incubator-nuttx/drivers/input/ads7843e.h

172 lines
6.4 KiB
C

/****************************************************************************
* drivers/input/ads7843e.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/* References:
* "Touch Screen Controller, ADS7843," Burr-Brown Products from Texas
* Instruments, SBAS090B, September 2000, Revised May 2002"
*
* See also:
* "Low Voltage I/O Touch Screen Controller, TSC2046," Burr-Brown Products
* from Texas Instruments, SBAS265F, October 2002, Revised August 2007."
*
* "XPT2046 Data Sheet," Shenzhen XPTek Technology Co., Ltd, 2007
*/
#ifndef __DRIVERS_INPUT_ADS7843E_H
#define __DRIVERS_INPUT_ADS7843E_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdint.h>
#include <poll.h>
#include <nuttx/wqueue.h>
#include <nuttx/wdog.h>
#include <nuttx/clock.h>
#include <nuttx/semaphore.h>
#include <nuttx/spi/spi.h>
#include <nuttx/input/ads7843e.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* Reference counting is partially implemented, but not needed in the current
* design.
*/
#undef CONFIG_ADS7843E_REFCNT
/* ADS7843E Interfaces ******************************************************/
/* ADS7843E command bit settings */
#define ADS7843E_CMD_PD0 (1 << 0) /* Bit 0: Power down mode select bit 0 */
#define ADS7843E_CMD_PD1 (1 << 1) /* Bit 1: Power down mode select bit 1 */
#define ADS7843E_CMD_SER (1 << 2) /* Bit 2: SER/DFR\: 0:DFR 1:SER */
#define ADS7843E_CMD_MODE8 (1 << 3) /* Bit 3: Mode 1:8-bits 0:12-bits */
#define ADS7843E_CMD_CHAN_SHIFT (4) /* Bits 4-6: Channel select bits */
#define ADS7843E_CMD_CHAN_MASK (7 << ADS7843E_CMD_CHAN_SHIFT)
#define ADS7843E_CMD_START (1 << 7) /* Bit 7: Start Bit */
/* ADS7843E Commands */
#define ADS7843_CMD_YPOSITION \
((1 << ADS7843E_CMD_CHAN_SHIFT)| ADS7843E_CMD_START | ADS7843E_CMD_PD0 | ADS7843E_CMD_PD1)
#define ADS7843_CMD_XPOSITION \
((5 << ADS7843E_CMD_CHAN_SHIFT)| ADS7843E_CMD_START | ADS7843E_CMD_PD0 | ADS7843E_CMD_PD1)
#define ADS7843_CMD_ENABPENIRQ \
((1 << ADS7843E_CMD_CHAN_SHIFT)| ADS7843E_CMD_START)
/* Driver support ***********************************************************/
/* This format is used to construct the /dev/input[n] device driver path. It
* defined here so that it will be used consistently in all places.
*/
#define DEV_FORMAT "/dev/input%d"
#define DEV_NAMELEN 16
/* Poll the pen position while the pen is down at this rate (50MS): */
#define ADS7843E_WDOG_DELAY MSEC2TICK(50)
/****************************************************************************
* Public Types
****************************************************************************/
/* This describes the state of one contact */
enum ads7843e_contact_e
{
CONTACT_NONE = 0, /* No contact */
CONTACT_DOWN, /* First contact */
CONTACT_MOVE, /* Same contact, possibly different position */
CONTACT_UP, /* Contact lost */
};
/* This structure describes the results of one ADS7843E sample */
struct ads7843e_sample_s
{
uint8_t id; /* Sampled touch point ID */
uint8_t contact; /* Contact state (see enum ads7843e_contact_e) */
bool valid; /* True: x,y contain valid, sampled data */
uint16_t x; /* Measured X position */
uint16_t y; /* Measured Y position */
};
/* This structure describes the state of one ADS7843E driver instance */
struct ads7843e_dev_s
{
#ifdef CONFIG_ADS7843E_MULTIPLE
FAR struct ads7843e_dev_s *flink; /* Supports a singly linked list of drivers */
#endif
#ifdef CONFIG_ADS7843E_REFCNT
uint8_t crefs; /* Number of times the device has been opened */
#endif
uint8_t nwaiters; /* Number of threads waiting for ADS7843E data */
uint8_t id; /* Current touch point ID */
volatile bool penchange; /* An unreported event is buffered */
uint16_t threshx; /* Thresholding X value */
uint16_t threshy; /* Thresholding Y value */
sem_t devsem; /* Manages exclusive access to this structure */
sem_t waitsem; /* Used to wait for the availability of data */
FAR struct ads7843e_config_s *config; /* Board configuration data */
FAR struct spi_dev_s *spi; /* Saved SPI driver instance */
struct work_s work; /* Supports the interrupt handling "bottom half" */
struct ads7843e_sample_s sample; /* Last sampled touch point data */
struct wdog_s wdog; /* Poll the position while the pen is down */
/* The following is a list if poll structures of threads waiting for
* driver events. The 'struct pollfd' reference for each open is also
* retained in the f_priv field of the 'struct file'.
*/
struct pollfd *fds[CONFIG_ADS7843E_NPOLLWAITERS];
};
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
#ifdef __cplusplus
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
#undef EXTERN
#ifdef __cplusplus
}
#endif
#endif /* __DRIVERS_INPUT_ADS7843E_H */