310 lines
9.1 KiB
ReStructuredText
310 lines
9.1 KiB
ReStructuredText
==================
|
|
ESP32-C6-DevKitC-1
|
|
==================
|
|
|
|
ESP32-C6-DevKitC-1 is an entry-level development board based on ESP32-C6-WROOM-1(U),
|
|
a general-purpose module with a 8 MB SPI flash. This board integrates complete Wi-Fi,
|
|
Bluetooth LE, Zigbee, and Thread functions. You can find the board schematic
|
|
`here <https://espressif-docs.readthedocs-hosted.com/projects/esp-dev-kits/en/latest/_static/esp32-c6-devkitc-1/schematics/esp32-c6-devkitc-1-schematics_v1.2.pdf>`_.
|
|
|
|
Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing.
|
|
Developers can either connect peripherals with jumper wires or mount ESP32-C6-DevKitC-1 on
|
|
a breadboard.
|
|
|
|
.. figure:: esp32-c6-devkitc-1-isometric_v1.2.png
|
|
:alt: ESP32-C6-DevKitC-1 Board Layout
|
|
:figclass: align-center
|
|
|
|
ESP32-C6-DevKitC-1 Board Layout
|
|
|
|
The block diagram below presents main components of the ESP32-C6-DevKitC-1.
|
|
|
|
.. figure:: esp32-c6-devkitc-1-v1.2-block-diagram.png
|
|
:alt: ESP32-C6-DevKitC-1 Electrical Block Diagram
|
|
:figclass: align-center
|
|
|
|
ESP32-C6-DevKitC-1 Electrical Block Diagram
|
|
|
|
Hardware Components
|
|
-------------------
|
|
|
|
.. figure:: esp32-c6-devkitc-1-v1.2-annotated-photo.png
|
|
:alt: ESP32-C6-DevKitC-1 Hardware Components
|
|
:figclass: align-center
|
|
|
|
ESP32-C6-DevKitC-1 Hardware Components
|
|
|
|
Buttons and LEDs
|
|
================
|
|
|
|
Board Buttons
|
|
--------------
|
|
There are two buttons labeled Boot and RST. The RST button is not available
|
|
to software. It pulls the chip enable line that doubles as a reset line.
|
|
|
|
The BOOT button is connected to IO9. On reset it is used as a strapping
|
|
pin to determine whether the chip boots normally or into the serial
|
|
bootloader. After reset, however, the BOOT button can be used for software
|
|
input.
|
|
|
|
Board LEDs
|
|
----------
|
|
|
|
There is one on-board LED that indicates the presence of power.
|
|
Another WS2812 LED is connected to GPIO8 and is available for software.
|
|
|
|
Current Measurement
|
|
===================
|
|
|
|
The J5 headers on the ESP32-C6-DevKitC-1 can be used for measuring the current
|
|
drawn by the ESP32-C6-WROOM-1(U) module:
|
|
|
|
- Remove the jumper: Power supply between the module and peripherals on the
|
|
board is cut off. To measure the module's current, connect the board with an
|
|
ammeter via J5 headers;
|
|
- Apply the jumper (factory default): Restore the board's normal functionality.
|
|
|
|
.. note::
|
|
When using 3V3 and GND pin headers to power the board, please remove the J5 jumper,
|
|
and connect an ammeter in series to the external circuit to measure the module's current.
|
|
|
|
Pin Mapping
|
|
===========
|
|
|
|
.. figure:: esp32-c6-devkitc-1-pin-layout.png
|
|
:alt: ESP32-C6-DevKitC pin layout
|
|
:figclass: align-center
|
|
|
|
ESP32-C6-DevKitC-1 Pin Layout
|
|
|
|
Configurations
|
|
==============
|
|
|
|
All of the configurations presented below can be tested by running the following commands::
|
|
|
|
$ ./tools/configure.sh esp32c6-devkitc:<config_name>
|
|
$ make flash ESPTOOL_PORT=/dev/ttyUSB0 -j
|
|
|
|
Where <config_name> is the name of board configuration you want to use, i.e.: nsh, buttons, wifi...
|
|
Then use a serial console terminal like ``picocom`` configured to 115200 8N1.
