386 lines
14 KiB
Plaintext
386 lines
14 KiB
Plaintext
README
|
||
^^^^^^
|
||
|
||
README for NuttX port to the Stellaris RDK-S2E Reference Design Kit and
|
||
the MDL-S2E Ethernet to Serial module.
|
||
|
||
Contents
|
||
^^^^^^^^
|
||
|
||
Stellaris RDK-S2E Reference Design Kit
|
||
Development Environment
|
||
GNU Toolchain Options
|
||
IDEs
|
||
NuttX buildroot Toolchain
|
||
Stellaris MDL-S2E Reference Design Configuration Options
|
||
Configurations
|
||
|
||
Stellaris RDK-S2E Reference Design Kit
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
The Stellaris RDK-S2E Reference Design Kit includes the following features:
|
||
|
||
o MDL-S2E Ethernet to serial module
|
||
o LM3S6432 in a 10 x 10 mm BGA package for reduced board size
|
||
o 10/100 Mbit Ethernet port
|
||
o Auto MDI/MDIX cross-over correction
|
||
o Traffic and link indicators Serial ports
|
||
o UART ports include RTS/CTS for flow control
|
||
o UART0 has RS232 levels, transceiver runs at up to 230.4 Kbaud
|
||
o UART1 has CMOS/TTL levels, can run at 1.0 Mbaud
|
||
|
||
Features of the LM3S6432 Microcontroller
|
||
|
||
o 32-bit RISC performance using ARM® Cortex™-M3 v7M architecture
|
||
- 50-MHz operation
|
||
- Hardware-division and single-cycle-multiplication
|
||
- Integrated Nested Vectored Interrupt Controller (NVIC)
|
||
- 42 interrupt channels with eight priority levels
|
||
o 96 KB single-cycle flash
|
||
o 32 KB single-cycle SRAM
|
||
o Three general-purpose 32-bit timers
|
||
o Integrated Ethernet MAC and PHY
|
||
o Two fully programmable 16C550-type UARTs
|
||
o Three 10-bit channels (inputs) when used as single-ended inputs
|
||
o Two independent integrated analog comparators
|
||
o One I2C module
|
||
o One PWM generator block
|
||
– One 16-bit counter
|
||
– Two comparators
|
||
– Produces two independent PWM signals
|
||
– One dead-band generator
|
||
o 0 to 43 GPIOs, depending on user configuration
|
||
o On-chip low drop-out (LDO) voltage regulator
|
||
|
||
GPIO Usage
|
||
|
||
PIN SIGNAL Function
|
||
--- ----------------- ---------------------------------------
|
||
L3 PA0/U0RX UART0 receive
|
||
M3 PA1/U0TX UART0 transmit
|
||
E12 PB0/U0CTS UART0 CTS
|
||
D12 PB1/U0RTS UART0 RTS
|
||
L5 PA4/SPIRX SPI receive (pin hardwired to U1RX)
|
||
M5 PA5/SPITX SPI transmit (pin hardwired to U1TX)
|
||
H2 PD2/U1RX UART1 receive
|
||
H1 PD3/U1TX UART1 transmit
|
||
L4 PA3/U1CTS/SPICLK UART1 CTS or SPI clock
|
||
M4 PA2/U1RTS/SPISEL UART1 RTS or SPI slave select
|
||
J11 PF0/LED1 Ethernet LED1 (green)
|
||
J12 PF1/LED0 Ethernet LED0 (yellow)
|
||
C11 PB2 Transciever #INVALID
|
||
C12 PB3 Transciever #ENABLE
|
||
A6 PB4 Transciever ON
|
||
B7 PB5 Transciever #OFF
|
||
|
||
Development Environment
|
||
^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
Either Linux, Mac OS X or Cygwin on Windows can be used for the development
|
||
environment.
|
||
The source has been built only using the GNU toolchain (see below). Other
|
||
toolchains will likely cause problems. Testing was performed using GCC on
|
||
Mac OS X.
