incubator-nuttx/boards/z16/z16f/z16f2800100zcog/include/board.h

113 lines
4.1 KiB
C

/****************************************************************************
* boards/z16/z16f/z16f2800100zcog/include/board.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_Z16_Z16F2811_Z16F2800100ZCOG_INCLUDE_BOARD_H
#define __BOARDS_Z16_Z16F2811_Z16F2800100ZCOG_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* The Z16F2800100ZCOG board has a 20MHz crystal. The ZNEO clocking will be
* configured to use this crystal frequency directly as the clock source
*/
#define BOARD_XTAL_FREQUENCY 20000000 /* 20MHz */
#define BOARD_CLKSRC 1 /* Clock source = external crystal */
#define BOARD_SYSTEM_FREQUENCY BOARD_XTAL_FREQUENCY
/* Flash option bits
*
* "Each time the option bits are programmed or erased, the device must be
* Reset for the change to take place. During any reset operation .., the
* option bits are automatically read from the Program memory and written
* to Option Configuration registers. ... Option Bit Control Register are
* loaded before the device exits Reset and the ZNEO CPU begins code
* execution. The Option Configuration registers are not part of the
* Register file and are not accessible for read or write access."
*/
#ifndef __ASSEMBLY__
# define BOARD_FLOPTION0 (Z16F_FLOPTION0_MAXPWR | Z16F_FLOPTION0_WDTRES | \
Z16F_FLOPTION0_WDTA0 | Z16F_FLOPTION0_VBOA0 | \
Z16F_FLOPTION0_DBGUART | Z16F_FLOPTION0_FWP | \
Z16F_FLOPTION0_RP)
# define BOARD_FLOPTION1 (Z16F_FLOPTION1_RESVD | Z16F_FLOPTION1_MCEN | \
Z16F_FLOPTION1_OFFH | Z16F_FLOPTION1_OFFL)
# define BOARD_FLOPTION2 Z16F_FLOPTION2_RESVD
# define BOARD_FLOPTION3 (Z16F_FLOPTION3_RESVD | Z16F_FLOPTION3_NORMAL | \
Z16F_FLOPTION3_ROMLESS)
/* The same settings, pre-digested for assembly language */
#else
# define BOARD_FLOPTION0 %ff
# define BOARD_FLOPTION1 %ff
# define BOARD_FLOPTION2 %ff
# define BOARD_FLOPTION3 %ff
#endif
/* LED pattern definitions
*
* The z16f2800100zcog board has four LEDs:
*
* - Green LED D1 which illuminates in the presence of Vcc
* - Red LED D2 connected to chip port PA0_T0IN
* - Yellow LED D3 connected to chip port PA1_T0OUT
* - Green LED D4 connected to chip port PA2_DE0
*/
#define LED_STARTED 0
#define LED_HEAPALLOCATE 1
#define LED_IRQSENABLED 2
#define LED_STACKCREATED 3
#define LED_IDLE 4
#define LED_INIRQ 5
#define LED_SIGNAL 6
#define LED_ASSERTION 7
#define LED_PANIC 8
/****************************************************************************
* Public Functions Definitions
****************************************************************************/
#undef EXTERN
#if defined(__cplusplus)
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
#undef EXTERN
#if defined(__cplusplus)
}
#endif
#endif /* __BOARDS_Z16_Z16F2811_Z16F2800100ZCOG_INCLUDE_BOARD_H */