211 lines
6.7 KiB
ReStructuredText
211 lines
6.7 KiB
ReStructuredText
=================
|
|
Olimex STM32-E407
|
|
=================
|
|
|
|
The Olimex STM32-E407 configuration is based on the configuration
|
|
olimex-stm32-h407 and stm32f4discovery.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Instantiating Configurations
|
|
----------------------------
|
|
|
|
Each Olimex-STM32-E407 configuration is maintained in a sub-directory and
|
|
can be selected as follow::
|
|
|
|
tools/configure.sh [OPTIONS] olimex-stm32-e407:<subdir>
|
|
|
|
Typical options include -l for a Linux host platform or -c for Cygwin
|
|
host platform. See 'tools/configure.sh -h' for other options. And
|
|
<subdir> is one of the sub-directories listed below.
|
|
|
|
Compile Firmware
|
|
----------------
|
|
|
|
Once you've set the proper configuration, you just need to execute the next
|
|
command::
|
|
|
|
make
|
|
|
|
If everything goes find, it should return the next two files::
|
|
|
|
nuttx.hex
|
|
nuttx.bin
|
|
|
|
You can return more kinds of files by setting on menuconfig.
|
|
|
|
Flashing the Board
|
|
------------------
|
|
|
|
You can flash this board in different ways, but the easiest way is using
|
|
ARM-USB-TINY-H JTAG flasher device.
|
|
Connect this device to the JTAG connector and type the next command::
|
|
|
|
openocd -f interface/ftdi/olimex-arm-usb-tiny-h.cfg -f target/stm32f4x.cfg -c init -c "reset halt" -c "flash write_image erase nuttx.bin 0x08000000"
|
|
|
|
Configuration Directories
|
|
-------------------------
|
|
|
|
nsh
|
|
---
|
|
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. This
|
|
configuration enables a console on UART2. Support for
|
|
builtin applications is enabled, but in the base configuration no
|
|
builtin applications are selected.
|
|
|
|
usbnsh
|
|
------
|
|
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. This
|
|
configuration enables a console on USB_OTG1. Support for
|
|
builtin applications is enabled, but in the base configuration no
|
|
builtin applications are selected.
|
|
|
|
netnsh
|
|
------
|
|
|
|
Configures the NuttShell (nsh) located at examples/nsh. This
|
|
configuration is focused on network testing.
|
|
|
|
bmp180
|
|
------
|
|
|
|
This is a configuration example for the BMP180 barometer sensor. This
|
|
sensor works with I2C, you need to do the next connections::
|
|
|
|
BMP180 VIN -> Board 3.3V
|
|
BMP180 GND -> Board GND
|
|
BMP180 SCL -> Board PB6 (Arduino header D1)
|
|
BMP180 SDA -> Board PB7 (Arduino header D0)
|
|
|
|
This example is configured to work with the USBNSH instead of UART NSH, so
|
|
the console will be shown over the USB_OTG1 connector.
|
|
|
|
On the console, type "ls /dev " and if the registration process goes fine,
|
|
you should see a device called "press0". Now execute the app
|
|
BMP180 to see the ambient pressure value.
|
|
|
|
dac
|
|
---
|
|
|
|
This is a configuration example to use the DAC1 of the board. The DAC1
|
|
is attached to the PA4 pin (Arduino header D10).
|
|
|
|
This example is configured to work with the USBNSH instead of UART NSH, so
|
|
the console will be shown over the USB_OTG1 connector.
|
|
|
|
On the console, type "ls /dev " and if the registration process goes fine,
|
|
you should see a device called "dac0". Now execute the app
|
|
dac put a value at the output.
|
|
|
|
ina219
|
|
------
|
|
|
|
This is a configuration example for the INA219 DC current sensor. This
|
|
sensor works with I2C, you need to do the next connections::
|
|
|
|
INA219 VIN -> Board 3.3V
|
|
INA219 GND -> Board GND
|
|
INA219 SCL -> Board PB6 (Arduino header D1)
|
|
INA219 SDA -> Board PB7 (Arduino header D0)
|
|
|
|
This example is configured to work with the USBNSH instead of UART NSH, so
|
|
the console will be shown over the USB_OTG1 connector.