|
||
|
||
GNU Toolchain Options
|
||
^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
The NuttX make system has been modified to support the following different
|
||
toolchain options.
|
||
|
||
1. The CodeSourcery GNU toolchain,
|
||
2. The devkitARM GNU toolchain,
|
||
3. The NuttX buildroot Toolchain (see below).
|
||
|
||
To use a specific toolchain, you simply need to add one of the following
|
||
configuration options to your .config (or defconfig) file:
|
||
|
||
CONFIG_LM3S_CODESOURCERYW=y : CodeSourcery under Windows
|
||
CONFIG_LM3S_CODESOURCERYL=y : CodeSourcery under Linux or on Mac OS X.
|
||
CONFIG_LM3S_DEVKITARM=y : devkitARM under Windows
|
||
CONFIG_LM3S_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
|
||
|
||
If you are not using CONFIG_LM3S_BUILDROOT, then you may also have to modify
|
||
the PATH in the setenv.h file if your make cannot find the tools.
|
||
|
||
NOTE: the CodeSourcery (for Windows) and devkitARM are Windows native toolchains.
|
||
The CodeSourcey (for Linux) and NuttX buildroot toolchains are Cygwin and/or Linux
|
||
native toolchains. There are several limitations to using a Windows based
|
||
toolchain in a Cygwin environment. The three biggest are:
|
||
|
||
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
|
||
performed automatically in the Cygwin makefiles using the 'cygpath' utility
|
||
but you might easily find some new path problems. If so, check out 'cygpath -w'
|
||
|
||
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
|
||
are used in Nuttx (e.g., include/arch). The make system works around these
|
||
problems for the Windows tools by copying directories instead of linking them.
|
||
But this can also cause some confusion for you: For example, you may edit
|
||
a file in a "linked" directory and find that your changes had no effect.
|
||
That is because you are building the copy of the file in the "fake" symbolic
|
||
directory. If you use a Windows toolchain, you should get in the habit of
|
||
making like this:
|
||
|
||
make clean_context all
|
||
|
||
An alias in your .bashrc file might make that less painful.
|
||
|
||
3. Dependencies are not made when using Windows versions of the GCC. This is
|
||
because the dependencies are generated using Windows pathes which do not
|
||
work with the Cygwin make.
|
||
|
||
Support has been added for making dependencies with the windows-native toolchains.
|
||
That support can be enabled by modifying your Make.defs file as follows:
|
||
|
||
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
|
||
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
|
||
|
||
If you have problems with the dependency build (for example, if you are not
|
||
building on C:), then you may need to modify tools/mkdeps.sh
|
||
|
||
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
|
||
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
|
||
-Os.
|
||
|
||
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
|
||
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
|
||
path or will get the wrong version of make.
|
||
|
||
IDEs
|
||
^^^^
|
||
|
||
NuttX is built using command-line make. It can be used with an IDE, but some
|
||
effort will be required to create the project.
|
||
|
||
Makefile Build
|
||
--------------
|
||
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
|
||
simply use the NuttX makefile to build the system. That is almost for free
|
||
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
|
||
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
|
||
there is a lot of help on the internet).
|
||
|
||
Native Build
|
||
------------
|
||
Here are a few tips before you start that effort:
|
||
|
||
1) Select the toolchain that you will be using in your .config file
|
||
2) Start the NuttX build at least one time from the Cygwin command line
|
||
before trying to create your project. This is necessary to create
|
||
certain auto-generated files and directories that will be needed.
|
||
3) Set up include pathes: You will need include/, arch/arm/src/lm3s,
|
||
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
|
||
4) All assembly files need to have the definition option -D __ASSEMBLY__
|
||
on the command line.
|
||
|
||
Startup files will probably cause you some headaches. The NuttX startup file
|
||
is arch/arm/src/lm3s/lm3s_vectors.S.
|
||
|
||
NuttX buildroot Toolchain
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
||
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
|
||
different from the default in your PATH variable).
|
||
|
||
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
|
||
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
||
This GNU toolchain builds and executes in the Linux or Cygwin environment.