|
|
|
|
coremark
|
|
--------
|
|
|
|
This configuration sets the CoreMark benchmark up for running on the maximum
|
|
number of cores for this system. It also enables some optimization flags and
|
|
disables the NuttShell to get the best possible score.
|
|
|
|
.. note:: As the NSH is disabled, the application will start as soon as the
|
|
system is turned on.
|
|
|
|
gpio
|
|
----
|
|
|
|
This is a test for the GPIO driver. It uses GPIO1 and GPIO2 as outputs and
|
|
GPIO9 as an interrupt pin.
|
|
|
|
At the nsh, we can turn the outputs on and off with the following::
|
|
|
|
nsh> gpio -o 1 /dev/gpio0
|
|
nsh> gpio -o 1 /dev/gpio1
|
|
|
|
nsh> gpio -o 0 /dev/gpio0
|
|
nsh> gpio -o 0 /dev/gpio1
|
|
|
|
We can use the interrupt pin to send a signal when the interrupt fires::
|
|
|
|
nsh> gpio -w 14 /dev/gpio2
|
|
|
|
The pin is configured as a rising edge interrupt, so after issuing the
|
|
above command, connect it to 3.3V.
|
|
|
|
nsh
|
|
---
|
|
|
|
Basic configuration to run the NuttShell (nsh).
|
|
|
|
ostest
|
|
------
|
|
|
|
This is the NuttX test at ``apps/testing/ostest`` that is run against all new
|
|
architecture ports to assure a correct implementation of the OS.
|
|
|
|
pwm
|
|
---
|
|
|
|
This configuration demonstrates the use of PWM through a LED connected to GPIO8.
|
|
To test it, just execute the ``pwm`` application::
|
|
|
|
nsh> pwm
|
|
pwm_main: starting output with frequency: 10000 duty: 00008000
|
|
pwm_main: stopping output
|
|
|
|
rmt
|
|
---
|
|
|
|
This configuration configures the transmitter and the receiver of the
|
|
Remote Control Transceiver (RMT) peripheral on the ESP32-C6 using GPIOs 8
|
|
and 2, respectively. The RMT peripheral is better explained
|
|
`here <https://docs.espressif.com/projects/esp-idf/en/latest/esp32c6/api-reference/peripherals/rmt.html>`__,
|
|
in the ESP-IDF documentation. The minimal data unit in the frame is called the
|
|
RMT symbol, which is represented by ``rmt_item32_t`` in the driver:
|
|
|
|
.. figure:: rmt_symbol.png
|
|
:align: center
|
|
|
|
The example ``rmtchar`` can be used to test the RMT peripheral. Connecting
|
|
these pins externally to each other will make the transmitter send RMT items
|
|
and demonstrates the usage of the RMT peripheral::
|
|
|
|
nsh> rmtchar
|
|
|
|
**WS2812 addressable RGB LEDs**
|
|
|
|
This same configuration enables the usage of the RMT peripheral and the example
|
|
``ws2812`` to drive addressable RGB LEDs::
|
|
|
|
nsh> ws2812
|
|
|
|
Please note that this board contains an on-board WS2812 LED connected to GPIO8
|
|
and, by default, this config configures the RMT transmitter in the same pin.
|
|
|
|
rtc
|
|
---
|
|
|
|
This configuration demonstrates the use of the RTC driver through alarms.
|
|
You can set an alarm, check its progress and receive a notification after it expires::
|
|
|
|
nsh> alarm 10
|
|
alarm_daemon started
|
|
alarm_daemon: Running
|
|
Opening /dev/rtc0
|
|
Alarm 0 set in 10 seconds
|
|
nsh> alarm -r
|
|
Opening /dev/rtc0
|
|
Alarm 0 is active with 10 seconds to expiration
|
|
nsh> alarm_daemon: alarm 0 received
|
|
|
|
spi
|
|
--------
|
|
|
|
This configuration enables the support for the SPI driver.
|
|
You can test it by connecting MOSI and MISO pins which are GPIO7 and GPIO2
|
|
by default to each other and running the ``spi`` example::
|
|
|
|
nsh> spi exch -b 2 "AB"
|
|
Sending: AB
|
|
Received: AB
|
|
|
|
spiflash
|
|
--------
|
|
|
|
This config tests the external SPI that comes with the ESP32-C6 module connected
|
|
through SPI1.
