139 lines
3.8 KiB
Plaintext
139 lines
3.8 KiB
Plaintext
README
|
|
^^^^^^
|
|
|
|
Toolchain
|
|
^^^^^^^^^
|
|
|
|
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
|
|
be modified to point to the correct path to the ARM920T GCC toolchain (if
|
|
different from the default).
|
|
|
|
If you have no ARM toolchain, one can be downloaded from the NuttX
|
|
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
|
|
|
|
1. You must have already configured Nuttx in <some-dir>nuttx.
|
|
|
|
cd tools
|
|
./configure.sh mx1ads/<sub-dir>
|
|
|
|
2. Download the latest buildroot package into <some-dir>
|
|
|
|
3. unpack
|
|
|
|
4. cd <some-dir>/buildroot
|
|
|
|
5. cp configs/arm920t-defconfig-4.2.4 .config
|
|
|
|
6. make oldconfig
|
|
|
|
7. make
|
|
|
|
8. Edit setenv.h so that the PATH variable includes the path to the
|
|
newly built binaries.
|
|
|
|
ARM/i.MX1-specific Configuration Options
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
|
|
be set to:
|
|
|
|
CONFIG_ARCH=arm
|
|
|
|
CONFIG_ARCH_family - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM=y
|
|
|
|
CONFIG_ARCH_architecture - For use in C code:
|
|
|
|
CONFIG_ARCH_ARM920T=y
|
|
|
|
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
|
|
|
|
CONFIG_ARCH_CHIP=imx
|
|
|
|
CONFIG_ARCH_CHIP_name - For use in C code. Could be line _IMX1,
|
|
_IMXL, _IMX21, _IMX27, _IMX31, etc. (not all of which are
|
|
supported).
|
|
|
|
CONFIG_ARCH_CHIP_IMX1
|
|
|
|
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
|
|
hence, the board that supports the particular chip or SoC.
|
|
|
|
CONFIG_ARCH_BOARD=mx1ads (for the Freescale MX1ADS evaluation board)
|
|
|
|
CONFIG_ARCH_BOARD_name - For use in C code
|
|
|
|
CONFIG_ARCH_BOARD_MX1ADS (for the Spectrum Digital C5471 EVM)
|
|
|
|
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
|
|
of delay loops
|
|
|
|
CONFIG_ENDIAN_BIG - define if big endian (default is little
|
|
endian)
|
|
|
|
CONFIG_DRAM_SIZE - Describes the installed DRAM.
|
|
|
|
CONFIG_DRAM_START - The start address of installed DRAM
|
|
|
|
CONFIG_DRAM_VSTART - The startaddress of DRAM (virtual)
|
|
|
|
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
|
|
have LEDs
|
|
|
|
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
|
|
stack. If defined, this symbol is the size of the interrupt
|
|
stack in bytes. If not defined, the user task stacks will be
|
|
used during interrupt handling.
|
|
|
|
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
|
|
|
|
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
|
|
cause a 100 second delay during boot-up. This 100 second delay
|
|
serves no purpose other than it allows you to calibratre
|
|
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
|
|
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
|
|
the delay actually is 100 seconds.
|
|
|
|
IMX specific device driver settings
|
|
|
|
CONFIG_UARTn_SERIAL_CONSOLE - selects the UARTn for the
|
|
console and ttys0 (default is the UART0).
|
|
CONFIG_UARTn_RXBUFSIZE - Characters are buffered as received.
|
|
This specific the size of the receive buffer
|
|
CONFIG_UARTn_TXBUFSIZE - Characters are buffered before
|
|
being sent. This specific the size of the transmit buffer
|
|
CONFIG_UARTn_BAUD - The configure BAUD of the UART. Must be
|
|
CONFIG_UARTn_BITS - The number of bits. Must be either 7 or 8.
|
|
CONFIG_UARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
|
|
CONFIG_UARTn_2STOP - Two stop bits
|
|
|
|
IMX USB Configuration
|
|
|
|
CONFIG_IMX_GIO_USBATTACH
|
|
GIO that detects USB attach/detach events
|
|
CONFIG_IMX_GIO_USBDPPULLUP
|
|
GIO
|
|
CONFIG_DMA320_USBDEV_DMA
|
|
Enable IMX-specific DMA support
|
|
CONFIG_IMX_GIO_USBATTACH=6
|
|
|
|
Configurations
|
|
^^^^^^^^^^^^^^
|
|
|
|
Each MX1ADS configuration is maintained in a sudirectory and
|
|
can be selected as follow:
|
|
|
|
cd tools
|
|
./configure.sh imxads/<subdir>
|
|
cd -
|
|
. ./setenv.sh
|
|
|
|
Where <subdir> is one of the following:
|
|
|
|
ostest
|
|
^^^^^^
|
|
|
|
This configuration directory, performs a simple OS test using
|
|
examples/ostest.
|