|
||
|
||
This port was tested with tools built using summon-arm-toolchain; available
|
||
from https://github.com/esden/summon-arm-toolchain, however the buildroot
|
||
instructions should apply for other platforms.
|
||
|
||
1. You must have already configured Nuttx in <some-dir>/nuttx.
|
||
|
||
cd tools
|
||
./configure.sh lm3s6432-s2e/<sub-dir>
|
||
|
||
2. Download the latest buildroot package into <some-dir>
|
||
|
||
3. unpack the buildroot tarball. The resulting directory may
|
||
have versioning information on it like buildroot-x.y.z. If so,
|
||
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
|
||
|
||
4. cd <some-dir>/buildroot
|
||
|
||
5. cp configs/cortexm3-defconfig-4.3.3 .config
|
||
|
||
6. make oldconfig
|
||
|
||
7. make
|
||
|
||
8. Edit setenv.h, if necessary, so that the PATH variable includes
|
||
the path to the newly built binaries.
|
||
|
||
See the file configs/README.txt in the buildroot source tree. That has more
|
||
detailed PLUS some special instructions that you will need to follow if you
|
||
are building a Cortex-M3 toolchain for Cygwin under Windows.
|
||
|
||
NOTE: This is an OABI toolchain.
|
||
|
||
|
||
Stellaris MDL-S2E Reference Design Configuration Options
|
||
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
||
|
||
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
||
be set to:
|
||
|
||
CONFIG_ARCH=arm
|
||
|
||
CONFIG_ARCH_family - For use in C code:
|
||
|
||
CONFIG_ARCH_ARM=y
|
||
|
||
CONFIG_ARCH_architecture - For use in C code:
|
||
|
||
CONFIG_ARCH_CORTEXM3=y
|
||
|
||
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
||
|
||
CONFIG_ARCH_CHIP=lm3s
|
||
|
||
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
|
||
chip:
|
||
|
||
CONFIG_ARCH_CHIP_LM3S6432
|
||
|
||
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
||
hence, the board that supports the particular chip or SoC.
|
||
|
||
CONFIG_ARCH_BOARD=lm3s6432-s2e (for the Stellaris MDL-S2E Reference Design)
|
||
|
||
CONFIG_ARCH_BOARD_name - For use in C code
|
||
|
||
CONFIG_ARCH_BOARD_LM3S6432S2E
|
||
|
||
CONFIG_ARCH_LOOPSPERMSEC - As supplied, calibrated for correct operation
|
||
of delay loops assuming 50MHz CPU frequency.
|
||
|
||
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
||
endian)
|
||
|
||
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
|
||
|
||
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
|
||
|
||
CONFIG_DRAM_START - The start address of installed DRAM
|
||
|
||
CONFIG_DRAM_START=0x20000000
|
||
|
||
CONFIG_DRAM_END - Last address+1 of installed RAM
|
||
|
||
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
|
||
|
||
CONFIG_ARCH_IRQPRIO - The LM3S6918 supports interrupt prioritization
|
||
|
||
CONFIG_ARCH_IRQPRIO=y
|
||
|
||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
||
have LEDs
|
||
|
||
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
||
stack. If defined, this symbol is the size of the interrupt
|
||
stack in bytes. If not defined, the user task stacks will be
|
||
used during interrupt handling.
|
||
|
||
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
||
|
||
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
|
||
|
||
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
||
cause a 100 second delay during boot-up. This 100 second delay
|
||
serves no purpose other than it allows you to calibratre
|
||
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
||
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
||
the delay actually is 100 seconds.
|
||
|
||
There are configurations for disabling support for interrupts GPIO ports.
|
||
GPIOH and GPIOJ must be disabled because they do not exist on the LM3S6432.
|
||
Additional interrupt support can be disabled if desired to reduce memory
|
||
footprint - GPIOs C-G are not pinned out on the MDL-S2E board.
