220 lines
7.6 KiB
Plaintext
220 lines
7.6 KiB
Plaintext
README
|
|
======
|
|
|
|
This README file discusses the port of NuttX to the Silicon Labs EFM32™
|
|
Giant Gecko Starter Kit (EFM32GG-STK3400). The Giant Gecko Starter Kit
|
|
features:
|
|
|
|
• EFM32GG990F1024 MCU with 1 MB flash and 128 kB RAM
|
|
• 32.768 kHz crystal (LXFO)
|
|
• 48 MHz crystal (HXFO)
|
|
• 32 MB NAND flash
|
|
• Advanced Energy Monitoring
|
|
• Touch slider
|
|
• 8x20 LCD
|
|
• 2 user LEDs
|
|
• 2 user buttons
|
|
• USB interface for Host/Device/OTG
|
|
• Ambient light sensor and inductive-capacitive metal sensor
|
|
• EFM32 OPAMP footprint
|
|
• 20 pin expansion header
|
|
• Breakout pads for easy access to I/O pins
|
|
• Power sources (USB and CR2032 battery)
|
|
• Backup Capacitor for RTC mode
|
|
• Integrated Segger J-Link USB debugger/emulator
|
|
|
|
STATUS
|
|
======
|
|
|
|
2014-11-02: Completed the basic NSH configuration for the EFM32 Giant Gecko
|
|
Starter Kit.
|
|
2014-11-12: The basic NSH configuration is functional with a serial console
|
|
on LEUART0.
|
|
2014-11-14: LEUART0 BAUD increased from 2400 to 9600. Calibrated delay
|
|
loop.
|
|
2014-11-18: Added basic drivers for USB device and host. The initial port
|
|
is a simple leverage from the STM32 which appears to use the same IP.
|
|
The current state is just the STM32 USB drivers with the appropriate.
|
|
The USB drivers still lack EFM32 initialization logic and are, of course,
|
|
completely untested.
|
|
|
|
LEDs and Buttons
|
|
================
|
|
|
|
LEDs
|
|
----
|
|
The EFM32 Giant Gecko Start Kit has two yellow LEDs marked LED0 and LED1.
|
|
These LEDs are controlled by GPIO pins on the EFM32. The LEDs are
|
|
connected to pins PE2 and PE3 in an active high configuration:
|
|
|
|
------------------------------------- --------------------
|
|
EFM32 PIN BOARD SIGNALS
|
|
------------------------------------- --------------------
|
|
E2/BCK_VOUT/EBI_A09 #0/ MCU_PE2 UIF_LED0
|
|
TIM3_CC2 #1/U1_TX #3/ACMP0_O #1
|
|
E3/BCK_STAT/EBI_A10 #0/U1_RX #3/ MCU_PE3 UIF_LED1
|
|
ACMP1_O #1
|
|
------------------------------------- --------------------
|
|
|
|
All LEDs are grounded and so are illuminated by outputting a high
|
|
value to the LED.
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/efm32_autoleds.c. The LEDs are used to
|
|
encode OS-related events as follows:
|
|
|
|
These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
|
|
defined. In that case, the usage by the board port is defined in
|
|
include/board.h and src/up_leds.c. The LEDs are used to encode
|
|
OS-related events as follows:
|
|
|
|
SYMBOL Meaning LED state
|
|
LED0 LED1
|
|
------------------- ----------------------- -------- --------
|
|
LED_STARTED NuttX has been started OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF
|
|
LED_STACKCREATED Idle stack created ON OFF
|
|
LED_INIRQ In an interrupt No change
|
|
LED_SIGNAL In a signal handler No change
|
|
LED_ASSERTION An assertion failed No change
|
|
LED_PANIC The system has crashed OFF Blinking
|
|
LED_IDLE STM32 is is sleep mode Not used
|
|
|
|
Thus if LED0 statically on, NuttX has successfully booted and is,
|
|
apparently, running normally. If LED1 is flashing at approximately
|
|
2Hz, then a fatal error has been detected and the system has halted.
|
|
|
|
Buttons
|
|
-------
|
|
The EFM32 Giant Gecko Start Kit has two buttons marked PB0 and PB1. They
|
|
are connected to the EFM32, and are debounced by RC filters with a time
|
|
constant of 1ms. The buttons are connected to pins PB9 and PB10:
|
|
|
|
------------------------------------- --------------------
|
|
EFM32 PIN BOARD SIGNALS
|
|
------------------------------------- --------------------
|
|
B9/EBI_A03/U1_TX #2 MCU_PB9 UIF_PB0
|
|
B10/EBI_A04/U1_RX #2 MCU_PB10 UIF_PB1
|
|
------------------------------------- --------------------
|
|
|
|
Buttons are connected to ground so they will read low when closed.
