151 lines
3.5 KiB
Plaintext
151 lines
3.5 KiB
Plaintext
#
|
|
# For a description of the syntax of this configuration file,
|
|
# see the file kconfig-language.txt in the NuttX tools repository.
|
|
#
|
|
|
|
# MMC/SD-related platform capabilities
|
|
|
|
config ARCH_HAVE_SDIO
|
|
bool
|
|
default n
|
|
|
|
config ARCH_HAVE_SDIOWAIT_WRCOMPLETE
|
|
bool
|
|
default n
|
|
|
|
config ARCH_HAVE_SDIO_PREFLIGHT
|
|
bool
|
|
default n
|
|
|
|
config ARCH_HAVE_SDIO_DELAYED_INVLDT
|
|
bool
|
|
default n
|
|
|
|
menuconfig MMCSD
|
|
bool "MMC/SD Driver Support"
|
|
default n
|
|
---help---
|
|
Support for MMC/SD block drivers. MMC/SD block drivers based on
|
|
SPI and SDIO/MCI interfaces are supported. See include/nuttx/mmcsd.h
|
|
and include/nuttx/sdio.h for further information.
|
|
|
|
if MMCSD
|
|
|
|
config MMCSD_NSLOTS
|
|
int "Number of MMC/SD slots"
|
|
default 1
|
|
---help---
|
|
Number of MMC/SD slots supported by the
|
|
driver. Default is one.
|
|
|
|
config MMCSD_READONLY
|
|
bool "Disable MMC/SD write access"
|
|
default n
|
|
---help---
|
|
Provide read-only access. Default is
|
|
Read/Write
|
|
|
|
config MMCSD_MULTIBLOCK_DISABLE
|
|
bool "Disable MMC/SD multiblock transfer"
|
|
default n
|
|
---help---
|
|
Use only the single block transfer method.
|
|
This setting is used to work around buggy SDIO drivers that cannot handle
|
|
multiple block transfers.
|
|
|
|
config MMCSD_MMCSUPPORT
|
|
bool "MMC cards support"
|
|
default y
|
|
---help---
|
|
Enable support for MMC cards
|
|
|
|
config MMCSD_HAVE_CARDDETECT
|
|
bool "MMC/SD card detect pin"
|
|
default y
|
|
---help---
|
|
SDIO driver card present detection is supported.
|
|
|
|
config MMCSD_HAVE_WRITEPROTECT
|
|
bool "MMC/SD write protect pin"
|
|
default y
|
|
---help---
|
|
SDIO driver write protection detection is supported.
|
|
|
|
config MMCSD_SPI
|
|
bool "MMC/SD SPI transfer support"
|
|
default y
|
|
depends on SPI
|
|
|
|
if MMCSD_SPI
|
|
|
|
config MMCSD_SPICLOCK
|
|
int "MMC/SD maximum SPI clock"
|
|
default 20000000
|
|
depends on MMCSD_SPI
|
|
---help---
|
|
Maximum SPI clock to drive MMC/SD card.
|
|
Default is 20MHz.
|
|
|
|
config MMCSD_SPIMODE
|
|
int "MMC/SD SPI mode"
|
|
default 0
|
|
---help---
|
|
Should be mode 0. However, sometimes this is useful for experimenting.
|
|
|
|
endif
|
|
|
|
config SDIO_DMA
|
|
bool
|
|
default n
|
|
|
|
config MMCSD_SDIO
|
|
bool "MMC/SD SDIO transfer support"
|
|
default n
|
|
depends on ARCH_HAVE_SDIO
|
|
|
|
if MMCSD_SDIO
|
|
|
|
config SDIO_MUXBUS
|
|
bool "SDIO bus share support"
|
|
default n
|
|
---help---
|
|
Set this SDIO interface if the SDIO interface
|
|
or hardware resources are shared with other drivers.
|
|
|
|
config MMCSD_SDIOWAIT_WRCOMPLETE
|
|
bool "Use D0 Busy to detect Write Complete"
|
|
default n
|
|
depends on ARCH_HAVE_SDIOWAIT_WRCOMPLETE
|
|
---help---
|
|
SDIO driver will use D0 Busy signalling to detect Write Complete.
|
|
This option when selected, will enable the MMCSD driver to use the
|
|
underlying SDIO drivers implementation of the SD specification's
|
|
D0 Busy signalling to detect Write Complete. This will avoid
|
|
potentially very long (600Ms+) busy waiting in the MMCSD driver.
|
|
|
|
To implement D0 Busy signalling, the underlying driver must
|
|
be capable of switching the D0 GPIO to be a rising edge sensitive
|
|
interrupt pin. It must then, condition that pin to detect the rising edge
|
|
on receipt of SDWAIT_WRCOMPLETE in the SDIO_WAITENABLE call and
|
|
return it back to regular SDIO mode, when either the ISR fires or pin is
|
|
found to be high in the SDIO_EVENTWAIT call.
|
|
|
|
config SDIO_WIDTH_D1_ONLY
|
|
bool "SDIO 1-bit transfer"
|
|
default n
|
|
---help---
|
|
Select 1-bit transfer mode. Default:
|
|
4-bit transfer mode.
|
|
|
|
config SDIO_BLOCKSETUP
|
|
bool "SDIO block setup"
|
|
default n
|
|
---help---
|
|
Some hardware needs to be informed of the selected blocksize and the
|
|
number of blocks. Others just work on the byte stream. This option
|
|
enables the block setup method in the SDIO vtable.
|
|
|
|
endif
|
|
|
|
endif # MMCSD
|