473 lines
26 KiB
C
473 lines
26 KiB
C
/****************************************************************************
|
|
* drivers/net/enc28j60.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
/* References:
|
|
* - ENC28J60 Data Sheet, Stand-Alone Ethernet Controller with SPI Interface,
|
|
* DS39662C, 2008 Microchip Technology Inc.
|
|
*/
|
|
|
|
#ifndef __DRIVERS_NET_ENC28J60_H
|
|
#define __DRIVERS_NET_ENC28J60_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* ENC28J60 Commands ********************************************************/
|
|
|
|
/* A total of seven instructions are implemented on the ENC28J60. Where:
|
|
*
|
|
* aaaaaa is the 5-bit address of a control register, and
|
|
* dddddddd is one or more bytes of data that may accompany the command.
|
|
*/
|
|
|
|
#define ENC_RCR (0x00) /* Read Control Register
|
|
* 000 | aaaaa | (Register value returned) */
|
|
#define ENC_RBM (0x3a) /* Read Buffer Memory
|
|
* 001 | 11010 | (Read buffer data follows) */
|
|
#define ENC_WCR (0x40) /* Write Control Register
|
|
* 010 | aaaaa | dddddddd */
|
|
#define ENC_WBM (0x7a) /* Write Buffer Memory
|
|
* 011 | 11010 | (Write buffer data follows) */
|
|
#define ENC_BFS (0x80) /* Bit Field Set
|
|
* 100 | aaaaa | dddddddd */
|
|
#define ENC_BFC (0xa0) /* Bit Field Clear
|
|
* 101 | aaaaa | dddddddd */
|
|
#define ENC_SRC (0xff) /* System Reset
|
|
* 111 | 11111 | (No data) */
|
|
|
|
/* Global Control Registers *************************************************/
|
|
|
|
/* Control registers are accessed with the RCR, RBM, WCR, BFS, and BFC
|
|
* commands. The following identifies all ENC28J60 control registers. The
|
|
* control register memory is partitioned into four banks, selectable by the
|
|
* bank select bits, BSEL1:BSEL0, in the ECON1 register.
|
|
*
|
|
* The last five locations (0x1b to 0x1f) of all banks point to a common set
|
|
* of registers: EIE, EIR, ESTAT, ECON2 and ECON1. These are key registers
|
|
* used in controlling and monitoring the operation of the device. Their
|
|
* common mapping allows easy access without switching the bank.
|
|
*
|
|
* Control registers for the ENC28J60 are generically grouped as ETH, MAC and
|
|
* MII registers. Register names starting with E belong to the ETH group.
|
|
* Similarly, registers names starting with MA belong to the MAC group and
|
|
* registers prefixed with MI belong to the MII group.
|
|
*/
|
|
|
|
#define ENC_EIE (0x1b) /* Ethernet Interrupt Enable Register */
|
|
#define ENC_EIR (0x1c) /* Ethernet Interrupt Request Register */
|
|
#define ENC_ESTAT (0x1d) /* Ethernet Status Register */
|
|
#define ENC_ECON2 (0x1e) /* Ethernet Control 2 Register */
|
|
#define ENC_ECON1 (0x1f) /* Ethernet Control 1 Register */
|
|
|
|
/* Ethernet Interrupt Enable Register Bit Definitions */
|
|
|
|
#define EIE_RXERIE (1 << 0) /* Bit 0: Receive Error Interrupt Enable */
|
|
#define EIE_TXERIE (1 << 1) /* Bit 1: Transmit Error Interrupt Enable */
|
|
/* Bit 2: Reserved */
|
|
#define EIE_TXIE (1 << 3) /* Bit 3: Transmit Enable */
