169 lines
5.7 KiB
C
169 lines
5.7 KiB
C
/****************************************************************************
|
|
* boards/arm/rp2040/seeed-xiao-rp2040/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_ARM_RP2040_SEEED_XIAO_INCLUDE_BOARD_H
|
|
#define __BOARDS_ARM_RP2040_SEEED_XIAO_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#include "rp2040_i2cdev.h"
|
|
#include "rp2040_spidev.h"
|
|
#include "rp2040_i2sdev.h"
|
|
|
|
#include "rp2040_spisd.h"
|
|
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdint.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
#define MHZ 1000000
|
|
|
|
#define BOARD_XOSC_FREQ (12 * MHZ)
|
|
#define BOARD_PLL_SYS_FREQ (125 * MHZ)
|
|
#define BOARD_PLL_USB_FREQ (48 * MHZ)
|
|
|
|
#define BOARD_REF_FREQ (12 * MHZ)
|
|
#define BOARD_SYS_FREQ (125 * MHZ)
|
|
#define BOARD_PERI_FREQ (125 * MHZ)
|
|
#define BOARD_USB_FREQ (48 * MHZ)
|
|
#define BOARD_ADC_FREQ (48 * MHZ)
|
|
#define BOARD_RTC_FREQ 46875
|
|
|
|
#define BOARD_UART_BASEFREQ BOARD_PERI_FREQ
|
|
|
|
#define BOARD_TICK_CLOCK (1 * MHZ)
|
|
|
|
/* GPIO definitions *********************************************************/
|
|
|
|
#define BOARD_GPIO_LED_PIN_B 25
|
|
#define BOARD_GPIO_LED_PIN_R 17
|
|
#define BOARD_GPIO_LED_PIN_G 16
|
|
|
|
#define BOARD_NGPIOOUT 3
|
|
#define BOARD_NGPIOIN 1
|
|
#define BOARD_NGPIOINT 1
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs
|
|
* in any way. The following definitions are used to access individual LEDs.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define BOARD_LED1 0
|
|
#define BOARD_LED2 1
|
|
#define BOARD_LED3 2
|
|
|
|
#define BOARD_NLEDS 3
|
|
|
|
#define BOARD_LED_BLUE BOARD_LED1
|
|
#define BOARD_LED_RED BOARD_LED2
|
|
#define BOARD_LED_GREEN BOARD_LED3
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED1_BIT (1 << BOARD_LED1)
|
|
#define BOARD_LED2_BIT (1 << BOARD_LED2)
|
|
#define BOARD_LED3_BIT (1 << BOARD_LED3)
|
|
|
|
/* This LED is not used by the board port unless CONFIG_ARCH_LEDS is
|
|
* defined. In that case, the usage by the board port is defined in
|
|
* include/board.h and src/rp2040_autoleds.c. The LED is used to encode
|
|
* OS-related events as follows:
|
|
*
|
|
* -------------------- ----------------------------- ------
|
|
* SYMBOL Meaning LED
|
|
* -------------------- ----------------------------- ------
|
|
*/
|
|
|
|
#define LED_STARTED 0 /* NuttX has been started OFF */
|
|
#define LED_HEAPALLOCATE 0 /* Heap has been allocated OFF */
|
|
#define LED_IRQSENABLED 0 /* Interrupts enabled OFF */
|
|
#define LED_STACKCREATED 1 /* Idle stack created ON */
|
|
#define LED_INIRQ 2 /* In an interrupt N/C */
|
|
#define LED_SIGNAL 2 /* In a signal handler N/C */
|
|
#define LED_ASSERTION 2 /* An assertion failed N/C */
|
|
#define LED_PANIC 3 /* The system has crashed FLASH */
|
|
#undef LED_IDLE /* Not used */
|
|
|
|
/* Thus if the LED is statically on, NuttX has successfully booted and is,
|
|
* apparently, running normally. If the LED is flashing at approximately
|
|
* 2Hz, then a fatal error has been detected and the system has halted.
|
|
*/
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Name: rp2040_boardearlyinitialize
|
|
*
|
|
* Description:
|
|
*
|
|
****************************************************************************/
|
|
|
|
void rp2040_boardearlyinitialize(void);
|
|
|
|
/****************************************************************************
|
|
* Name: rp2040_boardinitialize
|
|
*
|
|
* Description:
|
|
*
|
|
****************************************************************************/
|
|
|
|
void rp2040_boardinitialize(void);
|
|
|
|
#undef EXTERN
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_ARM_RP2040_SEEED_XIAO_INCLUDE_BOARD_H */
|