98 lines
3.6 KiB
C
98 lines
3.6 KiB
C
/****************************************************************************
|
|
* boards/arm/nrf52/nrf52840-dongle/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_NRF52_NRF52840_DONGLE_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_NRF52_NRF52840_DONGLE_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#include <stdbool.h>
|
|
|
|
#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_NRF52_GPIOTE)
|
|
# include <nuttx/irq.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
#define BOARD_SYSTICK_CLOCK (64000000)
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* A low output illuminates the LED.
|
|
*
|
|
* LED index values for use with board_userled()
|
|
*/
|
|
|
|
#define BOARD_LED1 0
|
|
#define BOARD_NLEDS 1
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
|
|
/* If CONFIG_ARCH_LEDS is defined, the LED will be controlled as follows
|
|
* for NuttX debug functionality (where NC means "No Change").
|
|
*/
|
|
|
|
#define LED_STARTED 0 /* OFF */
|
|
#define LED_HEAPALLOCATE 0 /* OFF */
|
|
#define LED_IRQSENABLED 0 /* OFF */
|
|
#define LED_STACKCREATED 1 /* ON */
|
|
#define LED_INIRQ 2 /* NC */
|
|
#define LED_SIGNAL 2 /* NC */
|
|
#define LED_ASSERTION 2 /* NC */
|
|
#define LED_PANIC 3 /* Flashing */
|
|
|
|
/* If CONFIG_ARCH_LEDS is not defined, then the LEDs are completely under
|
|
* control of the application. The following interfaces are then available
|
|
* for application control of the LEDs:
|
|
*
|
|
* uint32_t board_userled_initialize(void);
|
|
* void board_userled(int led, bool ledon);
|
|
* void board_userled_all(uint32_t ledset);
|
|
*/
|
|
|
|
/* Button definitions *******************************************************/
|
|
|
|
/* Board supports one buttons. */
|
|
|
|
#define BUTTON_BTN1 0
|
|
#define NUM_BUTTONS 1
|
|
|
|
#define BUTTON_BTN1_BIT (1 << BUTTON_BTN1)
|
|
|
|
/* UART Pins ****************************************************************/
|
|
|
|
/* The following definitions must be provided so that the NRF52 serial
|
|
* driver can set up the UART for the serial console properly.
|
|
*/
|
|
|
|
#define BOARD_UART0_RX_PIN (GPIO_INPUT | GPIO_PORT0 | GPIO_PIN(13))
|
|
#define BOARD_UART0_TX_PIN (GPIO_OUTPUT | GPIO_VALUE_ONE | GPIO_PORT0 | GPIO_PIN(15))
|
|
|
|
#endif /* __BOARDS_ARM_NRF52_NRF52840_DONGLE_INCLUDE_BOARD_H */
|