|
|
#define EIE_LINKIE (1 << 4) /* Bit 4: Link Status Change Interrupt Enable */
|
|
#define EIE_DMAIE (1 << 5) /* Bit 5: DMA Interrupt Enable */
|
|
#define EIE_PKTIE (1 << 6) /* Bit 6: Receive Packet Pending Interrupt Enable */
|
|
#define EIE_INTIE (1 << 7) /* Bit 7: Global INT Interrupt Enable */
|
|
|
|
/* Ethernet Interrupt Request Register Bit Definitions */
|
|
|
|
#define EIR_RXERIF (1 << 0) /* Bit 0: Receive Error Interrupt */
|
|
#define EIR_TXERIF (1 << 1) /* Bit 1: Transmit Error Interrupt */
|
|
/* Bit 2: Reserved */
|
|
#define EIR_TXIF (1 << 3) /* Bit 3: Transmit Interrupt */
|
|
#define EIR_LINKIF (1 << 4) /* Bit 4: Link Change Interrupt */
|
|
#define EIR_DMAIF (1 << 5) /* Bit 5: DMA Interrupt */
|
|
#define EIR_PKTIF (1 << 6) /* Bit 6: Receive Packet Pending Interrupt */
|
|
/* Bit 7: Reserved */
|
|
#define EIR_ALLINTS (0x7b) /* All interrupts */
|
|
|
|
/* Ethernet Status Register Bit Definitions */
|
|
|
|
#define ESTAT_CLKRDY (1 << 0) /* Bit 0: Clock Ready */
|
|
#define ESTAT_TXABRT (1 << 1) /* Bit 1: Transmit Abort Error */
|
|
#define ESTAT_RXBUSY (1 << 2) /* Bit 2: Receive Busy */
|
|
/* Bit 3: Reserved */
|
|
#define ESTAT_LATECOL (1 << 4) /* Bit 4: Late Collision Error */
|
|
/* Bit 5: Reserved */
|
|
#define ESTAT_BUFER (1 << 6) /* Bit 6: Ethernet Buffer Error Status */
|
|
#define ESTAT_INT (1 << 7) /* Bit 7: INT Interrupt */
|
|
|
|
/* Ethernet Control 1 Register Bit Definitions */
|
|
|
|
#define ECON1_BSEL_SHIFT (0) /* Bits 0-1: Bank select */
|
|
#define ECON1_BSEL_MASK (3 << ECON1_BSEL_SHIFT)
|
|
# define ECON1_BSEL_BANK0 (0 << ECON1_BSEL_SHIFT) /* Bank 0 */
|
|
# define ECON1_BSEL_BANK1 (1 << ECON1_BSEL_SHIFT) /* Bank 1 */
|
|
# define ECON1_BSEL_BANK2 (2 << ECON1_BSEL_SHIFT) /* Bank 2 */
|
|
# define ECON1_BSEL_BANK3 (3 << ECON1_BSEL_SHIFT) /* Bank 3 */
|
|
|
|
#define ECON1_RXEN (1 << 2) /* Bit 2: Receive Enable */
|
|
#define ECON1_TXRTS (1 << 3) /* Bit 3: Transmit Request to Send */
|
|
#define ECON1_CSUMEN (1 << 4) /* Bit 4: DMA Checksum Enable */
|
|
#define ECON1_DMAST (1 << 5) /* Bit 5: DMA Start and Busy Status */
|
|
#define ECON1_RXRST (1 << 6) /* Bit 6: Receive Logic Reset */
|
|
#define ECON1_TXRST (1 << 7) /* Bit 7: Transmit Logic Reset */
|
|
|
|
/* Ethernet Control 2 Register */
|
|
|
|
/* Bits 0-2: Reserved */
|
|
|
|
#define ECON2_VRPS (1 << 3) /* Bit 3: Voltage Regulator Power Save Enable */
|
|
/* Bit 4: Reserved */
|
|
#define ECON2_PWRSV (1 << 5) /* Bit 5: Power Save Enable */
|
|
#define ECON2_PKTDEC (1 << 6) /* Bit 6: Packet Decrement */
|
|
#define ECON2_AUTOINC (1 << 7) /* Bit 7: Automatic Buffer Pointer Increment Enable */
|
|
|
|
/* Banked Control Registers *************************************************/
|
|
|
|
/* The remaining control registers are identified with a a 5 bit address and
|
|
* a bank selection. We pack the bank number and an indication if this is
|
|
* a MAC/PHY register access together with the control register address
|
|
* together to keep the design simpler.