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
Default Serial Console
|
|
----------------------
|
|
LEUART0 is configured as the default serial console at 9600 8N1
|
|
on pins PD5 and PD4.
|
|
|
|
---------- ---- ----------- -----------
|
|
SIGNAL PGIO EXP Header Test Point
|
|
---------- ---- ----------- -----------
|
|
LEUART0_TX PD4 Pin 12 TPJ122
|
|
LEUART0_RX PD5 Pin 14 TPJ123
|
|
---------- ---- ----------- -----------
|
|
|
|
It should also be possible to use UART0 is configured at 115200 8N1
|
|
on pins PE0 and PE1.
|
|
|
|
Communication through the Board Controller
|
|
------------------------------------------
|
|
The kit contains a board controller that is responsible for performing
|
|
various board level tasks, such as handling the debugger and the Advanced
|
|
Energy Monitor. An interface is provided between the EFM32 and the board
|
|
controller in the form of a UART connection. The connection is enabled by
|
|
setting the EFM_BC_EN (PF7) line high, and using the lines EFM_BC_TX
|
|
(PE0) and EFM_BC_RX (PE1) for communicating.
|
|
|
|
USING THE J-LINK GDB SERVER
|
|
===========================
|
|
|
|
1. Star the J-Link GDB server. You should see the start-up configuration
|
|
window. SelectL
|
|
|
|
a. Target device = EFM32GG990F1024
|
|
b. Select Target interface = SWD
|
|
|
|
2. Press OK. The GDB server should start and the last message in the Log
|
|
output should be "Waiting for GDB connection".
|
|
|
|
3. In a terminal window, start GDB:
|
|
|
|
arm-none-eabi-gdb
|
|
|
|
4. Connect to the J-Link GDB server:
|
|
|
|
(gdb) target remote localhost:2331
|
|
|
|
5. Load and run nuttx
|
|
|
|
(gdb) mon halt
|
|
(gdb) load nuttx
|
|
(gdb) mon reset go
|
|
|
|
I had to tinker with the setup a few times repeating the same steps above
|
|
before things finally began to work. Don't know why.
|
|
|
|
To debug code already burned into FLASH:
|
|
|
|
1. Start the GDB server as above.
|
|
|
|
2. In a terminal window, start GDB:
|
|
|
|
arm-none-eabi-gdb
|
|
|
|
3. Connect to the J-Link GDB serer:
|
|
|
|
(gdb) target remote local host
|
|
|
|
3. Load the nuttx symbol file, reset, and debug
|
|
|
|
(gdb) mon halt
|
|
(gdb) file nuttx
|
|
(gdb) mon reset
|
|
(gdb) s
|
|
...
|
|
|
|
Configurations
|
|
==============
|
|
Each EFM32 Giant Gecko Starter Kit configuration is maintained in a sub-
|
|
directory and can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh efm32gg-stk3700/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
If this is a Windows native build, then configure.bat should be used
|
|
instead of configure.sh:
|
|
|
|
configure.bat efm32gg-stk3700\<subdir>
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
nsh:
|
|
---
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. The
|
|
Configuration enables the serial interfaces on LEUART0 at 9600 8N1.
|
|
|
|
NOTES:
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To
|
|
change this configuration using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
and misc/tools/
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. By default, this configuration uses the CodeSourcery toolchain
|
|
for Windows and builds under Cygwin (or probably MSYS). That
|
|
can easily be reconfigured, of course.
|
|
|
|
CONFIG_HOST_WINDOWS=y : Builds under Windows
|
|
CONFIG_WINDOWS_CYGWIN=y : Using Cygwin
|
|
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery for Windows
|