82 lines
2.7 KiB
Plaintext
82 lines
2.7 KiB
Plaintext
compal_e99
|
|
==========
|
|
|
|
This directory contains the board support for compal e99 phones.
|
|
|
|
This port is based on patches contributed by Denis Carikli for both the
|
|
compal e99 and e88. At the time of initial check-in, the following phones
|
|
were tested:
|
|
|
|
* Motorola c155 (compal e99) with the compalram and highram configuration
|
|
* Motorola W220 (compal e88)
|
|
* The openmoko freerunner baseband(compal e88)
|
|
|
|
The patches were made by Alan Carvalho de Assis and Denis Carikli using
|
|
the Stefan Richter's patches that can be found here:
|
|
|
|
http://cgit.osmocom.org/cgit/nuttx-bb/log/?h=lputt%2Ftesting
|
|
|
|
Osmocom-BB Dependencies and Sercomm
|
|
===================================
|
|
|
|
The build environment assumes that you have the osmocom-bb project
|
|
directory at same level as the nuttx project:
|
|
|
|
|- nuttx
|
|
|- apps
|
|
`- osmocom-bb
|
|
|
|
If you attempt to build this configuration without osmocom-bb, and that
|
|
you added support for sercomm in your configuration(CONFIG_SERCOMM_CONSOLE=y)
|
|
you will get compilation errors in drivers/sercomm due to header files that
|
|
are needed from the osmocom-bb directory.
|
|
|
|
By default, NuttX will not use sercomm (HDLC protocol) to communicate with
|
|
the host system. Sercomm is the transport used by osmocom-bb that runs on top
|
|
of serial. See http://bb.osmocom.org/trac/wiki/nuttx-bb/run for detailed
|
|
the usage of nuttx with sercomm.
|
|
|
|
Loading NuttX
|
|
=============
|
|
|
|
The osmocom-bb wiki describes how to load NuttX. See
|
|
http://bb.osmocom.org/trac/wiki/nuttx-bb for detailed information.
|
|
The way that nuttx is loaded depends on the configuration (highram/compalram)
|
|
and phone:
|
|
|
|
o compalram is for the ramloader(for phone having a bootloader on flash)
|
|
o highram is for phones having the romloader(if the phone has a bootrom)
|
|
or for loading in the ram trough a special loader(loaded first on ram
|
|
by talking to the ramloader) when having a ramloader(which can only
|
|
load 64k).
|
|
|
|
Configurations
|
|
==============
|
|
|
|
1. Each Compal E99 configuration is maintained in a sub-directory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh compal_e99/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the configuration sub-directories under
|
|
nuttx/configs/compal_e99.
|
|
|
|
2. These configurations use the mconf-based configuration tool. To
|
|
change a configurations using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt
|
|
and misc/tools/
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
3. By default, all configurations assume the NuttX Buildroot toolchain
|
|
under Linux (should work under Windows with Cygwin as well). This
|
|
is easily reconfigured:
|
|
|
|
CONFIG_HOST_LINUX=y
|
|
CONFIG_ARM_TOOLCHAIN_BUILDROOT=y
|