|
|
*/
|
|
|
|
#define ENC_ADDR_SHIFT (0) /* Bits 0-4: Register address */
|
|
#define ENC_ADDR_MASK (0x1f << ENC_ADDR_SHIFT)
|
|
#define ENC_BANK_SHIFT (5) /* Bits 5-6: Bank number */
|
|
#define ENC_BANK_MASK (3 << ENC_BSEL_SHIFT)
|
|
# define ENC_BANK0 (0 << ENC_BSEL_SHIFT)
|
|
# define ENC_BANK1 (1 << ENC_BSEL_SHIFT)
|
|
# define ENC_BANK2 (2 << ENC_BSEL_SHIFT)
|
|
# define ENC_BANK3 (3 << ENC_BSEL_SHIFT)
|
|
#define ENC_PHYMAC_SHIFT (7) /* Bit 7: This is a PHY/MAC command */
|
|
#define ENC_PHYMAC (1 << ENC_PHYMAC_SHIFT)
|
|
|
|
#define REGADDR(a,b,m) ((m) << ENC_PHYMAC_SHIFT | (b) << ENC_BANK_SHIFT | (a))
|
|
#define GETADDR(a) ((a) & ENC_ADDR_MASK)
|
|
#define GETBANK(a) (((a) >> ENC_BANK_SHIFT) & 3)
|
|
#define ISPHYMAC(a) (((a) & ENC_PHYMAC) != 0)
|
|
|
|
/* Bank 0 Control Register Addresses */
|
|
|
|
#define ENC_ERDPTL REGADDR(0x00, 0, 0) /* Read Pointer Low Byte (ERDPT<7:0> */
|
|
#define ENC_ERDPTH REGADDR(0x01, 0, 0) /* Read Pointer High Byte (ERDPT<12:8>) */
|
|
#define ENC_EWRPTL REGADDR(0x02, 0, 0) /* Write Pointer Low Byte (EWRPT<7:0>) */
|
|
#define ENC_EWRPTH REGADDR(0x03, 0, 0) /* Write Pointer High Byte (EWRPT<12:8>) */
|
|
#define ENC_ETXSTL REGADDR(0x04, 0, 0) /* TX Start Low Byte (ETXST<7:0>) */
|
|
#define ENC_ETXSTH REGADDR(0x05, 0, 0) /* TX Start High Byte (ETXST<12:8>) */
|
|
#define ENC_ETXNDL REGADDR(0x06, 0, 0) /* TX End Low Byte (ETXND<7:0>) */
|
|
#define ENC_ETXNDH REGADDR(0x07, 0, 0) /* TX End High Byte (ETXND<12:8>) */
|
|
#define ENC_ERXSTL REGADDR(0x08, 0, 0) /* RX Start Low Byte (ERXST<7:0>) */
|
|
#define ENC_ERXSTH REGADDR(0x09, 0, 0) /* RX Start High Byte (ERXST<12:8>) */
|
|
#define ENC_ERXNDL REGADDR(0x0a, 0, 0) /* RX End Low Byte (ERXND<7:0>) */
|
|
#define ENC_ERXNDH REGADDR(0x0b, 0, 0) /* RX End High Byte (ERXND<12:8>) */
|
|
#define ENC_ERXRDPTL REGADDR(0x0c, 0, 0) /* RX RD Pointer Low Byte (ERXRDPT<7:0>) */
|
|
#define ENC_ERXRDPTH REGADDR(0x0d, 0, 0) /* RX RD Pointer High Byte (ERXRDPT<12:8>) */
|
|
#define ENC_ERXWRPTL REGADDR(0x0e, 0, 0) /* RX WR Pointer Low Byte (ERXWRPT<7:0>) */
|
|
#define ENC_ERXWRPTH REGADDR(0x0f, 0, 0) /* RX WR Pointer High Byte (ERXWRPT<12:8>) */
|
|
#define ENC_EDMASTL REGADDR(0x10, 0, 0) /* DMA Start Low Byte (EDMAST<7:0>) */
|
|
#define ENC_EDMASTH REGADDR(0x11, 0, 0) /* DMA Start High Byte (EDMAST<12:8>) */
|
|
#define ENC_EDMANDL REGADDR(0x12, 0, 0) /* DMA End Low Byte (EDMAND<7:0>) */
|
|
#define ENC_EDMANDH REGADDR(0x13, 0, 0) /* DMA End High Byte (EDMAND<12:8>) */
|
|
#define ENC_EDMADSTL REGADDR(0x14, 0, 0) /* DMA Destination Low Byte (EDMADST<7:0>) */
|
|
#define ENC_EDMADSTH REGADDR(0x15, 0, 0) /* DMA Destination High Byte (EDMADST<12:8>) */
|
|
#define ENC_EDMACSL REGADDR(0x16, 0, 0) /* DMA Checksum Low Byte (EDMACS<7:0>) */
|
|
#define ENC_EDMACSH REGADDR(0x17, 0, 0) /* DMA Checksum High Byte (EDMACS<15:8>) */
