget to define I2C0 GPIOs at "I2C0 GPIO pin assign" in Board Selection menu)
|
|
- Pico Display Pack (ST7789 LCD)
|
|
- RGB leds and buttons are not supported yet.
|
|
- Pico Audio Pack (PCM5100A I2S DAC)
|
|
- I2S interface is realized by PIO.
|
|
- WS2812 smart pixel support
|
|
|
|
There is currently no direct user mode access to these RP2040 hardware features:
|
|
- SPI Slave Mode
|
|
- SSI
|
|
- RTC
|
|
- Timers
|
|
|
|
Installation
|
|
============
|
|
|
|
1. Download Raspberry Pi Pico SDK
|
|
|
|
$ git clone -b 1.1.2 https://github.com/raspberrypi/pico-sdk.git
|
|
|
|
2. Set PICO_SDK_PATH environment variable
|
|
|
|
$ export PICO_SDK_PATH=<absolute_path_to_pico-sdk_directory>
|
|
|
|
3. Configure and build NuttX
|
|
|
|
$ git clone https://github.com/apache/nuttx.git nuttx
|
|
$ git clone https://github.com/apache/nuttx-apps.git apps
|
|
$ cd nuttx
|
|
$ make distclean
|
|
$ ./tools/configure.sh raspberrypi-pico:nsh
|
|
$ make V=1
|
|
|
|
4. Connect Adafruit KB2040 board to USB port while pressing BOOTSEL.
|
|
The board will be detected as USB Mass Storage Device.
|
|
Then copy "nuttx.uf2" into the device.
|
|
(Same manner as the standard Pico SDK applications installation.)
|
|
|
|
5. To access the console, GPIO 0 and 1 pins must be connected to the
|
|
device such as USB-serial converter.
|
|
|
|
`usbnsh` configuration provides the console access by USB CDC/ACM serial
|
|
devcice. The console is available by using a terminal software on the USB
|
|
host.
|
|
|
|
Defconfigs
|
|
==========
|
|
|
|
- nsh
|
|
Minimum configuration with NuttShell
|
|
|
|
- nsh-flash
|
|
NuttX shell with SMART flash filesystem.
|
|
|
|
- nshsram
|
|
Load NuttX binary to SRAM
|
|
|
|
- smp
|
|
Enable SMP mode. Both Core 0 and Core 1 are used by NuttX.
|
|
|
|
- ssd1306
|
|
SSD1306 OLED display (I2C) test configuration
|
|
Connection:
|
|
SSD1306 Raspberry Pi Pico
|
|
GND ----- GND (Pin 3 or 38 or ...)
|
|
VCC ----- 3V3 OUT (Pin 36)
|
|
SDA ----- GP4 (I2C0 SDA) (Pin 6)
|
|
SCL ----- GP5 (I2C0 SCL) (Pin 7)
|
|
|
|
- lcd1602
|
|
LCD 1602 Segment LCD Disaply (I2C)
|
|
Connection:
|
|
PCF8574 BackPack Raspberry Pi Pico
|
|
GND ----- GND (Pin 3 or 38 or ...)
|
|
VCC ----- 5V Vbus (Pin 40)
|
|
SDA ----- GP4 (I2C0 SDA) (Pin 6)
|
|
SCL ----- GP5 (I2C0 SCL) (Pin 7)
|
|
- spisd
|
|
SD card support (SPI connection)
|
|
Connection:
|
|
SD card slot Raspberry Pi Pico
|
|
DAT2 (NC)
|
|
DAT3/CS ----- GP17 (SPI0 CSn) (Pin 22)
|
|
CMD /DI ----- GP19 (SPI0 TX) (Pin 25)
|
|
VDD ----- 3V3 OUT (Pin 36)
|
|
CLK/SCK ----- GP18 (SPI0 SCK) (Pin 24)
|
|
VSS ----- GND (Pin 3 or 38 or ...)
|
|
DAT0/DO ----- GP16 (SPI0 RX) (Pin 21)
|
|
DAT1 (NC)
|
|
* Card hot swapping is not supported.
|
|
|
|
- st7735
|
|
st7735 SPI LCD support
|
|
Connection:
|
|
st7735 Raspberry Pi Pico
|
|
GND ----- GND (Pin 3 or 38 or ...)
|
|
VCC ----- 5V Vbus (Pin 40)
|
|
SDA ----- GP15 (SPI1 TX) (Pin 20)
|
|
SCK ----- GP14 (SPI1 SCK) (Pin 19)
|
|
CS ----- GP13 (SPI1 CSn) (Pin 17)
|
|
AO(D/C) ----- GP12 (SPI1 RX) (Pin 16)
|
|
BL ----- GP11 (Pin 15)
|
|
RESET ----- GP10 (Pin 14)
|
|
|
|
- enc28j60
|
|
ENC28J60 SPI ethernet controller support
|
|
- IP address is configured by DHCP.
|
|
- DNS address is 8.8.8.8 (CONFIG_NETINIT_DNSIPADDR)
|
|
- NTP client is enabled.
|
|
Connection:
|
|
ENC28J60 Raspberry Pi Pico
|
|
GND ----- GND (Pin 3 or 38 or ...)
|
|
3.3 ----- 3V3 OUT (Pin 36)
|
|
SI ----- GP15 (SPI1 TX) (Pin 20)
|
|
SCK ----- GP14 (SPI1 SCK) (Pin 19)
|
|
CS ----- GP13 (SPI1 CSn) (Pin 17)
|
|
SO ----- GP12 (SPI1 RX) (Pin 16)
|
|
INT ----- GP11 (Pin 15)
|
|
RESET ----- GP10 (Pin 14)
|
|
|
|
- displaypack
|
|
Pico Display Pack support
|
|
See the following page for connection:
|
|
https://shop.pimoroni.com/products/pico-display-pack
|
|
|
|
- audiopack
|
|
Pico Audio Pack support
|
|
See the following page for connection:
|
|
https://shop.pimoroni.com/products/pico-audio-pack
|
|
SD card interface is also enabled.
|
|
|
|
- usbnsh
|
|
USB CDC/ACM serial console with NuttShell
|
|
|
|
- usbmsc
|
|
USB MSC and CDC/ACM support
|
|
`msconn` and `sercon` commands enable the MSC and CDC/ACM devices.
|
|
The MSC support provides the interface to the SD card with SPI,
|
|
so the SD card slot connection like spisd configuration is required.
|
|
|
|
- composite
|
|
USB composite device (MSC + CDC/ACM) support
|
|
`conn` command enables the composite device.
|
|
|
|
License exceptions
|
|
==================
|
|
|
|
The following files are originated from the files in Pico SDK.
|
|
So, the files are licensed under 3-Clause BSD same as Pico SDK.
|
|
|
|
- arch/arm/src/rp2040/rp2040_clock.c
|
|
- arch/arm/src/rp2040/rp2040_pll.c
|
|
- arch/arm/src/rp2040/rp2040_xosc.c
|
|
- These are created by referring the Pico SDK clock initialization.
|
|
|
|
- arch/arm/src/rp2040/rp2040_pio.c
|
|
- arch/arm/src/rp2040/rp2040_pio.h
|
|
- arch/arm/src/rp2040/rp2040_pio_instructions.h
|
|
- These provide the similar APIs to Pico SDK's hardware_pio APIs.
|
|
|
|
- arch/arm/src/rp2040/hardware/*.h
|
|
- These are generated from rp2040.svd originally provided in Pico SDK.
|