OrgApache/incubator-nuttx
OrgApache
/
incubator-nuttx
mirror of https://github.com/apache/incubator-nuttx.git
1
0
Fork 0
Code Issues Releases Wiki Activity
incubator-nuttx/drivers/lcd/ug-2864ambag01.c

1172 lines
38 KiB
C
Raw Blame History

/****************************************************************************
* drivers/lcd/ug-2864ambag01.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/* Driver for Univision UG-2864AMBAG01 OLED display (with SH1101A controller)
* in SPI mode
*
* References:
* 1. Product Specification (Preliminary),
* Part Name: OEL Display Module, Part ID:
* UG-2864AMBAG01, Doc No: SASI-9015-A, Univision Technology Inc.
* 2. SH1101A, 132 X 64 Dot Matrix OLED/PLED,
* Preliminary Segment/Common Driver with
* Controller, Sino Wealth
*/
/****************************************************************************
* Device memory organization:
*
* +----------------------------+
* | Column |
* --------+----+---+---+---+-...-+-----+
* Page | 0 | 1 | 2 | 3 | ... | 131 |
* --------+----+---+---+---+-...-+-----+
* Page 0 | D0 | X | | | | |
* | D1 | X | | | | |
* | D2 | X | | | | |
* | D3 | X | | | | |
* | D4 | X | | | | |
* | D5 | X | | | | |
* | D6 | X | | | | |
* | D7 | X | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 1 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 2 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 3 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 4 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 5 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 6 | | | | | | |
* --------+----+---+---+---+-...-+-----+
* Page 7 | | | | | | |
* --------+----+---+---+---+-...-+-----+
*
* ----------------------------------+--------------------------------------
* Landscape Display: | Reverse Landscape Display:
* --------+-----------------------+ | -------+---------------------------+
* | Column | | | Column |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 0 | 0 | 1 | 2 | | 131 | | Page 7 | 131 | 130 | 129 | | 0 |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 1 | V | | Page 6 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 2 | V | | Page 5 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 3 | V | | Page 4 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 4 | V | | Page 3 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 5 | V | | Page 2 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 6 | V | | Page 1 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* Page 7 | V | | Page 0 | ^ |
* --------+---+---+---+-...-+-----+ | -------+-----+-----+-----+-...-+---+
* ----------------------------------+--------------------------------------
*
* ----------------------------------+--------------------------------------
* Portrait Display: | Reverse Portrait Display:
* -----------+---------------------+| -----------+---------------------+
* | Page || | Page |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* Column 0 | 0 | 1 | 2 | | 7 || Column 131 | 7 | 6 | 5 | | 0 |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* Column 1 | > > > > > || Column 130 | |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* Column 2 | || Column 129 | |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* ... | || ... | |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* Column 131 | || Column 0 | < < < < < |
* -----------+---+---+---+-...-+---+| -----------+---+---+---+-...-+---+
* ----------------------------------+--------------------------------------
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/arch.h>
#include <nuttx/spi/spi.h>
#include <nuttx/lcd/lcd.h>
#include <nuttx/lcd/ug-2864ambag01.h>
#include <arch/irq.h>
#ifdef CONFIG_LCD_UG2864AMBAG01
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* Limitations of the current configuration that I hope to fix someday */
#if CONFIG_UG2864AMBAG01_NINTERFACES != 1
# warning "This implementation supports only a single OLED device"
# undef CONFIG_UG2864AMBAG01_NINTERFACES
# define CONFIG_UG2864AMBAG01_NINTERFACES 1
#endif
#if defined(CONFIG_LCD_PORTRAIT) || defined(CONFIG_LCD_RPORTRAIT)
# warning "No support yet for portrait modes"
# define CONFIG_LCD_LANDSCAPE 1
# undef CONFIG_LCD_PORTRAIT
# undef CONFIG_LCD_RLANDSCAPE
# undef CONFIG_LCD_RPORTRAIT
#endif