|
|
/* 0x18-0x1a: Reserved */
|
|
/* 0x1b-0x1f: EIE, EIR, ESTAT, ECON2, ECON1 */
|
|
|
|
/* Bank 1 Control Register Addresses */
|
|
|
|
#define ENC_EHT0 REGADDR(0x00, 1, 0) /* Hash Table Byte 0 (EHT<7:0>) */
|
|
#define ENC_EHT1 REGADDR(0x01, 1, 0) /* Hash Table Byte 1 (EHT<15:8>) */
|
|
#define ENC_EHT2 REGADDR(0x02, 1, 0) /* Hash Table Byte 2 (EHT<23:16>) */
|
|
#define ENC_EHT3 REGADDR(0x03, 1, 0) /* Hash Table Byte 3 (EHT<31:24>) */
|
|
#define ENC_EHT4 REGADDR(0x04, 1, 0) /* Hash Table Byte 4 (EHT<39:32>) */
|
|
#define ENC_EHT5 REGADDR(0x05, 1, 0) /* Hash Table Byte 5 (EHT<47:40>) */
|
|
#define ENC_EHT6 REGADDR(0x06, 1, 0) /* Hash Table Byte 6 (EHT<55:48>) */
|
|
#define ENC_EHT7 REGADDR(0x07, 1, 0) /* Hash Table Byte 7 (EHT<63:56>) */
|
|
#define ENC_EPMM0 REGADDR(0x08, 1, 0) /* Pattern Match Mask Byte 0 (EPMM<7:0>) */
|
|
#define ENC_EPMM1 REGADDR(0x09, 1, 0) /* Pattern Match Mask Byte 1 (EPMM<15:8>) */
|
|
#define ENC_EPMM2 REGADDR(0x0a, 1, 0) /* Pattern Match Mask Byte 2 (EPMM<23:16>) */
|
|
#define ENC_EPMM3 REGADDR(0x0b, 1, 0) /* Pattern Match Mask Byte 3 (EPMM<31:24>) */
|
|
#define ENC_EPMM4 REGADDR(0x0c, 1, 0) /* Pattern Match Mask Byte 4 (EPMM<39:32>) */
|
|
#define ENC_EPMM5 REGADDR(0x0d, 1, 0) /* Pattern Match Mask Byte 5 (EPMM<47:40>) */
|
|
#define ENC_EPMM6 REGADDR(0x0e, 1, 0) /* Pattern Match Mask Byte 6 (EPMM<55:48>) */
|
|
#define ENC_EPMM7 REGADDR(0x0f, 1, 0) /* Pattern Match Mask Byte 7 (EPMM<63:56>) */
|
|
#define ENC_EPMCSL REGADDR(0x10, 1, 0) /* Pattern Match Checksum Low Byte (EPMCS<7:0>) */
|
|
#define ENC_EPMCSH REGADDR(0x11, 1, 0) /* Pattern Match Checksum High Byte (EPMCS<15:0>) */
|
|
/* 0x12-0x13: Reserved */
|
|
#define ENC_EPMOL REGADDR(0x14, 1, 0) /* Pattern Match Offset Low Byte (EPMO<7:0>) */
|
|
#define ENC_EPMOH REGADDR(0x15, 1, 0) /* Pattern Match Offset High Byte (EPMO<12:8>) */
|
|
/* 0x16-0x17: Reserved */
|
|
#define ENC_ERXFCON REGADDR(0x18, 1, 0) /* Receive Filter Configuration */
|
|
#define ENC_EPKTCNT REGADDR(0x19, 1, 0) /* Ethernet Packet Count */
|
|
/* 0x1a: Reserved */
|
|
/* 0x1b-0x1f: EIE, EIR, ESTAT, ECON2, ECON1 */
|
|
|
|
/* Receive Filter Configuration Bit Definitions */
|
|
|
|
#define ERXFCON_BCEN (1 << 0) /* Bit 0: Broadcast Filter Enable */
|
|
#define ERXFCON_MCEN (1 << 1) /* Bit 1: Multicast Filter Enable */
|
|
#define ERXFCON_HTEN (1 << 2) /* Bit 2: Hash Table Filter Enable */
|
|
#define ERXFCON_MPEN (1 << 3) /* Bit 3: Magic Packet Filter Enable */
|
|
#define ERXFCON_PMEN (1 << 4) /* Bit 4: Pattern Match Filter Enable */
|
|
#define ERXFCON_CRCEN (1 << 5) /* Bit 5: Post-Filter CRC Check Enable */
|
|
#define ERXFCON_ANDOR (1 << 6) /* Bit 6: AND/OR Filter Select */
|
|
#define ERXFCON_UCEN (1 << 7) /* Bit 7: Unicast Filter Enable */
|
|
|
|
/* Bank 2 Control Register Addresses */
|
|
|
|
#define ENC_MACON1 REGADDR(0x00, 2, 1) /* MAC Control 1 */
