290 lines
11 KiB
C
290 lines
11 KiB
C
/****************************************************************************
|
|
* configs/lpc4357-evb/include/board.h
|
|
*
|
|
* Copyright (C) 2014 Gregory Nutt. All rights reserved.
|
|
* Author: Gregory Nutt <gnutt@nuttx.org>
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in
|
|
* the documentation and/or other materials provided with the
|
|
* distribution.
|
|
* 3. Neither the name NuttX nor the names of its contributors may be
|
|
* used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
|
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
|
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef _CONFIGS_LPC4357_EVB_INCLUDE_BOARD_H
|
|
#define _CONFIGS_LPC4357_EVB_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
#include <stdbool.h>
|
|
|
|
#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_LPC43_GPIO_IRQ)
|
|
# include <nuttx/irq.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Clocking ****************************************************************/
|
|
/* NOTE: The following definitions require lpc43_cgu.h. It is not included
|
|
* here because the including C file may not have that file in its include
|
|
* path.
|
|
*
|
|
* The Xplorer board has four crystals on board:
|
|
*
|
|
* Y1 - RTC 32.768 MHz oscillator input,
|
|
* Y2 - 24.576 MHz input to the UDA 1380 audio codec,
|
|
* Y3 - 12.000 MHz LPC43xx crystal oscillator input
|
|
* Y4 - 50 MHz input for Ethernet
|
|
*/
|
|
|
|
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency (Y3) */
|
|
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency (Y1) */
|
|
#define BOARD_INTRCOSC_FREQUENCY (4000000) /* Internal RC oscillator frequency */
|
|
|
|
/* Integer and direct modes are supported:
|
|
*
|
|
* In integer mode (Fclkout < 156000000):
|
|
* Fclkin = BOARD_XTAL_FREQUENCY
|
|
* Fclkout = Msel * FClkin / Nsel
|
|
* Fcco = 2 * Psel * Fclkout
|
|
* In direct mode (Fclkout > 156000000):
|
|
* Fclkin = BOARD_XTAL_FREQUENCY
|
|
* Fclkout = Msel * FClkin / Nsel
|
|
* Fcco = Fclkout
|
|
*/
|
|
|
|
#ifdef CONFIG_LPC43_72MHz
|
|
|
|
/* NOTE: At 72MHz, the calibrated value of CONFIG_BOARD_LOOPSPERMSEC was
|
|
* determined to be:
|
|
*
|
|
* CONFIG_BOARD_LOOPSPERMSEC=7191
|
|
*
|
|
* executing from SRAM.
|
|
*/
|
|
|
|
/* Final clocking (Integer mode with no ramp-up)
|
|
*
|
|
* Fclkout = 6 * 12MHz / 1 = 72MHz
|
|
* Fcco = 2 * 2 * 72MHz = 216MHz
|
|
*/
|
|
|
|
# define BOARD_PLL_MSEL (6) /* Msel = 6 */
|
|
# define BOARD_PLL_NSEL (1) /* Nsel = 1 */
|
|
# define BOARD_PLL_PSEL (2) /* Psel = 2 */
|
|
|
|
# define BOARD_FCLKOUT_FREQUENCY (72000000) /* 6 * 12,000,000 / 1 */
|
|
# define BOARD_FCCO_FREQUENCY (244000000) /* 2 * 2 * Fclkout */
|
|
|
|
#else
|
|
|
|
/* NOTE: At 72MHz, the calibrated value of CONFIG_BOARD_LOOPSPERMSEC was
|
|
* determined to be:
|
|
*
|
|
* CONFIG_BOARD_LOOPSPERMSEC=18535
|
|
*
|
|
* executing from SRAM.
|
|
*/
|
|
|
|
/* Intermediate ramp-up clocking (Integer mode). If BOARD_PLL_RAMP_MSEL
|
|
* is not defined, there will be no ramp-up.
|
|
*
|
|
* Fclkout = 9 * 12MHz / 1 = 108MHz
|
|
* Fcco = 2 * 1 * 108MHz = 216MHz
|
|
*/
|
|
|
|
# define BOARD_PLL_RAMP_MSEL (9) /* Msel = 9 */
|
|
# define BOARD_PLL_RAMP_NSEL (1) /* Nsel = 1 */
|
|
# define BOARD_PLL_RAMP_PSEL (1) /* Psel = 1 */
|
|
|
|
# define BOARD_RAMP_FCLKOUT (108000000) /* 9 * 12,000,000 / 1 */
|
|
# define BOARD_RAMP_FCCO (216000000) /* 2 * 1 * Fclkout */
|
|
|
|
/* Final clocking (Direct mode).