/* SH1101A Commands *********************************************************/
#define SH1101A_SETCOLL(ad) (0x00 | ((ad) & 0x0f)) /* Set Lower Column Address: (00h - 0fh) */
#define SH1101A_SETCOLH(ad) (0x10 | ((ad) & 0x0f)) /* Set Higher Column Address: (10h - 1fh) */
#define SH1101A_STARTLINE(ln) (0x40 | ((ln) & 0x3f)) /* Set Display Start Line: (40h - 7fh) */
#define SH1101A_CONTRAST_MODE (0x81) /* Set Contrast Control Register: (Double Bytes Command) */
# define SH1101A_CONTRAST(c) (c)
#define SH1101A_SEGREMAP(m) (0xa0 | ((m) & 0x01)) /* Set Segment Re-map: (a0h - a1h) */
# define SH1101A_REMAPRIGHT SH1101A_SEGREMAP(0) /* Right rotation */
# define SH1101A_REMAPPLEFT SH1101A_SEGREMAP(1) /* Left rotation */
#define SH1101A_EDISPOFFON(s) (0xa4 | ((s) & 0x01)) /* Set Entire Display OFF/ON: (a4h - a5h) */
# define SH1101A_EDISPOFF SH1101A_EDISPOFFON(0) /* Display off */
# define SH1101A_EDISPON SH1101A_EDISPOFFON(1) /* Display on */
#define SH1101A_NORMREV(s) (0xa6 | ((s) & 0x01)) /* Set Normal/Reverse Display: (a6h -a7h) */
# define SH1101A_NORMAL SH1101A_NORMREV(0) /* Normal display */
# define SH1101A_REVERSE SH1101A_NORMREV(1) /* Reverse display */
#define SH1101A_MRATIO_MODE (0xa8) /* Set Multiplex Ration: (Double Bytes Command) */
# define SH1101A_MRATIO(d) ((d) & 0x3f)
#define SH1101A_DCDC_MODE (0xad) /* Set DC-DC OFF/ON: (Double Bytes Command) */
# define SH1101A_DCDC_OFF (0x8a)
# define SH1101A_DCDC_ON (0x8b)
#define SH1101A_DISPOFFON(s) (0xae | ((s) & 0x01)) /* Display OFF/ON: (aeh - afh) */
# define SH1101A_DISPOFF SH1101A_DISPOFFON(0) /* Display off */
# define SH1101A_DISPON SH1101A_DISPOFFON(1) /* Display on */
#define SH1101A_PAGEADDR(a) (0xb0 | ((a) & 0x0f)) /* Set Page Address: (b0h - b7h) */
#define SH1101A_SCANDIR(d) (0xc0 | ((d) & 0x08)) /* Set Common Output Scan Direction: (c0h - c8h) */
# define SH1101A_SCANFROMCOM0 SH1101A_SCANDIR(0x00) /* Scan from COM[0] to COM[n-1]*/
# define SH1101A_SCANTOCOM0 SH1101A_SCANDIR(0x08) /* Scan from COM[n-1] to COM[0] */
#define SH1101A_DISPOFFS_MODE (0xd3) /* Set Display Offset: (Double Bytes Command) */
# define SH1101A_DISPOFFS(o) ((o) & 0x3f)
#define SH1101A_CLKDIV_SET (0xd5) /* Set Display Clock Divide Ratio/Oscillator Frequency: (Double Bytes Command) */
# define SH1101A_CLKDIV(f,d) ((((f) & 0x0f) << 4) | ((d) & 0x0f))
#define SH1101A_CHRGPER_SET (0xd9) /* Set Dis-charge/Pre-charge Period: (Double Bytes Command) */
# define SH1101A_CHRGPER(d,p) ((((d) & 0x0f) << 4) | ((p) & 0x0f))
#define SH1101A_CMNPAD_CONFIG (0xda) /* Set Common pads hardware configuration: (Double Bytes Command) */
#define SH1101A_CMNPAD(c) ((0x02) | ((c) & 0x10))
#define SH1101A_VCOM_SET (0xdb) /* Set VCOM Deselect Level: (Double Bytes Command) */
# define SH1101A_VCOM(v) (v)
#define SH1101A_RMWSTART (0xe0) /* Read-Modify-Write: (e0h) */
#define SH1101A_NOP (0xe3) /* NOP: (e3h) */
#define SH1101A_END (0xee) /* End: (eeh) */
#define SH1101A_WRDATA(d) (d) /* Write Display Data */
#define SH1101A_STATUS_BUSY (0x80) /* Read Status */
#define SH1101A_STATUS_ONOFF (0x40)
#define SH1101A_RDDATA(d) (d) /* Read Display Data */
/* Color Properties *********************************************************/
/* Display Resolution
*
* The SH1101A display controller can handle a resolution of 132x64.
* The UG-2864AMBAG01 on the base board is 128x64.
*/
#define UG2864AMBAG01_DEV_XRES 128 /* Only 128 of 131 columns used */
#define UG2864AMBAG01_DEV_YRES 64 /* 8 pages each 8 rows */
#define UG2864AMBAG01_DEV_XOFFSET 2 /* Offset to logical column 0 */
#define UG2864AMBAG01_DEV_PAGES 8 /* 8 pages */
#if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE)
# define UG2864AMBAG01_XRES UG2864AMBAG01_DEV_XRES
# define UG2864AMBAG01_YRES UG2864AMBAG01_DEV_YRES
#else
# define UG2864AMBAG01_XRES UG2864AMBAG01_DEV_YRES
# define UG2864AMBAG01_YRES UG2864AMBAG01_DEV_XRES
#endif
/* Color depth and format */
#define UG2864AMBAG01_BPP 1
#define UG2864AMBAG01_COLORFMT FB_FMT_Y1
/* Bytes per logical row and actual device row */
#define UG2864AMBAG01_XSTRIDE (UG2864AMBAG01_XRES >> 3)
#define UG2864AMBAG01_YSTRIDE (UG2864AMBAG01_YRES >> 3)
/* Default contrast */
#define UG2864AMBAG01_CONTRAST (128)
/* The size of the shadow frame buffer or one row buffer.
