incubator-nuttx/include/nuttx/wireless/ioctl.h

97 lines
4.2 KiB
C

/****************************************************************************
* include/nuttx/wireless/ioctl.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/* This file includes common definitions to be used in all wireless
* character drivers (when applicable).
*/
#ifndef __INCLUDE_NUTTX_WIRELESS_IOCTL_H
#define __INCLUDE_NUTTX_WIRELESS_IOCTL_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <nuttx/fs/ioctl.h>
#ifdef CONFIG_DRIVERS_WIRELESS
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/****************************************************************************
* Character Driver IOCTL commands
* Non-compatible, NuttX only IOCTL definitions for use with low-level
* wireless drivers that are accessed via a character device.
* Use of these IOCTL commands requires a file descriptor created by
* the open() interface.
****************************************************************************/
#define WLIOC_SETRADIOFREQ _WLCIOC(0x0001) /* arg: Pointer to uint32_t, */
/* frequency value (in MHz) */
#define WLIOC_GETRADIOFREQ _WLCIOC(0x0002) /* arg: Pointer to uint32_t, */
/* frequency value (in MHz) */
#define WLIOC_SETADDR _WLCIOC(0x0003) /* arg: Pointer to address value, format
* of the address is driver specific */
#define WLIOC_GETADDR _WLCIOC(0x0004) /* arg: Pointer to address value, format
* of the address is driver specific */
#define WLIOC_SETTXPOWER _WLCIOC(0x0005) /* arg: Pointer to int32_t, */
/* output power (in dBm) */
#define WLIOC_GETTXPOWER _WLCIOC(0x0006) /* arg: Pointer to int32_t, */
/* output power (in dBm) */
/****************************************************************************
* Device-specific IOCTL commands
****************************************************************************/
#define WL_FIRST 0x0001 /* First common command */
#define WL_NCMDS 0x0006 /* Number of common commands */
/* User defined ioctl commands are also supported. These will be forwarded
* by the upper-half driver to the lower-half driver via the ioctl()
* method of the lower-half interface. However, the lower-half driver
* must reserve a block of commands as follows in order prevent IOCTL
* command numbers from overlapping.
*/
/* See include/nuttx/wireless/nrf24l01.h */
#define NRF24L01_FIRST (WL_FIRST + WL_NCMDS)
#define NRF24L01_NCMDS 16
/* See include/nuttx/wireless/lpwan/sx127x.h */
#define SX127X_FIRST (NRF24L01_FIRST + NRF24L01_NCMDS)
#define SX127X_NCMDS 11
/* See include/nuttx/wireless/gs2200m.h */
#define GS2200M_FIRST (SX127X_FIRST + SX127X_NCMDS)
#define GS2200M_NCMDS 9
/****************************************************************************
* Public Types
****************************************************************************/
#endif /* CONFIG_DRIVERS_WIRELESS */
#endif /* __INCLUDE_NUTTX_WIRELESS_IOCTL_H */