|
|
/* 0x01: Reserved */
|
|
#define ENC_MACON3 REGADDR(0x02, 2, 1) /* MAC Control 3 */
|
|
#define ENC_MACON4 REGADDR(0x03, 2, 1) /* MAC Control 4 */
|
|
#define ENC_MABBIPG REGADDR(0x04, 2, 1) /* Back-to-Back Inter-Packet Gap (BBIPG<6:0>) */
|
|
/* 0x05: Reserved */
|
|
#define ENC_MAIPGL REGADDR(0x06, 2, 1) /* Non-Back-to-Back Inter-Packet Gap Low Byte (MAIPGL<6:0>) */
|
|
#define ENC_MAIPGH REGADDR(0x07, 2, 1) /* Non-Back-to-Back Inter-Packet Gap High Byte (MAIPGH<6:0>) */
|
|
#define ENC_MACLCON1 REGADDR(0x08, 2, 1) /* MAC Collision Control 1 */
|
|
#define ENC_MACLCON2 REGADDR(0x09, 2, 1) /* MAC Collision Control 2 */
|
|
#define ENC_MAMXFLL REGADDR(0x0a, 2, 1) /* Maximum Frame Length Low Byte (MAMXFL<7:0>) */
|
|
#define ENC_MAMXFLH REGADDR(0x0b, 2, 1) /* Maximum Frame Length High Byte (MAMXFL<15:8>) */
|
|
/* 0x0c-0x11: Reserved */
|
|
#define ENC_MICMD REGADDR(0x12, 2, 1) /* MII Command Register */
|
|
/* 0x13: Reserved */
|
|
#define ENC_MIREGADR REGADDR(0x14, 2, 1) /* MII Register Address */
|
|
/* 0x15: Reserved */
|
|
#define ENC_MIWRL REGADDR(0x16, 2, 1) /* MII Write Data Low Byte (MIWR<7:0>) */
|
|
#define ENC_MIWRH REGADDR(0x17, 2, 1) /* MII Write Data High Byte (MIWR<15:8>) */
|
|
#define ENC_MIRDL REGADDR(0x18, 2, 1) /* MII Read Data Low Byte (MIRD<7:0>) */
|
|
#define ENC_MIRDH REGADDR(0x19, 2, 1) /* MII Read Data High Byte(MIRD<15:8>) */
|
|
/* 0x1a: Reserved */
|
|
/* 0x1b-0x1f: EIE, EIR, ESTAT, ECON2, ECON1 */
|
|
|
|
/* MAC Control 1 Register Bit Definitions */
|
|
|
|
#define MACON1_MARXEN (1 << 0) /* Bit 0: MAC Receive Enable */
|
|
#define MACON1_PASSALL (1 << 1) /* Bit 1: Pass All Received Frames Enable */
|
|
#define MACON1_RXPAUS (1 << 2) /* Bit 2: Pause Control Frame Reception Enable */
|
|
#define MACON1_TXPAUS (1 << 3) /* Bit 3: Pause Control Frame Transmission Enable */
|
|
/* Bits 4-7: Unimplemented or reserved */
|
|
|
|
/* MAC Control 1 Register Bit Definitions */
|
|
|
|
#define MACON3_FULDPX (1 << 0) /* Bit 0: MAC Full-Duplex Enable */
|
|
#define MACON3_FRMLNEN (1 << 1) /* Bit 1: Frame Length Checking Enable */
|
|
#define MACON3_HFRMLEN (1 << 2) /* Bit 2: Huge Frame Enable */
|
|
#define MACON3_PHDRLEN (1 << 3) /* Bit 3: Proprietary Header Enable */
|
|
#define MACON3_TXCRCEN (1 << 4) /* Bit 4: Transmit CRC Enable */
|
|
#define MACON3_PADCFG0 (1 << 5) /* Bit 5: Automatic Pad and CRC Configuration */
|
|
#define MACON3_PADCFG1 (1 << 6) /* Bit 6: " " " " " " " " " " */
|
|
#define MACON3_PADCFG2 (1 << 7) /* Bit 7: " " " " " " " " " " */
|
|
|
|
/* MAC Control 1 Register Bit Definitions */
|
|
|
|
#define MACON4_NOBKOFF (1 << 4) /* Bit 4: No Backoff Enable */
|
|
#define MACON4_BPEN (1 << 5) /* Bit 5: No Backoff During Backpressure Enable */
|
|
#define MACON4_DEFER (1 << 6) /* Bit 6: Defer Transmission Enable bit */
|
|
|
|