*
* Frame buffer size: 128 columns x 64 rows / 8 bits-per-pixel
* Row size: 128 columns x 8 rows-per-page / 8 bits-per-pixel
*/
#define UG2864AMBAG01_FBSIZE (UG2864AMBAG01_XSTRIDE * UG2864AMBAG01_YRES)
#define UG2864AMBAG01_ROWSIZE (UG2864AMBAG01_XSTRIDE)
/* Orientation */
#if defined(CONFIG_LCD_LANDSCAPE)
# undef UG2864AMBAG01_DEV_REVERSEX
# undef UG2864AMBAG01_DEV_REVERSEY
#elif defined(CONFIG_LCD_RLANDSCAPE)
# define UG2864AMBAG01_DEV_REVERSEX 1
# define UG2864AMBAG01_DEV_REVERSEY 1
#endif
/* Bit helpers */
#define LS_BIT (1 << 0)
#define MS_BIT (1 << 7)
/****************************************************************************
* Private Type Definition
****************************************************************************/
/* This structure describes the state of this driver */
struct ug2864ambag01_dev_s
{
struct lcd_dev_s dev; /* Publicly visible device structure */
/* Private LCD-specific information follows */
FAR struct spi_dev_s *spi; /* Cached SPI device reference */
uint8_t contrast; /* Current contrast setting */
bool on; /* true: display is on */
/* The SH1101A does not support reading from the display memory in SPI
* mode. Since there is 1 BPP and access is byte-by-byte, it is necessary
* to keep a shadow copy of the framebuffer memory. At 128x64, this amounts
* to 1KB.
*/
uint8_t fb[UG2864AMBAG01_FBSIZE];
};
/****************************************************************************
* Private Function Protototypes
****************************************************************************/
/* Low-level SPI helpers */
static void ug2864ambag01_lock(FAR struct spi_dev_s *spi);
static void ug2864ambag01_unlock(FAR struct spi_dev_s *spi);
/* LCD Data Transfer Methods */
static int ug2864ambag01_putrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR const uint8_t *buffer, size_t npixels);
static int ug2864ambag01_getrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR uint8_t *buffer,
size_t npixels);
/* LCD Configuration */
static int ug2864ambag01_getvideoinfo(FAR struct lcd_dev_s *dev,
FAR struct fb_videoinfo_s *vinfo);
static int ug2864ambag01_getplaneinfo(FAR struct lcd_dev_s *dev,
unsigned int planeno,
FAR struct lcd_planeinfo_s *pinfo);
/* LCD RGB Mapping */
#ifdef CONFIG_FB_CMAP
# error "RGB color mapping not supported by this driver"
#endif
/* Cursor Controls */
#ifdef CONFIG_FB_HWCURSOR
# error "Cursor control not supported by this driver"
#endif
/* LCD Specific Controls */
static int ug2864ambag01_getpower(struct lcd_dev_s *dev);
static int ug2864ambag01_setpower(struct lcd_dev_s *dev, int power);
static int ug2864ambag01_getcontrast(struct lcd_dev_s *dev);
static int ug2864ambag01_setcontrast(struct lcd_dev_s *dev,
unsigned int contrast);
/****************************************************************************
* Private Data
****************************************************************************/
/* This is working memory allocated by the LCD driver for each LCD device
* and for each color plane. This memory will hold one raster line of data.
* The size of the allocated run buffer must therefore be at least
* (bpp * xres / 8). Actual alignment of the buffer must conform to the
* bitwidth of the underlying pixel type.
*
* If there are multiple planes, they may share the same working buffer
* because different planes will not be operate on concurrently. However,
* if there are multiple LCD devices, they must each have unique run buffers.