|
||
|
||
CONFIG_LM3S_DISABLE_GPIOA_IRQS=n
|
||
CONFIG_LM3S_DISABLE_GPIOB_IRQS=n
|
||
CONFIG_LM3S_DISABLE_GPIOC_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOD_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOE_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOF_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOG_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOH_IRQS=y
|
||
CONFIG_LM3S_DISABLE_GPIOJ_IRQS=y
|
||
|
||
LM3S6432 specific device driver settings
|
||
|
||
CONFIG_UARTn_DISABLE
|
||
The TX and RX pins for UART1 share I/O pins with the TX and RX pins
|
||
for SSI0. To avoid conflicts, only one of SSI0 and UART1 should
|
||
be enabled in a configuration.
|
||
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
||
console and ttys0 (default is UART1).
|
||
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
||
This specific the size of the receive buffer
|
||
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
||
being sent. This specific the size of the transmit buffer
|
||
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
||
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
||
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
||
CONFIG_UARTn_2STOP - Two stop bits
|
||
|
||
CONFIG_SSI0_DISABLE - Select to disable support for SSI0
|
||
The TX and RX pins for SSI0 share I/O pins with the TX and RX pins
|
||
for UART1. To avoid conflicts, only one of SSI0 and UART1 should
|
||
be enabled in a configuration.
|
||
CONFIG_SSI1_DISABLE - Select to disable support for SSI1
|
||
Note that the LM3S6432 only has one SSI, so SSI1 should always be
|
||
disabled.
|
||
CONFIG_SSI_POLLWAIT - Select to disable interrupt driven SSI support.
|
||
Poll-waiting is recommended if the interrupt rate would be to
|
||
high in the interrupt driven case.
|
||
CONFIG_SSI_TXLIMIT - Write this many words to the Tx FIFO before
|
||
emptying the Rx FIFO. If the SPI frequency is high and this
|
||
value is large, then larger values of this setting may cause
|
||
Rx FIFO overrun errors. Default: half of the Tx FIFO size (4).
|
||
|
||
CONFIG_LM3S_ETHERNET - This must be set (along with CONFIG_NET)
|
||
to build the LM3S Ethernet driver
|
||
CONFIG_LM3S_ETHLEDS - Enable to use Ethernet LEDs on the board.
|
||
CONFIG_LM3S_BOARDMAC - This should be set in order to use the
|
||
MAC address configured in the flash USER registers.
|
||
CONFIG_LM3S_ETHHDUPLEX - Set to force half duplex operation
|
||
CONFIG_LM3S_ETHNOAUTOCRC - Set to suppress auto-CRC generation
|
||
CONFIG_LM3S_ETHNOPAD - Set to suppress Tx padding
|
||
CONFIG_LM3S_MULTICAST - Set to enable multicast frames
|
||
CONFIG_LM3S_PROMISCUOUS - Set to enable promiscuous mode
|
||
CONFIG_LM3S_BADCRC - Set to enable bad CRC rejection.
|
||
CONFIG_LM3S_DUMPPACKET - Dump each packet received/sent to the console.
|
||
|
||
Configurations
|
||
^^^^^^^^^^^^^^
|
||
|
||
Each Stellaris MDL-S2E Reference Design configuration is maintained in a
|
||
sudirectory and can be selected as follow:
|
||
|
||
cd tools
|
||
./configure.sh lm3s6432-s2e/<subdir>
|
||
cd -
|
||
. ./setenv.sh
|
||
|
||
Where <subdir> is one of the following:
|
||
|
||
nsh:
|
||
Configures the NuttShell (nsh) located at examples/nsh. The
|
||
Configuration enables both the serial and telnetd NSH interfaces.
|
||
|
||
NOTE: As it is configured now, you MUST have a network connected.
|
||
Otherwise, the NSH prompt will not come up because the Ethernet
|
||
driver is waiting for the network to come up. That is probably
|
||
a bug in the Ethernet driver behavior!
|
||
|
||
ostest:
|
||
This configuration directory, performs a simple OS test using
|
||
examples/ostest.
|
||
|
||
NOTE: as the configuration stands, ostest will hang during the
|
||
semaphore test. This has not been debugged.
|