/* MII Command Register Bit Definitions */
|
|
|
|
#define MICMD_MIIRD (1 << 0) /* Bit 0: MII Read Enable */
|
|
#define MICMD_MIISCAN (1 << 1) /* Bit 1: MII Scan Enable */
|
|
|
|
/* Bank 3 Control Register Addresses */
|
|
|
|
#define ENC_MAADR5 REGADDR(0x00, 3, 1) /* MAC Address Byte 5 (MAADR<15:8>) */
|
|
#define ENC_MAADR6 REGADDR(0x01, 3, 1) /* MAC Address Byte 6 (MAADR<7:0>) */
|
|
#define ENC_MAADR3 REGADDR(0x02, 3, 1) /* MAC Address Byte 3 (MAADR<31:24>), OUI Byte 3 */
|
|
#define ENC_MAADR4 REGADDR(0x03, 3, 1) /* MAC Address Byte 4 (MAADR<23:16>) */
|
|
#define ENC_MAADR1 REGADDR(0x04, 3, 1) /* MAC Address Byte 1 (MAADR<47:40>), OUI Byte 1 */
|
|
#define ENC_MAADR2 REGADDR(0x05, 3, 1) /* MAC Address Byte 2 (MAADR<39:32>), OUI Byte 2 */
|
|
#define ENC_EBSTSD REGADDR(0x06, 3, 0) /* Built-in Self-Test Fill Seed (EBSTSD<7:0>) */
|
|
#define ENC_EBSTCON REGADDR(0x07, 3, 0) /* Built-in Self-Test Control */
|
|
#define ENC_EBSTCSL REGADDR(0x08, 3, 0) /* Built-in Self-Test Checksum Low Byte (EBSTCS<7:0>) */
|
|
#define ENC_EBSTCSH REGADDR(0x09, 3, 0) /* Built-in Self-Test Checksum High Byte (EBSTCS<15:8>) */
|
|
#define ENC_MISTAT REGADDR(0x0a, 3, 1) /* MII Status Register */
|
|
/* 0x0b-0x11: Reserved */
|
|
#define ENC_EREVID REGADDR(0x12, 3, 0) /* Ethernet Revision ID */
|
|
/* 0x13-0x14: Reserved */
|
|
#define ENC_ECOCON REGADDR(0x15, 3, 0) /* Clock Output Control */
|
|
/* 0x16: Reserved */
|
|
#define ENC_EFLOCON REGADDR(0x17, 3, 0) /* Ethernet Flow Control */
|
|
#define ENC_EPAUSL REGADDR(0x18, 3, 0) /* Pause Timer Value Low Byte (EPAUS<7:0>) */
|
|
#define ENC_EPAUSH REGADDR(0x19, 3, 0) /* Pause Timer Value High Byte (EPAUS<15:8>) */
|
|
/* 0x1a: Reserved */
|
|
/* 0x1b-0x1f: EIE, EIR, ESTAT, ECON2, ECON1 */
|
|
|
|
/* Built-in Self-Test Control Register Bit Definitions */
|
|
|
|
#define EBSTCON_BISTST (1 << 0) /* Bit 0: Built-in Self-Test Start/Busy */
|
|
#define EBSTCON_TME (1 << 1) /* Bit 1: Test Mode Enable */
|
|
#define EBSTCON_TMSEL0 (1 << 2) /* Bit 2: Test Mode Select */
|
|
#define EBSTCON_TMSEL1 (1 << 3) /* Bit 3: " " " " " " */
|
|
#define EBSTCON_PSEL (1 << 4) /* Bit 4: Port Select */
|
|
#define EBSTCON_PSV0 (1 << 5) /* Bit 5: Pattern Shift Value */
|
|
#define EBSTCON_PSV1 (1 << 6) /* Bit 6: " " " " " */
|
|
#define EBSTCON_PSV2 (1 << 7) /* Bit 7: " " " " " */
|
|
|
|
/* MII Status Register Register Bit Definitions */
|
|
|
|
#define MISTAT_BUSY (1 << 0) /* Bit 0: MII Management Busy */
|
|
#define MISTAT_SCAN (1 << 1) /* Bit 1: MII Management Scan Operation */
|
|
#define MISTAT_NVALID (1 << 2) /* Bit 2: MII Management Read Data Not Valid */
|
|
/* Bits 3-7: Reserved or unimplemented */
|
|
|
|
/* Ethernet Flow Control Register Bit Definitions */
|
|
|
|
#define EFLOCON_FCEN0 (1 << 0) /* Bit 0: Flow Control Enable */
|
|
#define EFLOCON_FCEN1 (1 << 1) /* Bit 1: " " " " " " */
|
|