*/
static uint8_t g_runbuffer[UG2864AMBAG01_ROWSIZE];
/* This structure describes the overall LCD video controller */
static const struct fb_videoinfo_s g_videoinfo =
{
.fmt = UG2864AMBAG01_COLORFMT, /* Color format: RGB16-565: RRRR RGGG GGGB BBBB */
.xres = UG2864AMBAG01_XRES, /* Horizontal resolution in pixel columns */
.yres = UG2864AMBAG01_YRES, /* Vertical resolution in pixel rows */
.nplanes = 1, /* Number of color planes supported */
};
/* This is the standard, NuttX Plane information object */
static const struct lcd_planeinfo_s g_planeinfo =
{
.putrun = ug2864ambag01_putrun, /* Put a run into LCD memory */
.getrun = ug2864ambag01_getrun, /* Get a run from LCD memory */
.buffer = (FAR uint8_t *)g_runbuffer, /* Run scratch buffer */
.bpp = UG2864AMBAG01_BPP, /* Bits-per-pixel */
};
/* This is the OLED driver instance
* (only a single device is supported for now)
*/
static struct ug2864ambag01_dev_s g_oleddev =
{
.dev =
{
/* LCD Configuration */
.getvideoinfo = ug2864ambag01_getvideoinfo,
.getplaneinfo = ug2864ambag01_getplaneinfo,
/* LCD RGB Mapping -- Not supported */
/* Cursor Controls -- Not supported */
/* LCD Specific Controls */
.getpower = ug2864ambag01_getpower,
.setpower = ug2864ambag01_setpower,
.getcontrast = ug2864ambag01_getcontrast,
.setcontrast = ug2864ambag01_setcontrast,
},
};
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: ug2864ambag01_lock
*
* Description:
* Select the SPI, locking and re-configuring if necessary
*
* Input Parameters:
* spi - Reference to the SPI driver structure
*
* Returned Value:
* None
*
* Assumptions:
*
****************************************************************************/
static inline void ug2864ambag01_lock(FAR struct spi_dev_s *spi)
{
/* Lock the SPI bus if there are multiple devices competing for the SPI
* bus.
*/
SPI_LOCK(spi, true);
/* Now make sure that the SPI bus is configured for the UG-2864AMBAG01 (it
* might have gotten configured for a different device while unlocked)
*/
SPI_SETMODE(spi, CONFIG_UG2864AMBAG01_SPIMODE);
SPI_SETBITS(spi, 8);
SPI_HWFEATURES(spi, 0);
SPI_SETFREQUENCY(spi, CONFIG_UG2864AMBAG01_FREQUENCY);
}
/****************************************************************************
* Name: ug2864ambag01_unlock
*
* Description:
* De-select the SPI
*
* Input Parameters:
* spi - Reference to the SPI driver structure
*
* Returned Value:
* None
*
* Assumptions:
*
****************************************************************************/
static inline void ug2864ambag01_unlock(FAR struct spi_dev_s *spi)
{
/* De-select UG-2864AMBAG01 chip and relinquish the SPI bus. */
SPI_LOCK(spi, false);
}
/****************************************************************************
* Name: ug2864ambag01_putrun
*
* Description:
* This method can be used to write a partial raster line to the LCD.
*
* Input Parameters:
* dev - The lcd device
* row - Starting row to write to (range: 0 <= row < yres)
* col - Starting column to write to (range: 0 <= col <= xres-npixels)
* buffer - The buffer containing the run to be written to the LCD
* npixels - The number of pixels to write to the LCD
* (range: 0 < npixels <= xres-col)
*
****************************************************************************/
#if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE)
static int ug2864ambag01_putrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR const uint8_t *buffer, size_t npixels)
{
FAR struct ug2864ambag01_dev_s *priv = (FAR struct ug2864ambag01_dev_s *)
dev;
FAR uint8_t *fbptr;
FAR uint8_t *ptr;
uint8_t devcol;
uint8_t fbmask;
uint8_t page;
uint8_t usrmask;
int pixlen;
uint8_t i;
lcdinfo("row: %d col: %d npixels: %d\n", row, col, npixels);
DEBUGASSERT(buffer);
/* Clip the run to the display */
pixlen = npixels;
if ((unsigned int)col + (unsigned int)pixlen >
(unsigned int)UG2864AMBAG01_XRES)
{
pixlen = (int)UG2864AMBAG01_XRES - (int)col;
}
/* Verify that some portion of the run remains on the display */
if (pixlen <= 0 || row > UG2864AMBAG01_YRES)
{
return OK;
}
/* Perform coordinate conversion for reverse landscape mode.
* If the rows are reversed then rows are are a mirror reflection of
* top to bottom.
*/
#ifdef UG2864AMBAG01_DEV_REVERSEY
row = (UG2864AMBAG01_DEV_YRES - 1) - row;
#endif
/* If the column is switched then the start of the run is the mirror of
* the end of the run.
*
* col+pixlen-1
* col |
* 0 | | XRES
* . S>>>>>>E .
* . E<<<<<<S .
* | |
* | `-(XRES-1)-col
* ` (XRES-1)-col-(pixlen-1)
*/
#ifdef UG2864AMBAG01_DEV_REVERSEX
col = (UG2864AMBAG01_DEV_XRES - 1) - col;
col -= (pixlen - 1);
#endif
/* Get the page number. The range of 64 lines is divided up into eight
* pages of 8 lines each.
