111 lines
4.1 KiB
Plaintext
111 lines
4.1 KiB
Plaintext
boards/renesas/m16c/skp16c26/README.txt
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
1. The buildroot package can be used to build an M16C toolchain. The toolchain
|
|
buildroot can be downloaded from buildroot in the NuttX GIT. Insructions
|
|
for building the toolchain are provided below.
|
|
|
|
However, the target cannot be built because the GNU m16c-nuttx-elf-ld link fails with
|
|
the following message:
|
|
|
|
m32c-nuttx-elf-ld: BFD (GNU Binutils) 2.19 assertion fail /home/Owner/projects/nuttx/buildroot/toolchain_build_m32c/binutils-2.19/bfd/elf32-m32c.c:482
|
|
|
|
Where the reference line is:
|
|
|
|
/* If the symbol is out of range for a 16-bit address,
|
|
we must have allocated a plt entry. */
|
|
BFD_ASSERT (*plt_offset != (bfd_vma) -1);
|
|
|
|
No workaround is known at this time. This is a show stopper for M16C.
|
|
|
|
2. A supported version of the M16C toolchain is available here:
|
|
|
|
http://www.kpitgnutools.com/index.php
|
|
|
|
This download is free but requires registration. Unfortunately, this v0901 of
|
|
this toolchain shows the same behavior:
|
|
|
|
c:\Hew3\Tools\KPIT Cummins\GNUM16CM32C-ELF\v0901\m32c-elf\bin\m32c-elf-ld.exe: BFD (GNU Binutils) 2.19-GNUM16CM32C_v0901 assertion fail /home/kpit/fsfsrc/binutils-2.19/bfd/elf32-m32c.c:482
|
|
|
|
It is possible that this error message may be telling me -- a very roundabout way --
|
|
that I have exceeded the FLASH region, but I think that unlikely (it is difficult
|
|
to know if the link does not complete gracefully).
|
|
|
|
BUILDING THE R8C/M16C/M32C GNU TOOLCHAIN USING BUILDROOT
|
|
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
|
|
|
NOTE: See the toolchain issues above -- you may not want to waste your time.
|
|
|
|
1. CD to the correct directory.
|
|
|
|
Change to the directory just above the NuttX installation. If <nuttx-dir> is
|
|
where NuttX is installed, then cd to <nuttx-dir>/..
|
|
|
|
2. Get and Install the buildroot Module
|
|
|
|
a. Using a release tarball:
|
|
|
|
cd <nuttx-dir>/..
|
|
Download the appropriate buildroot package.
|
|
unpack the buildroot package
|
|
rename the directory to buildroot
|
|
|
|
b. Using GIT
|
|
|
|
Check out the buildroot module. GIT checkout instructions:
|
|
|
|
git clone hhttps://patacongo@bitbucket.org/nuttx/buildroot.git buildroot
|
|
|
|
Make the archive directory:
|
|
|
|
mkdir archive
|
|
|
|
The <nuttx-dir>/../buildroot is where the toolchain is built;
|
|
The <nuttx-dir>/../archive directory is where toolchain sources will be downloaded.
|
|
|
|
3. Make sure that NuttX is configured
|
|
|
|
cd <nuttx-dir>
|
|
tools/configure.sh <nuttx-configuration>
|
|
|
|
4. Configure and Make the buildroot
|
|
|
|
cd <buildroot-dir>
|
|
cp boards/m32c-defconfig-4.2.4 .config
|
|
make oldconfig
|
|
make
|
|
|
|
This will download the large source packages for the toolchain and build the toolchain.
|
|
The resulting binaries will be under buildroot/build_m32c. There will also be a
|
|
large build directory called toolchain_build_m32c; this directory can be removed once
|
|
the build completes successfully.
|
|
|
|
Cygwin GCC BUILD NOTES
|
|
^^^^^^^^^^^^^^^^^^^^^^
|
|
On Cygwin, the buildroot 'make' command will fail with an error like:
|
|
|
|
"...
|
|
build/genchecksum cc1-dummy > cc1-checksum.c
|
|
opening cc1-dummy: No such file or directory
|
|
..."
|
|
|
|
This is caused because on Cygwin, host executables will be generated with the extension .exe
|
|
and, apparently, the make variable "exeext" is set incorrectly. A work around after the
|
|
above occurs is:
|
|
|
|
cd toolchain_build_m32c/gcc-4.2.4-initial/gcc # Go to the directory where error occurred
|
|
mv cc1-dummy.exe cc1-dummy # Rename the executable without .exe
|
|
rm cc1-checksum.c # Get rid of the bad generated file
|
|
|
|
Then resume the buildroot make:
|
|
|
|
cd - # Back to the buildroot make directory
|
|
make # Restart the build
|
|
|
|
GCC is built twice. First a initial, "bootstrap" GCC is produced in
|
|
toolchain_build_m32c/gcc-4.2.4-initial, then the final GCC is produced in
|
|
toolchain_build_m32c/gcc-4.2.4-final. The above error will occur twice: Once for
|
|
the initial GCC build (see above) and once for the final GCC build. For the final GCC
|
|
build, the workaround is the same except that the directory will be
|
|
toolchain_build_m32c/gcc-4.2.4-final/gcc.
|