|
|
*
|
|
* Fclkout = 17 * 12MHz / 1 = 204MHz
|
|
* Fcco = Fclockout = 204MHz
|
|
*/
|
|
|
|
# define BOARD_PLL_MSEL (17) /* Msel = 17 */
|
|
# define BOARD_PLL_NSEL (1) /* Nsel = 1 */
|
|
|
|
# define BOARD_FCLKOUT_FREQUENCY (204000000) /* 17 * 12,000,000 / 1 */
|
|
# define BOARD_FCCO_FREQUENCY (204000000) /* Fclockout */
|
|
|
|
#endif
|
|
|
|
/* This is the clock setup we configure for:
|
|
*
|
|
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Select Main oscillator for source
|
|
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz -> PLL0 multipler=20, pre-divider=1
|
|
* CCLCK = 480MHz / 6 = 80MHz -> CCLK divider = 6
|
|
*/
|
|
|
|
#define LPC43_CCLK BOARD_FCLKOUT_FREQUENCY
|
|
|
|
/* USB0 ********************************************************************/
|
|
/* Settings needed in lpc43_cpu.c */
|
|
|
|
#define BOARD_USB0_CLKSRC PLL0USB_CLKSEL_XTAL
|
|
#define BOARD_USB0_MDIV 0x06167ffa /* Table 149 datsheet, valid for 12Mhz Fclkin */
|
|
#define BOARD_USB0_NP_DIV 0x00302062 /* Table 149 datsheet, valid for 12Mhz Fclkin */
|
|
|
|
/* SPIFI clocking **********************************************************/
|
|
/* The SPIFI will receive clocking from a divider per the settings provided
|
|
* in this file. The NuttX code will configure PLL1 as the input clock
|
|
* for the selected divider
|
|
*/
|
|
|
|
#undef BOARD_SPIFI_PLL1 /* No division */
|
|
#undef BOARD_SPIFI_DIVA /* Supports division by 1-4 */
|
|
#undef BOARD_SPIFI_DIVB /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVC /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVD /* Supports division by 1-16 */
|
|
#undef BOARD_SPIFI_DIVE /* Supports division by 1-256 */
|
|
|
|
#if BOARD_FCLKOUT_FREQUENCY < 20000000
|
|
# define BOARD_SPIFI_PLL1 1 /* Use PLL1 directly */
|
|
#else
|
|
# define BOARD_SPIFI_DIVB 1 /* Use IDIVB */
|
|
#endif
|
|
|
|
|
|
/* We need to configure the divider so that its output is as close to the
|
|
* desired SCLK value. The peak data transfer rate will be about half of
|
|
* this frequency in bytes per second.
|
|
*/
|
|
|
|
#if BOARD_FCLKOUT_FREQUENCY < 20000000
|
|
# define BOARD_SPIFI_FREQUENCY BOARD_FCLKOUT_FREQUENCY /* 72Mhz? */
|
|
#else
|
|
# define BOARD_SPIFI_DIVIDER (14) /* 204MHz / 14 = 14.57MHz */
|
|
# define BOARD_SPIFI_FREQUENCY (102000000) /* 204MHz / 14 = 14.57MHz */
|
|
#endif
|
|
|
|
/* UART clocking ***********************************************************/
|
|
/* Configure all U[S]ARTs to use the XTAL input frequency */
|
|
|
|
#define BOARD_USART0_CLKSRC BASE_USART0_CLKSEL_XTAL
|
|
#define BOARD_USART0_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
|
|
#define BOARD_UART1_CLKSRC BASE_UART1_CLKSEL_XTAL
|
|
#define BOARD_UART1_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
|
|
#define BOARD_USART2_CLKSRC BASE_USART2_CLKSEL_XTAL
|
|
#define BOARD_USART2_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
|
|
#define BOARD_USART3_CLKSRC BASE_USART3_CLKSEL_XTAL
|
|
#define BOARD_USART3_BASEFREQ BOARD_XTAL_FREQUENCY
|
|
|
|
/* LED definitions *********************************************************/
|
|
/* The LPC4357-EVB has one user-controllable LED labelled D6 controlled
|
|
* by the signal LED_3V3:
|
|
*
|
|
* ---- ------- -------------
|
|
* LED SIGNAL MCU
|
|
* ---- ------- -------------
|
|
* D6 LED_3V3 PE_7 GPIO7[7]
|
|
* ---- ------- -------------
|
|
*
|
|
* A low output illuminates the LED.