*/
page = row >> 3;
/* Update the shadow frame buffer memory. First determine the pixel
* position in the frame buffer memory. Pixels are organized like
* this:
*
* --------+---+---+---+---+-...-+-----+
* Segment | 0 | 1 | 2 | 3 | ... | 131 |
* --------+---+---+---+---+-...-+-----+
* D0 | | X | | | | |
* D1 | | X | | | | |
* D2 | | X | | | | |
* D3 | | X | | | | |
* D4 | | X | | | | |
* D5 | | X | | | | |
* D6 | | X | | | | |
* D7 | | X | | | | |
* --------+---+---+---+---+-...-+-----+
*
* So, in order to draw a white, horizontal line, at row 45. we
* would have to modify all of the bytes in page 45/8 = 5. We
* would have to set bit 45%8 = 5 in every byte in the page.
*/
fbmask = 1 << (row & 7);
fbptr = &priv->fb[page * UG2864AMBAG01_XRES + col];
#ifdef UG2864AMBAG01_DEV_REVERSEX
ptr = fbptr + (pixlen - 1);
#else
ptr = fbptr;
#endif
#ifdef CONFIG_LCD_PACKEDMSFIRST
usrmask = MS_BIT;
#else
usrmask = LS_BIT;
#endif
for (i = 0; i < pixlen; i++)
{
/* Set or clear the corresponding bit */
#ifdef UG2864AMBAG01_DEV_REVERSEX
if ((*buffer & usrmask) != 0)
{
*ptr-- |= fbmask;
}
else
{
*ptr-- &= ~fbmask;
}
#else
if ((*buffer & usrmask) != 0)
{
*ptr++ |= fbmask;
}
else
{
*ptr++ &= ~fbmask;
}
#endif
/* Inc/Decrement to the next source pixel */
#ifdef CONFIG_LCD_PACKEDMSFIRST
if (usrmask == LS_BIT)
{
buffer++;
usrmask = MS_BIT;
}
else
{
usrmask >>= 1;
}
#else
if (usrmask == MS_BIT)
{
buffer++;
usrmask = LS_BIT;
}
else
{
usrmask <<= 1;
}
#endif
}
/* Offset the column position to account for smaller horizontal
* display range.
*/
devcol = col + UG2864AMBAG01_DEV_XOFFSET;
/* Lock and select device */
ug2864ambag01_lock(priv->spi);
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), true);
/* Select command transfer */
SPI_CMDDATA(priv->spi, SPIDEV_DISPLAY(0), true);
/* Set the starting position for the run */
/* Set the column address to the XOFFSET value */
SPI_SEND(priv->spi, SH1101A_SETCOLL(devcol & 0x0f));
SPI_SEND(priv->spi, SH1101A_SETCOLH(devcol >> 4));
/* Set the page address */
SPI_SEND(priv->spi, SH1101A_PAGEADDR(page));
/* Select data transfer */
SPI_CMDDATA(priv->spi, SPIDEV_DISPLAY(0), false);
/* Then transfer all of the data */
SPI_SNDBLOCK(priv->spi, fbptr, pixlen);
/* De-select and unlock the device */
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), false);
ug2864ambag01_unlock(priv->spi);
return OK;
}
#else
# error "Configuration not implemented"
#endif
/****************************************************************************
* Name: ug2864ambag01_getrun
*
* Description:
* This method can be used to read a partial raster line from the LCD.
*
* Description:
* This method can be used to write a partial raster line to the LCD.
*
* dev - The lcd device
* row - Starting row to read from (range: 0 <= row < yres)
* col - Starting column to read read (range: 0 <= col <= xres-npixels)
* buffer - The buffer in which to return the run read from the LCD
* npixels - The number of pixels to read from the LCD
* (range: 0 < npixels <= xres-col)
*
****************************************************************************/
#if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE)
static int ug2864ambag01_getrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR uint8_t *buffer,
size_t npixels)
{
FAR struct ug2864ambag01_dev_s *priv = (FAR struct ug2864ambag01_dev_s *)
dev;
FAR uint8_t *fbptr;
uint8_t page;
uint8_t fbmask;
uint8_t usrmask;
int pixlen;
uint8_t i;
lcdinfo("row: %d col: %d npixels: %d\n", row, col, npixels);
DEBUGASSERT(buffer);
/* Clip the run to the display */
pixlen = npixels;
if ((unsigned int)col + (unsigned int)pixlen >
(unsigned int)UG2864AMBAG01_XRES)
{
pixlen = (int)UG2864AMBAG01_XRES - (int)col;
}
/* Verify that some portion of the run is actually the display */
if (pixlen <= 0 || row > UG2864AMBAG01_YRES)
{
return -EINVAL;
}
/* Perform coordinate conversion for reverse landscape mode.
