163 lines
5.7 KiB
C
163 lines
5.7 KiB
C
/****************************************************************************
|
|
* boards/mips/pic32mx/mirtoo/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_MIPS_PIC32MX_MIRTOO_INCLUDE_BOARD_H
|
|
#define __BOARDS_MIPS_PIC32MX_MIRTOO_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdbool.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Configuration ************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* The Mirtoo does not use an external crystal but relies instead on the
|
|
* internal +/- 0.9% FRC clock. That clock has a nomninal frequency of 8MHz.
|
|
*/
|
|
|
|
#define BOARD_FRC_FREQ 8000000 /* FRC nominal frequency(8MHz) */
|
|
|
|
/* Oscillator modes */
|
|
|
|
#define BOARD_FNOSC_FRCPLL 1 /* Use FRC w/PLL module */
|
|
#define BOARD_POSC_DISABLED 1 /* Disable primary oscillator */
|
|
|
|
/* PLL configuration and resulting CPU clock.
|
|
* CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV
|
|
*/
|
|
|
|
#define BOARD_PLL_INPUT BOARD_FRC_FREQ
|
|
#define BOARD_PLL_IDIV 2 /* PLL input divider: Input = 4MHz */
|
|
#define BOARD_PLL_MULT 20 /* PLL multiplier: PLL = 80MHz */
|
|
#define BOARD_PLL_ODIV 2 /* PLL output divider: Output = 40MHz */
|
|
|
|
#define BOARD_CPU_CLOCK 40000000 /* CPU clock 40MHz = (((8MHz / 2) * 20) / 2) */
|
|
|
|
/* USB PLL configuration.
|
|
* USB_CLOCK = ((POSC_XTAL / IDIV) * 24) / 2
|
|
*/
|
|
|
|
#define BOARD_UPLL_IDIV 2 /* USB PLL divider (revisit) */
|
|
#define BOARD_USB_CLOCK 48000000 /* USB clock (8MHz / 2) * 24 / 2) */
|
|
|
|
/* Peripheral clock is divided down from CPU clock.
|
|
* PBCLOCK = CPU_CLOCK / PBDIV
|
|
*/
|
|
|
|
#define BOARD_PBDIV 1 /* Peripheral clock divisor (PBDIV) */
|
|
#define BOARD_PBCLOCK 40000000 /* Peripheral clock (PBCLK = 40MHz/1) */
|
|
|
|
/* Watchdog pre-scaler (re-visit) */
|
|
|
|
#define BOARD_WD_ENABLE 0 /* Watchdog is disabled */
|
|
#define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* The Mirtoo module has 2 user LEDs labeled LED0 and LED1 in the schematics:
|
|
*
|
|
* --- ----- --------------------------------------------------------------
|
|
* PIN Board Notes
|
|
* --- ----- --------------------------------------------------------------
|
|
* RC8 LED0 Grounded, high value illuminates
|
|
* RC9 LED1 Grounded, high value illuminates
|
|
*
|
|
* The Dimitech DTX1-4000L EV-kit1 supports 3 more LEDs, but there are not
|
|
* controllable from software.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define PIC32MX_MIRTOO_LED0 0
|
|
#define PIC32MX_MIRTOO_LED1 1
|
|
#define PIC32MX_MIRTOO_NLEDS 2
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define PIC32MX_MIRTOO_LED0_BIT (1 << PIC32MX_MIRTOO_LED0)
|
|
#define PIC32MX_MIRTOO_LED1_BIT (1 << PIC32MX_MIRTOO_LED1)
|
|
|
|
/* If CONFIG_ARCH_LEDS is defined, then NuttX will control these LEDs as
|
|
* follows:
|
|
* ON OFF
|
|
* ------------------------- ---- ---- ---- ----
|
|
* LED0 LED1 LED0 LED1
|
|
* ------------------------- ---- ---- ---- ----
|
|
* LED_STARTED 0 OFF OFF --- ---
|
|
* LED_HEAPALLOCATE 1 ON OFF --- ---
|
|
* LED_IRQSENABLED 2 OFF ON --- ---
|
|
* LED_STACKCREATED 3 ON ON --- ---
|
|
* LED_INIRQ 4 ON N/C OFF N/C
|
|
* LED_SIGNAL 4 ON N/C OFF N/C
|
|
* LED_ASSERTION 4 ON N/C OFF N/C
|
|
* LED_PANIC 4 ON N/C OFF N/C
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 1
|
|
#define LED_IRQSENABLED 2
|
|
#define LED_STACKCREATED 3
|
|
#define LED_INIRQ 4
|
|
#define LED_SIGNAL 4
|
|
#define LED_ASSERTION 4
|
|
#define LED_PANIC 4
|
|
|
|
#define LED_NVALUES 5
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Inline Functions
|
|
****************************************************************************/
|
|
|
|
#ifdef __cplusplus
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_MIPS_PIC32MX_MIRTOO_INCLUDE_BOARD_H */
|