|
|
*
|
|
* LED index values for use with board_userled()
|
|
*/
|
|
|
|
#define BOARD_LED 0
|
|
#define BOARD_NLEDS 1
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define BOARD_LED _BIT (1 << BOARD_LED)
|
|
|
|
/* If CONFIG_ARCH_LEDS is defined, the LED will be controlled as follows
|
|
* for NuttX debug functionality (where NC means "No Change").
|
|
*/
|
|
/* LED */
|
|
#define LED_STARTED 0 /* OFF */
|
|
#define LED_HEAPALLOCATE 0 /* OFF */
|
|
#define LED_IRQSENABLED 0 /* OFF */
|
|
#define LED_STACKCREATED 1 /* ON */
|
|
#define LED_INIRQ 2 /* NC */
|
|
#define LED_SIGNAL 2 /* NC */
|
|
#define LED_ASSERTION 2 /* NC */
|
|
#define LED_PANIC 3 /* Flashing */
|
|
|
|
/* If CONFIG_ARCH_LEDS is not defined, then the LEDs are completely under
|
|
* control of the application. The following interfaces are then available
|
|
* for application control of the LEDs:
|
|
*
|
|
* void board_userled_initialize(void);
|
|
* void board_userled(int led, bool ledon);
|
|
* void board_userled_all(uint8_t ledset);
|
|
*/
|
|
|
|
/* Button definitions *******************************************************/
|
|
/* To be provided */
|
|
|
|
/* UART Pins ****************************************************************/
|
|
/* REVISIT: Thee are most likely left over from the LPC4330-Xplorer */
|
|
/* The LPC4357-EVB does not have RS-232 drivers or serial connectors on
|
|
* board. USART0 and UART1 are available on J8 as follows:
|
|
*
|
|
* ------ ------ -----------------------
|
|
* SIGNAL J8 PIN LPC4357FET256 PIN
|
|
* (TFBGA100 package)
|
|
* ------ ------ -----------------------
|
|
* U0_TXD pin 9 F6 P6_4 U0_TXD=Alt 2
|
|
* U0_RXD pin 10 F9 P6_5 U0_RXD=Alt 2
|
|
* U1_TXD pin 13 H8 P1_13 U1_TXD=Alt 1
|
|
* U1_RXD pin 14 J8 P1_14 U1_RXD=Alt 1
|
|
* ------ ------ -----------------------
|
|
*
|
|
* The following definitions must be provided so that the LPC43 serial
|
|
* driver can set up the U[S]ART for the serial console properly (see the
|
|
* file arch/arc/src/lpc43xx/lpc4310203050_pinconf.h for more info).
|
|
*/
|
|
|
|
#define PINCONF_U0_TXD PINCONF_U0_TXD_4
|
|
#define PINCONF_U0_RXD PINCONF_U0_RXD_4
|
|
#define PINCONF_U0_DIR PINCONF_U0_DIR_3
|
|
|
|
#define PINCONF_U1_TXD PINCONF_U1_TXD_1
|
|
#define PINCONF_U1_RXD PINCONF_U1_RXD_1
|
|
|
|
#define PINCONF_U2_TXD PINCONF_U2_TXD_3
|
|
#define PINCONF_U2_RXD PINCONF_U2_RXD_3
|
|
#define PINCONF_U2_DIR PINCONF_U2_DIR_2
|
|
|
|
#define PINCONF_U3_TXD PINCONF_U3_TXD_4
|
|
#define PINCONF_U3_RXD PINCONF_U3_RXD_4
|
|
#define PINCONF_U3_DIR PINCONF_U3_DIR_3
|
|
|
|
#endif /* _CONFIGS_LPC4357_EVB_INCLUDE_BOARD_H */
|