258 lines
8.7 KiB
ReStructuredText
258 lines
8.7 KiB
ReStructuredText
================
|
||
ST Nucle H743ZI2
|
||
================
|
||
|
||
This page discusses issues unique to NuttX configurations for the
|
||
STMicro NUCLEO-H743ZI2 development board featuring the STM32H743ZI
|
||
MCU. The STM32H743ZI is a 400MHz Cortex-M7 operation with 2MBytes Flash
|
||
memory and 1MByte SRAM. The board features:
|
||
|
||
- On-board ST-LINK/V2 for programming and debugging,
|
||
- 3 user LEDs
|
||
- Two pushbuttons (user and reset)
|
||
- 32.768 kHz crystal oscillator
|
||
- USB OTG FS with Micro-AB connectors
|
||
- Ethernet connector compliant with IEEE-802.3-2002
|
||
- Board connectors:
|
||
- USB with Micro-AB
|
||
- SWD
|
||
- Ethernet RJ45
|
||
- ST Zio connector including Arduino Uno V3
|
||
- ST morpho
|
||
|
||
Refer to the http://www.st.com website for further information about this
|
||
board (search keyword: NUCLEO-H743ZI2)
|
||
|
||
Serial Console
|
||
==============
|
||
|
||
Many options are available for a serial console via the Morpho connector.
|
||
Here two common serial console options are suggested:
|
||
|
||
1. Arduino Serial Shield.
|
||
|
||
If you are using a standard Arduino RS-232 shield with the serial
|
||
interface with RX on pin D0 and TX on pin D1 from USART6:
|
||
|
||
======== ========= =====
|
||
ARDUINO FUNCTION GPIO
|
||
======== ========= =====
|
||
DO RX USART6_RX PG9
|
||
D1 TX USART6_TX PG14
|
||
======== ========= =====
|
||
|
||
2. Nucleo Virtual Console.
|
||
|
||
The virtual console uses Serial Port 3 (USART3) with TX on PD8 and RX on
|
||
PD9.
|
||
|
||
================= ===
|
||
VCOM Signal Pin
|
||
================= ===
|
||
SERIAL_RX PD9
|
||
SERIAL_TX PD8
|
||
================= ===
|
||
|
||
These signals are internally connected to the on board ST-Link.
|
||
|
||
The Nucleo virtual console is the default serial console in all
|
||
configurations unless otherwise stated in the description of the
|
||
configuration.
|
||
|
||
Configurations
|
||
==============
|
||
|
||
nsh:
|
||
----
|
||
|
||
This configuration provides a basic NuttShell configuration (NSH)
|
||
for the Nucleo-H743ZI. The default console is the VCOM on USART3.
|
||
|
||
jumbo:
|
||
------
|
||
|
||
This configuration enables many Apache NuttX features. This is
|
||
mostly to help provide additional code coverage in CI, but also
|
||
allows for a users to see a wide range of features that are
|
||
supported by the OS.
|
||
|
||
Some highlights:
|
||
NSH:
|
||
- Readline with tab completion
|
||
- Readline command history
|
||
|
||
Performance and Monitoring:
|
||
- RAM backed syslog
|
||
- Syslog with process name, priority, and timestamp
|
||
- Process Snapshot with stack usage, cpu usage, and signal information
|
||
- Interrupt Statistics
|
||
- procfs filesystem (required for ifconfig, ifup/ifdown)
|
||
|
||
Networking:
|
||
- IPv4 Networking
|
||
- Ethernet
|
||
- DHCP Client
|
||
- iperf
|
||
- telnet daemon
|
||
|
||
File Systems:
|
||
- FAT filesystem
|
||
- LittleFS
|
||
- RAM MTD device
|
||
|
||
Testing:
|
||
- OS Test with FPU support
|
||
- Filesystem testing
|
||
|
||
USB Host:
|
||
- USB Hub support
|
||
- Mass Storage Device
|
||
- Trace Monitoring
|
||
|
||
|
||
..