#define EFLOCON_FULDPXS (1 << 2) /* Bit 2: Read-Only MAC Full-Duplex Shadow */
|
|
/* Bits 3-7: Reserved or unimplemented */
|
|
|
|
/* PHY Registers ************************************************************/
|
|
|
|
#define ENC_PHCON1 (0x00) /* PHY Control Register 1 */
|
|
#define ENC_PHSTAT1 (0x01) /* PHY Status 1 */
|
|
#define ENC_PHID1 (0x02) /* PHY ID Register 1 */
|
|
#define ENC_PHID2 (0x03) /* PHY ID Register 2 */
|
|
#define ENC_PHCON2 (0x10) /* PHY Control Register 2 */
|
|
#define ENC_PHSTAT2 (0x11) /* PHY Status 2 */
|
|
#define ENC_PHIE (0x12) /* PHY Interrupt Enable Register */
|
|
#define ENC_PHIR (0x13) /* PHY Interrupt Request Register */
|
|
#define ENC_PHLCON (0x14)
|
|
|
|
/* PHY Control Register 1 Register Bit Definitions */
|
|
|
|
#define PHCON1_PDPXMD (1 << 8) /* Bit 8: PHY Duplex Mode */
|
|
#define PHCON1_PPWRSV (1 << 11) /* Bit 11: PHY Power-Down */
|
|
#define PHCON1_PLOOPBK (1 << 14) /* Bit 14: PHY Loopback */
|
|
#define PHCON1_PRST (1 << 15) /* Bit 15: PHY Software Reset */
|
|
|
|
/* PHY Status 1 Register Bit Definitions */
|
|
|
|
#define PHSTAT1_JBSTAT (1 << 1) /* Bit 1: PHY Latching Jabber Status */
|
|
#define PHSTAT1_LLSTAT (1 << 2) /* Bit 2: PHY Latching Link Status */
|
|
#define PHSTAT1_PHDPX (1 << 11) /* Bit 11: PHY Half-Duplex Capable */
|
|
#define PHSTAT1_PFDPX (1 << 12) /* Bit 12: PHY Full-Duplex Capable */
|
|
|
|
/* PHY Control Register 2 Register Bit Definitions */
|
|
|
|
#define PHCON2_HDLDIS (1 << 8) /* Bit 8: PHY Half-Duplex Loopback Disable */
|
|
#define PHCON2_JABBER (1 << 10) /* Bit 10: Jabber Correction Disable */
|
|
#define PHCON2_TXDIS (1 << 13) /* Bit 13: Twisted-Pair Transmitter Disable */
|
|
#define PHCON2_FRCLINK (1 << 14) /* Bit 14: PHY Force Linkup */
|
|
|
|
/* PHY Status 2 Register Bit Definitions */
|
|
|
|
#define PHSTAT2_PLRITY (1 << 5) /* Bit 5: Polarity Status */
|
|
#define PHSTAT2_DPXSTAT (1 << 9) /* Bit 9: PHY Duplex Status */
|
|
#define PHSTAT2_LSTAT (1 << 10) /* Bit 10: PHY Link Status */
|
|
#define PHSTAT2_COLSTAT (1 << 11) /* Bit 11: PHY Collision Status */
|
|
#define PHSTAT2_RXSTAT (1 << 12) /* Bit 12: PHY Receive Status */
|
|
#define PHSTAT2_TXSTAT (1 << 13) /* Bit 13: PHY Transmit Status */
|
|
|
|
/* PHY Interrupt Enable Register Bit Definitions */
|
|
|
|
#define PHIE_PGEIE (1 << 1) /* Bit 1: PHY Global Interrupt Enable */
|
|
#define PHIE_PLNKIE (1 << 4) /* Bit 4: PHY Link Change Interrupt Enable */
|
|
|
|
/* PHIR Register Bit Definitions */
|
|
|
|
#define PHIR_PGIF (1 << 2) /* Bit 2: PHY Global Interrupt */
|
|
#define PHIR_PLNKIF (1 << 4) /* Bit 4: PHY Link Change Interrupt */
|
|
|
|
/* PHLCON Register Bit Definitions */
|
|
|
|
/* Bit 0: Reserved */
|
|
#define PHLCON_STRCH (1 << 1) /* Bit 1: LED Pulse Stretching Enable */
|
|
#define PHLCON_LFRQ0 (1 << 2) /* Bit 2: LED Pulse Stretch Time Configuration */