* If the rows are reversed then rows are are a mirror reflection of
* top to bottom.
*/
#ifdef UG2864AMBAG01_DEV_REVERSEY
row = (UG2864AMBAG01_DEV_YRES - 1) - row;
#endif
/* If the column is switched then the start of the run is the mirror of
* the end of the run.
*
* col+pixlen-1
* col |
* 0 | | XRES
* . S>>>>>>E .
* . E<<<<<<S .
* | |
* | `-(XRES-1)-col
* ` (XRES-1)-col-(pixlen-1)
*/
#ifdef UG2864AMBAG01_DEV_REVERSEX
col = (UG2864AMBAG01_DEV_XRES - 1) - col;
#endif
/* Then transfer the display data from the shadow frame buffer memory */
/* Get the page number. The range of 64 lines is divided up into eight
* pages of 8 lines each.
*/
page = row >> 3;
/* Update the shadow frame buffer memory. First determine the pixel
* position in the frame buffer memory. Pixels are organized like
* this:
*
* --------+---+---+---+---+-...-+-----+
* Segment | 0 | 1 | 2 | 3 | ... | 131 |
* --------+---+---+---+---+-...-+-----+
* D0 | | X | | | | |
* D1 | | X | | | | |
* D2 | | X | | | | |
* D3 | | X | | | | |
* D4 | | X | | | | |
* D5 | | X | | | | |
* D6 | | X | | | | |
* D7 | | X | | | | |
* --------+---+---+---+---+-...-+-----+
*
* So, in order to draw a white, horizontal line, at row 45. we
* would have to modify all of the bytes in page 45/8 = 5. We
* would have to set bit 45%8 = 5 in every byte in the page.
*/
fbmask = 1 << (row & 7);
fbptr = &priv->fb[page * UG2864AMBAG01_XRES + col];
#ifdef CONFIG_LCD_PACKEDMSFIRST
usrmask = MS_BIT;
#else
usrmask = LS_BIT;
#endif
*buffer = 0;
for (i = 0; i < pixlen; i++)
{
/* Set or clear the corresponding bit */
#ifdef UG2864AMBAG01_DEV_REVERSEX
uint8_t byte = *fbptr--;
#else
uint8_t byte = *fbptr++;
#endif
if ((byte & fbmask) != 0)
{
*buffer |= usrmask;
}
/* Inc/Decrement to the next destination pixel. Hmmmm. It looks like
* this logic could write past the end of the user buffer. Revisit
* this!
*/
#ifdef CONFIG_LCD_PACKEDMSFIRST
if (usrmask == LS_BIT)
{
buffer++;
*buffer = 0;
usrmask = MS_BIT;
}
else
{
usrmask >>= 1;
}
#else
if (usrmask == MS_BIT)
{
buffer++;
*buffer = 0;
usrmask = LS_BIT;
}
else
{
usrmask <<= 1;
}
#endif
}
return OK;
}
#else
# error "Configuration not implemented"
#endif
/****************************************************************************
* Name: ug2864ambag01_getvideoinfo
*
* Description:
* Get information about the LCD video controller configuration.
*
****************************************************************************/
static int ug2864ambag01_getvideoinfo(FAR struct lcd_dev_s *dev,
FAR struct fb_videoinfo_s *vinfo)
{
DEBUGASSERT(dev && vinfo);
lcdinfo("fmt: %d xres: %d yres: %d nplanes: %d\n",
g_videoinfo.fmt, g_videoinfo.xres,
g_videoinfo.yres, g_videoinfo.nplanes);
memcpy(vinfo, &g_videoinfo, sizeof(struct fb_videoinfo_s));
return OK;
}
/****************************************************************************
* Name: ug2864ambag01_getplaneinfo
*
* Description:
* Get information about the configuration of each LCD color plane.
*
****************************************************************************/
static int ug2864ambag01_getplaneinfo(FAR struct lcd_dev_s *dev,
unsigned int planeno,
FAR struct lcd_planeinfo_s *pinfo)
{
DEBUGASSERT(pinfo && planeno == 0);
lcdinfo("planeno: %d bpp: %d\n", planeno, g_planeinfo.bpp);
memcpy(pinfo, &g_planeinfo, sizeof(struct lcd_planeinfo_s));
pinfo->dev = dev;
return OK;
}
/****************************************************************************
* Name: ug2864ambag01_getpower
*
* Description:
* Get the LCD panel power status
* (0: full off - CONFIG_LCD_MAXPOWER: full on.)
* On backlit LCDs, this setting may correspond to the backlight setting.