|
||
NuttShell (NSH) NuttX-10.0.1
|
||
nsh> uname -a
|
||
NuttX 10.0.1 3ab35e48ff-dirty Mar 28 2021 15:35:29 arm nucleo-h743zi2
|
||
nsh> ?
|
||
help usage: help [-v] [<cmd>]
|
||
|
||
. cd dmesg hexdump mkrd reboot telnetd xd
|
||
[ cp echo ifconfig mh rm time
|
||
? cmp env irqinfo mount rmdir true
|
||
addroute dirname exec kill mv route uname
|
||
arp date exit ls mw set umount
|
||
basename dd false mb nslookup sleep unset
|
||
break delroute free mkdir ps source usleep
|
||
cat df help mkfatfs pwd test wget
|
||
|
||
Builtin Apps:
|
||
fstest getprime nsh ostest ping renew sh
|
||
nsh> ps
|
||
PID PRI POLICY TYPE NPX STATE EVENT SIGMASK STACK USED FILLED CPU COMMAND
|
||
0 0 FIFO Kthread N-- Ready 00000000 001024 000472 46.0% 100.0% Idle Task
|
||
1 224 RR Kthread --- Waiting Signal 00000000 002036 000456 22.3% 0.0% hpwork
|
||
2 100 RR Kthread --- Waiting Signal 00000000 002036 000680 33.3% 0.0% lpwork
|
||
3 100 RR Task --- Running 00000000 004084 001304 31.9% 0.0% init
|
||
4 100 RR Kthread --- Waiting Semaphore 00000000 002036 000752 36.9% 0.0% usbhost
|
||
5 50 RR Kthread --- Waiting Signal 00000000 004076 000472 11.5% 0.0% USB Monitor
|
||
6 100 RR Task --- Waiting Semaphore 00000000 002012 000648 32.2% 0.0% Telnet daemon 0x38005600
|
||
nsh> free
|
||
total used free largest
|
||
Umem: 944336 159520 784816 451712
|
||
nsh> irqinfo
|
||
IRQ HANDLER ARGUMENT COUNT RATE TIME
|
||
3 080011ed 00000000 1599 20.405 0
|
||
15 08004e0d 00000000 7836 100.000 10000
|
||
55 08000799 24000000 1122 14.318 0
|
||
77 0800580b 00000000 14 0.178 0
|
||
117 0802c6f1 00000000 1372 17.544 0
|
||
nsh> date; sleep 2; date
|
||
Thu, Jan 01 00:01:50 1970
|
||
Thu, Jan 01 00:01:52 1970
|
||
nsh> ifconfig
|
||
eth0 Link encap:Ethernet HWaddr 46:fd:66:78:aa:54 at UP
|
||
inet addr:10.0.0.2 DRaddr:10.0.0.1 Mask:255.255.255.0
|
||
|
||
lo Link encap:Local Loopback at UP
|
||
inet addr:127.0.0.1 DRaddr:127.0.0.1 Mask:255.0.0.0
|
||
|
||
IPv4 TCP UDP ICMP
|
||
Received 0004 0000 0004 0000
|
||
Dropped 0000 0000 0000 0000
|
||
IPv4 VHL: 0000 Frg: 0000
|
||
Checksum 0000 0000 0000 ----
|
||
TCP ACK: 0000 SYN: 0000
|
||
RST: 0000 0000
|
||
Type 0000 ---- ---- 0000
|
||
Sent 0000 0000 0000 0000
|
||
Rexmit ---- 0000 ---- ----
|
||
nsh> renew eth0
|
||
nsh> ifconfig
|
||
eth0 Link encap:Ethernet HWaddr 46:fd:66:78:aa:54 at UP
|
||
inet addr:192.168.86.249 DRaddr:192.168.86.1 Mask:255.255.255.0
|
||
|
||
lo Link encap:Local Loopback at UP
|
||
inet addr:127.0.0.1 DRaddr:127.0.0.1 Mask:255.0.0.0
|
||
|
||
IPv4 TCP UDP ICMP
|
||
Received 0007 0000 0007 0000
|
||
Dropped 0000 0000 0000 0000
|
||
IPv4 VHL: 0000 Frg: 0000
|
||