|
|
#define PHLCON_LFRQ1 (1 << 3) /* Bit 3: " " " " " " " " " */
|
|
#define PHLCON_LBCFG0 (1 << 4) /* Bit 4: LEDB Configuration */
|
|
#define PHLCON_LBCFG1 (1 << 5) /* Bit 5: " " " " */
|
|
#define PHLCON_LBCFG2 (1 << 6) /* Bit 6: " " " " */
|
|
#define PHLCON_LBCFG3 (1 << 7) /* Bit 7: " " " " */
|
|
#define PHLCON_LACFG0 (1 << 8) /* Bit 8: LEDA Configuration */
|
|
#define PHLCON_LACFG1 (1 << 9) /* Bit 9: " " " " */
|
|
#define PHLCON_LACFG2 (1 << 10) /* Bit 10: " " " " */
|
|
#define PHLCON_LACFG3 (1 << 11) /* Bit 11: " " " " */
|
|
|
|
/* Packet Memory ************************************************************/
|
|
|
|
/* 8-Kbyte Transmit/Receive Packet Dual Port SRAM */
|
|
|
|
#define PKTMEM_START 0x0000
|
|
#define PKTMEM_END 0x1fff
|
|
|
|
/* Ethernet frames are between 64 and 1518 bytes long */
|
|
|
|
#define MIN_FRAMELEN 64
|
|
#define MAX_FRAMELEN 1518
|
|
|
|
/* Packet Control Bits Definitions ******************************************/
|
|
|
|
#define PKTCTRL_POVERRIDE (1 << 0) /* Bit 0: Per Packet Override */
|
|
#define PKTCTRL_PCRCEN (1 << 1) /* Bit 1: Per Packet CRC Enable */
|
|
#define PKTCTRL_PPADEN (1 << 2) /* Bit 2: Per Packet Padding Enable */
|
|
#define PKTCTRL_PHUGEEN (1 << 3) /* Bit 3: Per Packet Huge Frame Enable */
|
|
|
|
/* RX Status Bit Definitions ************************************************/
|
|
|
|
#define RXSTAT_LDEVENT (1 << 0) /* Bit 0: Long event or pack dropped */
|
|
/* Bit 1: Reserved */
|
|
#define RXSTAT_CEPS (1 << 2) /* Bit 2: Carrier event previously seen */
|
|
/* Bit 3: Reserved */
|
|
#define RXSTAT_CRCERROR (1 << 4) /* Bit 4: Frame CRC field bad */
|
|
#define RXSTAT_LENERROR (1 << 5) /* Bit 5: Packet length != data length */
|
|
#define RXSTAT_LENRANGE (1 << 6) /* Bit 6: Type/length field > 1500 bytes */
|
|
#define RXSTAT_OK (1 << 7) /* Bit 7: Packet with valid CRC and no symbol errors */
|
|
#define RXSTAT_MCAST (1 << 8) /* Bit 8: Packet with multicast address */
|
|
#define RXSTAT_BCAST (1 << 9) /* Bit 9: Packet with broadcast address */
|
|
#define RXSTAT_DRIBBLE (1 << 10) /* Bit 10: Additional bits received after packet */
|
|
#define RXSTAT_CTRLFRAME (1 << 11) /* Bit 11: Control frame with valid type/length */
|
|
#define RXSTAT_PAUSE (1 << 12) /* Bit 12: Control frame with pause frame opcde */
|
|
#define RXSTAT_UNKOPCODE (1 << 13) /* Bit 13: Control frame with unknown opcode */
|
|
#define RXSTAT_VLANTYPE (1 << 14) /* Bit 14: Current frame is a VLAN tagged frame */
|
|
/* Bit 15: Zero */
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
/****************************************************************************
|
|
* Public Data
|
|
****************************************************************************/
|
|
|
|
#ifdef __cplusplus
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* __DRIVERS_NET_ENC28J60_H */
|