*
****************************************************************************/
static int ug2864ambag01_getpower(FAR struct lcd_dev_s *dev)
{
FAR struct ug2864ambag01_dev_s *priv =
(FAR struct ug2864ambag01_dev_s *)dev;
DEBUGASSERT(priv);
lcdinfo("power: %s\n", priv->on ? "ON" : "OFF");
return priv->on ? CONFIG_LCD_MAXPOWER : 0;
}
/****************************************************************************
* Name: ug2864ambag01_setpower
*
* Description:
* Enable/disable LCD panel power
* (0: full off - CONFIG_LCD_MAXPOWER: full on). On
* backlit LCDs, this setting may correspond to the backlight setting.
*
****************************************************************************/
static int ug2864ambag01_setpower(struct lcd_dev_s *dev, int power)
{
struct ug2864ambag01_dev_s *priv = (struct ug2864ambag01_dev_s *)dev;
DEBUGASSERT(priv && (unsigned)power <= CONFIG_LCD_MAXPOWER && priv->spi);
lcdinfo("power: %d [%d]\n", power, priv->on ? CONFIG_LCD_MAXPOWER : 0);
/* Lock and select device */
ug2864ambag01_lock(priv->spi);
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), true);
if (power <= 0)
{
/* Turn the display off */
SPI_SEND(priv->spi, SH1101A_DISPOFF);
priv->on = false;
}
else
{
/* Turn the display on */
SPI_SEND(priv->spi, SH1101A_DISPON);
priv->on = true;
}
/* De-select and unlock the device */
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), false);
ug2864ambag01_unlock(priv->spi);
return OK;
}
/****************************************************************************
* Name: ug2864ambag01_getcontrast
*
* Description:
* Get the current contrast setting (0-CONFIG_LCD_MAXCONTRAST).
*
****************************************************************************/
static int ug2864ambag01_getcontrast(struct lcd_dev_s *dev)
{
struct ug2864ambag01_dev_s *priv = (struct ug2864ambag01_dev_s *)dev;
DEBUGASSERT(priv);
lcdinfo("contrast: %d\n", priv->contrast);
return priv->contrast;
}
/****************************************************************************
* Name: ug2864ambag01_setcontrast
*
* Description:
* Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
*
****************************************************************************/
static int ug2864ambag01_setcontrast(struct lcd_dev_s *dev,
unsigned int contrast)
{
struct ug2864ambag01_dev_s *priv = (struct ug2864ambag01_dev_s *)dev;
unsigned int scaled;
lcdinfo("contrast: %d\n", contrast);
DEBUGASSERT(priv);
/* Verify the contrast value */
#ifdef CONFIG_DEBUG_FEATURES
if (contrast > CONFIG_LCD_MAXCONTRAST)
{
return -EINVAL;
}
#endif
/* Scale contrast: newcontrast = 255 * contrast / CONFIG_LCD_MAXCONTRAST
* Where contrast is in the range {1,255}
*/
#if CONFIG_LCD_MAXCONTRAST != 255
scaled = ((contrast << 8) - 1) / CONFIG_LCD_MAXCONTRAST;
#else
scaled = contrast;
#endif
/* Lock and select device */
ug2864ambag01_lock(priv->spi);
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), true);
/* Select command transfer */
SPI_CMDDATA(priv->spi, SPIDEV_DISPLAY(0), true);
/* Set the contrast */
SPI_SEND(priv->spi, SH1101A_CONTRAST_MODE); /* Set contrast control register */
SPI_SEND(priv->spi, SH1101A_CONTRAST(scaled)); /* Data 1: Set 1 of 256 contrast steps */
priv->contrast = contrast;
/* De-select and unlock the device */
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), false);
ug2864ambag01_unlock(priv->spi);
return OK;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: ug2864ambag01_initialize
*
* Description:
* Initialize the UG-2864AMBAG01 video hardware. The initial state of the
* OLED is fully initialized, display memory cleared, and the OLED ready
* to use, but with the power setting at 0 (full off == sleep mode).
*
* Input Parameters:
*
* spi - A reference to the SPI driver instance.
* devno - A value in the range of 0 through
* CONFIG_UG2864AMBAG01_NINTERFACES-1.
* This allows support for multiple OLED devices.
*
* Returned Value:
*
* On success, this function returns a reference to the LCD object for
* the specified OLED. NULL is returned on any failure.