Checksum 0000 0000 0000 ----
|
||
TCP ACK: 0000 SYN: 0000
|
||
RST: 0000 0000
|
||
Type 0000 ---- ---- 0000
|
||
Sent 0002 0000 0002 0000
|
||
Rexmit ---- 0000 ---- ----
|
||
nsh> ping www.google.com
|
||
PING 172.217.14.196 56 bytes of data
|
||
56 bytes from 172.217.14.196: icmp_seq=0 time=10 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=1 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=2 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=3 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=4 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=5 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=6 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=7 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=8 time=0 ms
|
||
56 bytes from 172.217.14.196: icmp_seq=9 time=0 ms
|
||
10 packets transmitted, 10 received, 0% packet loss, time 10100 ms
|
||
nsh>
|
||
nsh> ls /dev
|
||
/dev:
|
||
console
|
||
null
|
||
ramlog
|
||
rammtd
|
||
sda
|
||
telnet
|
||
ttyS0
|
||
nsh> ls /mnt
|
||
/mnt:
|
||
lfs/
|
||
nsh> echo "This will go away on reboot." > /mnt/lfs/afile
|
||
nsh> cat /mnt/lfs/afile
|
||
This will go away on reboot.
|
||
nsh> mount -t vfat /dev/sda /mnt/sda
|
||
nsh> echo "This will stay on the USB drive" > /mnt/sda/afile
|
||
nsh> ls /mnt/sda
|
||
/mnt/sda:
|
||
afile
|
||
nsh> reboot
|
||
|
||
NuttShell (NSH) NuttX-10.0.1
|
||
nsh> mount -t vfat /dev/sda /mnt/sda
|
||
nsh> ls /mnt/lfs
|
||
/mnt/lfs:
|
||
.
|
||
..
|
||
nsh> ls /mnt/sda
|
||
/mnt/sda:
|
||
afile
|
||
nsh> cat /mnt/sda/afile
|
||
This will stay on the USB drive
|
||
nsh>
|
||
```
|
||
|
||
```
|
||
❯ telnet 192.168.86.249
|
||
Trying 192.168.86.249...
|
||
Connected to 192.168.86.249.
|
||
Escape character is '^]'.
|
||
|
||
NuttShell (NSH) NuttX-10.0.1
|
||
nsh> ps
|
||
PID PRI POLICY TYPE NPX STATE EVENT SIGMASK STACK USED FILLED CPU COMMAND
|
||
0 0 FIFO Kthread N-- Ready 00000000 001024 000472 46.0% 100.0% Idle Task
|
||
1 224 RR Kthread --- Waiting Signal 00000000 002036 000456 22.3% 0.0% hpwork
|
||
2 100 RR Kthread --- Waiting Signal 00000000 002036 000680 33.3% 0.0% lpwork
|
||
3 100 RR Task --- Waiting Semaphore 00000000 004084 001304 31.9% 0.0% init
|
||
4 100 RR Kthread --- Waiting Semaphore 00000000 002036 000752 36.9% 0.0% usbhost
|
||
5 50 RR Kthread --- Waiting Signal 00000000 004076 000472 11.5% 0.0% USB Monitor
|
||
6 100 RR Task --- Waiting Semaphore 00000000 002012 000648 32.2% 0.0% Telnet daemon 0x38005600
|
||
9 100 RR Kthread --- Waiting Semaphore 00000000 001004 000448 44.6% 0.0% telnet_io
|
||
10 100 RR Task --- Running 00000000 002028 001328 65.4% 0.0% Telnet session
|
||
nsh>
|
||
```
|