126 lines
4.9 KiB
C
126 lines
4.9 KiB
C
/****************************************************************************
|
|
* include/nuttx/net/encx24j600.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __INCLUDE_NUTTX_NET_ENCX24J600_H
|
|
#define __INCLUDE_NUTTX_NET_ENCX24J600_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <stdint.h>
|
|
#include <stdbool.h>
|
|
|
|
#include <nuttx/irq.h>
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* ENCX24J600 Configuration Settings:
|
|
*
|
|
* CONFIG_ENCX24J600 - Enabled ENCX24J600 support
|
|
* CONFIG_ENCX24J600_SPIMODE - Controls the SPI mode
|
|
* CONFIG_ENCX24J600_FREQUENCY - Define to use a different bus frequency
|
|
* CONFIG_ENCX24J600_NINTERFACES - Specifies the number of physical
|
|
* ENCX24J600 devices that will be supported.
|
|
* CONFIG_ENCX24J600_HALFDUPPLEX - Default is full duplex
|
|
*/
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
/* The ENCX24J600 normal provides interrupts to the MCU via a GPIO pin. The
|
|
* following structure provides an MCU-independent mechanixm for controlling
|
|
* the ENCX24J600 GPIO interrupt.
|
|
*
|
|
* The ENC32J60 interrupt is an active low, *level* interrupt. "When an
|
|
* interrupt occurs, the interrupt flag is set. If the interrupt is enabled
|
|
* in the EIE register and the INTIE global interrupt enable bit is set, the
|
|
* INT pin will be driven low"
|
|
*
|
|
* "When an enabled interrupt occurs, the interrupt pin will remain low until
|
|
* all flags which are causing the interrupt are cleared or masked off
|
|
* (enable bit is cleared) by the host controller." However, the interrupt
|
|
* will behave like a falling edge interrupt because "After an interrupt
|
|
* occurs, the host controller [clears] the global enable bit for the
|
|
* interrupt pin before servicing the interrupt. Clearing the enable bit
|
|
* will cause the interrupt pin to return to the non-asserted state (high).
|
|
* Doing so will prevent the host controller from missing a falling edge
|
|
* should another interrupt occur while the immediate interrupt is being
|
|
* serviced."
|
|
*/
|
|
|
|
struct enc_lower_s
|
|
{
|
|
int (*attach)(FAR const struct enc_lower_s *lower, xcpt_t handler,
|
|
FAR void *arg);
|
|
void (*enable)(FAR const struct enc_lower_s *lower);
|
|
void (*disable)(FAR const struct enc_lower_s *lower);
|
|
};
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifdef __cplusplus
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: enc_initialize
|
|
*
|
|
* Description:
|
|
* Initialize the Ethernet driver. The ENCX24J600 device is assumed to be
|
|
* in the post-reset state upon entry to this function.
|
|
*
|
|
* Input Parameters:
|
|
* spi - A reference to the platform's SPI driver for the ENCX24J600
|
|
* lower - The MCU-specific interrupt used to control low-level MCU
|
|
* functions (i.e., ENCX24J600 GPIO interrupts).
|
|
* devno - If more than one ENCX24J600 is supported, then this is the
|
|
* zero based number that identifies the ENCX24J600;
|
|
*
|
|
* Returned Value:
|
|
* OK on success; Negated errno on failure.
|
|
*
|
|
* Assumptions:
|
|
*
|
|
****************************************************************************/
|
|
|
|
struct spi_dev_s; /* see nuttx/spi/spi.h */
|
|
int enc_initialize(FAR struct spi_dev_s *spi,
|
|
FAR const struct enc_lower_s *lower, unsigned int devno);
|
|
#undef EXTERN
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* __INCLUDE_NUTTX_NET_ENCX24J600_H */
|