*
****************************************************************************/
FAR struct lcd_dev_s *ug2864ambag01_initialize(FAR struct spi_dev_s *spi,
unsigned int devno)
{
FAR struct ug2864ambag01_dev_s *priv = &g_oleddev;
lcdinfo("Initializing\n");
DEBUGASSERT(spi && devno == 0);
/* Save the reference to the SPI device */
priv->spi = spi;
/* Lock and select device */
ug2864ambag01_lock(priv->spi);
SPI_SELECT(spi, SPIDEV_DISPLAY(0), true);
/* Select command transfer */
SPI_CMDDATA(spi, SPIDEV_DISPLAY(0), true);
/* Configure the device */
SPI_SEND(spi, SH1101A_DISPOFF); /* Display off */
SPI_SEND(spi, SH1101A_SETCOLL(0)); /* Set lower column address */
SPI_SEND(spi, SH1101A_SETCOLH(0)); /* Set higher column address */
SPI_SEND(spi, SH1101A_STARTLINE(0)); /* Set display start line */
SPI_SEND(spi, SH1101A_PAGEADDR(0)); /* Set page address */
SPI_SEND(spi, SH1101A_CONTRAST_MODE); /* Contrast control */
SPI_SEND(spi, UG2864AMBAG01_CONTRAST); /* Default contrast */
SPI_SEND(spi, SH1101A_REMAPPLEFT); /* Set segment remap left */
SPI_SEND(spi, SH1101A_EDISPOFF); /* Normal display */
SPI_SEND(spi, SH1101A_NORMAL); /* Normal (un-reversed) display mode */
SPI_SEND(spi, SH1101A_MRATIO_MODE); /* Multiplex ratio */
SPI_SEND(spi, SH1101A_MRATIO(0x3f)); /* Duty = 1/64 */
SPI_SEND(spi, SH1101A_SCANTOCOM0); /* Com scan direction: Scan from COM[n-1] to COM[0] */
SPI_SEND(spi, SH1101A_DISPOFFS_MODE); /* Set display offset */
SPI_SEND(spi, SH1101A_DISPOFFS(0));
SPI_SEND(spi, SH1101A_CLKDIV_SET); /* Set clock divider */
SPI_SEND(spi, SH1101A_CLKDIV(0, 0));
SPI_SEND(spi, SH1101A_CMNPAD_CONFIG); /* Set common pads */
SPI_SEND(spi, SH1101A_CMNPAD(0x10));
SPI_SEND(spi, SH1101A_VCOM_SET);
SPI_SEND(spi, SH1101A_VCOM(0x40));
SPI_SEND(spi, SH1101A_DCDC_MODE); /* DC/DC control mode: on */
SPI_SEND(spi, SH1101A_DCDC_ON);
SPI_SEND(spi, SH1101A_DISPON); /* display ON */
/* De-select and unlock the device */
SPI_SELECT(spi, SPIDEV_DISPLAY(0), false);
ug2864ambag01_unlock(priv->spi);
/* Clear the display */
up_mdelay(100);
ug2864ambag01_fill(&priv->dev, UG_Y1_BLACK);
return &priv->dev;
}
/****************************************************************************
* Name: ug2864ambag01_fill
*
* Description:
* This non-standard method can be used to clear the entire display by
* writing one color to the display.
* This is much faster than writing a series of runs.
*
* Input Parameters:
* priv - Reference to private driver structure
*
* Assumptions:
* Caller has selected the OLED section.
*
****************************************************************************/
void ug2864ambag01_fill(FAR struct lcd_dev_s *dev, uint8_t color)
{
FAR struct ug2864ambag01_dev_s *priv = &g_oleddev;
unsigned int page;
/* Make an 8-bit version of the selected color */
if (color & 1)
{
color = 0xff;
}
else
{
color = 0;
}
/* Initialize the framebuffer */
memset(priv->fb, color, UG2864AMBAG01_FBSIZE);
/* Lock and select device */
ug2864ambag01_lock(priv->spi);
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), true);
/* Visit each page */
for (page = 0; page < UG2864AMBAG01_DEV_PAGES; page++)
{
/* Select command transfer */
SPI_CMDDATA(priv->spi, SPIDEV_DISPLAY(0), true);
/* Set the column address to the XOFFSET value */
SPI_SEND(priv->spi, SH1101A_SETCOLL(UG2864AMBAG01_DEV_XOFFSET));
SPI_SEND(priv->spi, SH1101A_SETCOLH(0));
/* Set the page address */
SPI_SEND(priv->spi, SH1101A_PAGEADDR(page));
/* Select data transfer */
SPI_CMDDATA(priv->spi, SPIDEV_DISPLAY(0), false);
/* Transfer one page of the selected color */
SPI_SNDBLOCK(priv->spi, &priv->fb[page * UG2864AMBAG01_XRES],
UG2864AMBAG01_XRES);
}
/* De-select and unlock the device */
SPI_SELECT(priv->spi, SPIDEV_DISPLAY(0), false);
ug2864ambag01_unlock(priv->spi);
}
#endif /* CONFIG_LCD_UG2864AMBAG01 */
Reference in New Issue View Git Blame Copy Permalink