|
|
|
|
By default a SmartFS file system is selected.
|
|
Once booted you can use the following commands to mount the file system::
|
|
|
|
nsh> mksmartfs /dev/smart0
|
|
nsh> mount -t smartfs /dev/smart0 /mnt
|
|
|
|
sta_softap
|
|
----------
|
|
|
|
With this configuration you can run these commands to be able
|
|
to connect your smartphone or laptop to your board::
|
|
|
|
nsh> ifup wlan1
|
|
nsh> dhcpd_start wlan1
|
|
nsh> wapi psk wlan1 mypasswd 3
|
|
nsh> wapi essid wlan1 nuttxap 1
|
|
|
|
In this case, you are creating the access point ``nuttxapp`` in your board and to
|
|
connect to it on your smartphone you will be required to type the password ``mypasswd``
|
|
using WPA2.
|
|
|
|
.. tip:: Please refer to :ref:`ESP32 Wi-Fi SoftAP Mode <esp32_wi-fi_softap>`
|
|
for more information.
|
|
|
|
The ``dhcpd_start`` is necessary to let your board to associate an IP to your smartphone.
|
|
|
|
timer
|
|
-----
|
|
|
|
This config test the general use purpose timers. It includes the 4 timers,
|
|
adds driver support, registers the timers as devices and includes the timer
|
|
example.
|
|
|
|
To test it, just run the following::
|
|
|
|
nsh> timer -d /dev/timerx
|
|
|
|
Where x in the timer instance.
|
|
|
|
twai
|
|
----
|
|
|
|
This configuration enables the support for the TWAI (Two-Wire Automotive Interface) driver.
|
|
You can test it by connecting TWAI RX and TWAI TX pins which are GPIO0 and GPIO2 by default
|
|
to an external transceiver or connecting TWAI RX to TWAI TX pin by enabling
|
|
the `CONFIG_CAN_LOOPBACK` option (``Device Drivers -> CAN Driver Support -> CAN loopback mode``)
|
|
and running the ``can`` example::
|
|
|
|
nsh> can
|
|
nmsgs: 0
|
|
min ID: 1 max ID: 2047
|
|
Bit timing:
|
|
Baud: 1000000
|
|
TSEG1: 15
|
|
TSEG2: 4
|
|
SJW: 3
|
|
ID: 1 DLC: 1
|
|
|
|
usbconsole
|
|
----------
|
|
|
|
This configuration tests the built-in USB-to-serial converter found in ESP32-C6.
|
|
``esptool`` can be used to check the version of the chip and if this feature is
|
|
supported. Running ``esptool.py -p <port> chip_id`` should have ``Chip is
|
|
ESP32-C6`` in its output.
|
|
When connecting the board a new device should appear, a ``/dev/ttyACMX`` on Linux
|
|
or a ``/dev/cu.usbmodemXXX`` om macOS.
|
|
This can be used to flash and monitor the device with the usual commands::
|
|
|
|
make download ESPTOOL_PORT=/dev/ttyACM0
|
|
minicom -D /dev/ttyACM0
|
|
|
|
watchdog
|
|
--------
|
|
|
|
This configuration tests the watchdog timers. It includes the 1 MWDTS,
|
|
adds driver support, registers the WDTs as devices and includes the watchdog
|
|
example application.
|
|
|
|
To test it, just run the following command::
|
|
|
|
nsh> wdog -i /dev/watchdogX
|
|
|
|
Where X is the watchdog instance.
|
|
|
|
wifi
|
|
----
|
|
|
|
Enables Wi-Fi support. You can define your credentials this way::
|
|
|
|
$ make menuconfig
|
|
-> Application Configuration
|
|
-> Network Utilities
|
|
-> Network initialization (NETUTILS_NETINIT [=y])
|
|
-> WAPI Configuration
|
|
|
|
Or if you don't want to keep it saved in the firmware you can do it
|
|
at runtime::
|
|
|
|
nsh> wapi psk wlan0 mypasswd 3
|
|
nsh> wapi essid wlan0 myssid 1
|
|
nsh> renew wlan0
|
|
|
|
.. tip:: Please refer to :ref:`ESP32 Wi-Fi Station Mode <esp32_wi-fi_sta>`
|
|
for more information.
|