|
|
|
|
On the console, type "ls /dev " and if the registration process goes fine,
|
|
you should see a device called "ina219". Now execute the app
|
|
ina219 to see the ambient pressure value.
|
|
|
|
timer
|
|
-----
|
|
|
|
This configuration set the proper configuration to use the timer1 of the
|
|
board. This example is configured to work with the USBNSH instead of
|
|
UART NSH, so the console will be shown over the USB_OTG1 connector.
|
|
|
|
On the console, type "ls /dev " and if the registration process goes fine,
|
|
you should see a device called "timer1".
|
|
|
|
mrf24j40-mac
|
|
------------
|
|
|
|
This configuration set the proper configuration to set the 802.15.4
|
|
communication layer with the MRF24J40 radio. This radio works with
|
|
SPI, you need to do the next connections::
|
|
|
|
MRF24J40 VCC -> Board 3.3V
|
|
MRF24J40 GND -> Board GND
|
|
MRF24J40 SCLK -> Board PA5 (Arduino header D13)
|
|
MRF24J40 MISO -> Board PA6 (Arduino header D12)
|
|
MRF24J40 MOSI -> Board PB5 (Arduino header D11)
|
|
MRF24J40 CS -> Board PA4 (Arduino header D10)
|
|
MRF24J40 INT -> Board PG12 (Arduino header D8)
|
|
|
|
This example is configured to work with the USBNSH instead of UART NSH,
|
|
so the console will be shown over the USB_OTG1 connector.
|
|
|
|
Once you're on the console, you need to check if the initialization
|
|
process was fine. To do so, you need to type "ls /dev" and you should
|
|
see a device call "ieee0". At this point we need to set-up the network,
|
|
follow the next steps::
|
|
|
|
This is an example of how to configure a coordinator:
|
|
i8sak /dev/ieee0 startpan cd:ab
|
|
i8sak set chan 11
|
|
i8sak set saddr 42:01
|
|
i8sak acceptassoc
|
|
|
|
This is an example of how to configure the endpoint:
|
|
i8sak /dev/ieee0
|
|
i8sak set chan 11
|
|
i8sak set panid cd:ab
|
|
i8sak set saddr 42:02
|
|
i8sak set ep_saddr 42:01
|
|
i8sak assoc
|
|
|
|
mrf24j40-6lowpan
|
|
----------------
|
|
|
|
This configuration set the proper configuration to use 6lowpan protocol with the MRF24J40
|
|
radio. This radio works with SPI, you need to do the next connections::
|
|
|
|
MRF24J40 VCC -> Board 3.3V
|
|
MRF24J40 GND -> Board GND
|
|
MRF24J40 SCLK -> Board PA5 (Arduino header D13)
|
|
MRF24J40 MISO -> Board PA6 (Arduino header D12)
|
|
MRF24J40 MOSI -> Board PB5 (Arduino header D11)
|
|
MRF24J40 CS -> Board PA4 (Arduino header D10)
|
|
MRF24J40 INT -> Board PG12 (Arduino header D8)
|
|
|
|
This example is configured to work with the USBNSH instead of UART NSH, so
|
|
the console will be shown over the USB_OTG1 connector.
|
|
|
|
Once you're on the console, you need to check if the initialization process
|
|
was fine. To do so, you need to type "ls /dev" and you should see a device
|
|
call "ieee0". At this point we need to set-up the network, follow the next steps::
|
|
|
|
This is an example of how to configure a coordinator:
|
|
i8sak wpan0 startpan cd:ab
|
|
i8sak set chan 11
|
|
i8sak set saddr 42:01
|
|
i8sak acceptassoc
|
|
|
|
When the association was complete, you need to bring-up the network:
|
|
ifup wpan0
|
|
|
|
This is an example of how to configure the endpoint:
|
|
i8sak wpan0
|
|
i8sak set chan 11
|
|
i8sak set panid cd:ab
|
|
i8sak set saddr 42:02
|
|
i8sak set ep_saddr 42:01
|
|
i8sak assoc
|
|
|
|
When the association was complete, you need to bring-up the network:
|
|
ifup wpan0
|
|
|
|
If you execute the command "ifconfig", you will be able to see the info of the WPAN0 interface
|
|
and see the assigned IP. This interface can be use with an UDP or TCP server/client application.
|